© MuxLab Inc. 94-000938-A SE-000938-A
2321 Cohen Road, Saint-Laurent, Quebec, Canada. H4R 2N7
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: [email protected] URL: www.muxlab.com
Specifications
Environment
12G-SDI, 6G-SDI, 3G-SDI, HD-SDI & SD-SDI.
Devices
Camera, projectors, monitors, TV.
Transmission
Transparent to the user.
Detection
Auto Detection of the 12G/6G/3G/HD/SD-SDI Signal.
Bandwidth
11.88bps & 11.88/1.001Gbps
Data Rates
1.485, 2.97, 5.96 & 11.88 Gbps
Output Impedance
75Ω
Signals
SDI protocol.
Supported Resolution
12G-SDI: 2160p50/59.94/60Hz (4:2:2)
6G-SDI: 2160p23.98/24/25/29.97/30Hz (4:2:2)
3G-SDI: 1080p50/59.94/60Hz (4:2:2)
HD-SDI: 1080p/23.98/24/25/29.97/30Hz
720p/50/59.94/60Hz
1080i/50/59.94/60Hz
SD-SDI: NTSC (59.94Hz), PAL (50Hz)
Audio
Up to 8 Audio Channels.
Ancillary Data
Supported
Input Signal
12G-SDI : SMPTE ST2082
6G-SDI : SMPTE ST2081
3G-SDI: SMPTE 424M, 425M
HD-SDI: SMPTE 292M, 296M
SD-SDI : SMPTE 259M, 344M
Connectors
One (1) BNC Female 75 Ohms, Gold Plated for input.
Four (4) BNC Female 75 Ohms, Gold Plated for outputs.
One (1) Locking Barrel Jack 2.1mm Power Connector.
Note: RG59 coaxial cables not included.
Cable Equalization
12G-SDI up to 230ft (70m)
6G-SDI up to 330ft (100m)
3G-SDI up to 594ft (180m)
Cable
RG-59 or better cable required.
Power Supply
One (1) 110-240V/5VDC power supply with interchangeable blades.
Power Consumption
3.0 Watt (Max)
Temperature
Operating: 0° to 40°C Storage: -20° to 60°C
Humidity: Up to 90% non-condensing
Enclosure
Metal
Dimensions
3.19” x 1.61” x 0.95” (81mm x 41mm x 24mm)
Weight
0.37lbs (0.17kg)
Compliance
Regulatory: FCC, CE, RoHS Flammability: 94V0
Warranty
2 years
Order Information
500727 12G-SDI 1x4 Splitter, 4K/60
12G-SDI 1X4 Splitter, 4K/60
500727
Quick Installation Guide
Overview
The 12G-SDI 1x4 Splitter, 4K/60 (500727) allows one (1) 12G/6G/3G/HD/SD-SDI
source to be distributed and amplified to up to four (4) 12G/6G/3G/HD/SD-SDI
displays. The splitter supports up to 4K (3840 X 2160) video and HD audio, including
480i (SD-SDI), 720p/1080i (HD-SDI), 1080p (3G-SDI), 4K/30 (6G-SDI) and 4K/60
(12G-SDI). The device automatically detects the 12G/6G/3G/HD/SD-SDI signal and re-
clocks and regenerates the signal at the output for extending distances between source
and displays. Additionally, all connectors are on the rear panel for neater cabling.
Applications
Applications include video production, broadcasting, outside broadcasting vehicle, SDI
camcorder, studio-to-studio, post-production, live events, medical imaging display,
mobile video.
Installation
1. Identify the connectors on the 12G-SDI 1x4 Splitter as indicated on the
product labels above.
2. Connect the source to the 12G-SDI Input of the splitter.
3. Connect up to four (4) display(s) to the 12G-SDI Outputs of the splitter.
4. Connect the 5 VDC power supply to the splitter first, and then plug the power
supply into an AC power outlet. If power is present, the power LED of the
© MuxLab Inc. 2020
splitter will be illuminated.
Note: Power ON the 12G-SDI 1x4 Splitter, 4K/60 only after all connections are
made.
5. Power the equipment and verify the image quality.
6. The appropriate Data Rate LED will be ON to show the input signal rate speed
and that the signal is locked.
7. The following diagram shows the final configuration.
Output Pairing
The outputs of this device work in pairs. Due to the high frequency and low jitter
requirement for 12G-SDI signals, to have the best performance it is strongly
recommended to use a 75ohm terminator if a paired SDI output port is not in use.
Please see the following table for the 12G-SDI output pairing:
Output Port
Pair A
Output 1 & 2
Pair B
Output 3 & 4
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions
with respect to the installation of the 12G-SDI 1x4 Splitter, 4K/60:
Symptom
Probable
Cause
Possible
Solutions
No Image
No power
• Check power connections
No Image
Source
• Check if the source is sending a signal.
No Image
Resolution
• Check if the source resolution is valid.
No Image
Coaxial Cable
• Check the coaxial cable.
No Image
Coaxial Cable distance
• Check the coaxial cable distance for the corresponding
resolution (see Specifications table).
No Image
Coaxial Cable Quality
• Check the coaxial cable type. It should be an RG-59 or better
coaxial cable.
Flickering
Image
Synchronization
• Check the coaxial Cable Quality or distance.
Choppy sound
Synchronization
• Check the coaxial Cable Quality or distance.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
/
