Ice-O-Matic EMF 2306 User manual

Ice-O-Matic
Brand
Ice-O-Matic
Model
EMF 2306
Category
Ice cube makers
Type
User manual
®
EMF 2306 Series
Flake ICE Maker
EMF 2306 on a B100 Bin
ICE-O-Matic
®
is the Best ICE Making Solution for:
Hard Water, Food Safety and Tight Spaces
✓ Produces up to 2624 lbs. (1193 Kgs.)* of ICE per day
✓ Constructed from sturdy, corrosion-resistant
300 series stainless steel
✓ Only 26 inches tall
✓ Available with an air-or water-or
remote-cooled condenser
*Rated at 70 ° (21°) Air / 50° (10°) Water
Problem
ICE-O-Matic
®
Tough
Constructed with a brass evaporator and rugged stainless
steel transport system enclosed in polyurethane insulation
Solution
Operating Environments
Built to last?
Tight-Fitting Spaces
Kitchen space utilization
Maximum ICE
Maximum ICE production in a minimum amount of space
with an ultra-low profile:
• 26 inches tall
• Maximum ICE production in a 48 inch wide cabinet
• Works on all industry dispensers and bins
Dirty Air Filter
Forget to change the air filter?
Filter-Free Air
No air filter to change
Dependable ICE
ICE-O-Matic Flake ICE Makers remove excess water by
pushing the flaked ICE through an extrusion process.
The result is high quality flaked ICE which is ideal for
medical, supermaket or restaurant applications.
Poor Ice Quality
Ice is too wet and soft
EMF 2306 Series Flake ICE Maker - Modular
I
S
O
9
0
0
1
C
E
R
T
I
F
I
E
D
fi
We reserve the right to make changes in design and construction at any time
without obligation.
2003© ICE-O-Matic Rev Code: 2007A-07/03-SS
ICE-O-Matic 11100 E. 45th Avenue, Denver, CO 80239
Tel. 303 371-3737 Fax. 303 371-6296 www.iceomatic.com
®
Air Out -
Both Sides
of ICE Maker
Air in -
Back of
of ICE Maker
Dimensions and Air Flow
Air Out -
Both Sides
of ICE Maker
24"
(610 mm)
76"
(1930 mm)
26"
(660 mm)
48"
(1219 mm)
31"
(787 mm)
EMF 2306
Conds. Air Temp. Water Temp. °F (°C)
Unit °F (°C) 80°(27°) 70°(21°) 50°(10°)
90° (32°) 1681 (764) 1808 (822) 1986 (903) 90° (32°) 1730 (786) 1860 (845) 2066 (939)
80° (27°) 1791 (814) 1926 (875) 2119 (963) 80° (27°) 1878 (854) 2019 (918) 2221 (1010)
70° (21°) 1904 (865) 2047 (930) 2252 (1024) 70° (21°) 2009 (913) 2160 (982) 2376 (1080)
90° (32°) 2068 (940) 2224 (1011) 2384 (1084) 90° (32°) 1968 (894) 2116 (962) 2254 (1024)
80° (27°) 2117 (962) 2276 (1035) 2504 (1138) 80° (27°) 1992 (906) 2142 (974) 2357 (1071)
70° (21°) 2218 (1008) 2385 (1084) 2624 (1193) 70° (21°) 2080 (945) 2236 (1016) 2460 (1118)
90° (32°) 1700 (773) 1828 (831) 2047 (931)
80° (27°) 1870 (850) 2010 (914) 2212 (1005)
70° (21°) 2009 (913) 2160 (982) 2376 (1080)
50° (10°) 2424 (1102)
30° (-1°) 2472 (1124)
0° (-18°) 2521 (1146
)
All specifications and performance data are subject
to normal manufacturing variances.
Air
Cooled
Water
Cooled
Remote
Cooled
OPERATING LIMITS
Ambient Temp. Range
Air & Water 50° - 104°F (10° - 40°C) 60Hz
50° - 110°F (10° - 43°C) 50Hz
Remote -20° - 120°F (-29° - 49°C) 60Hz
-20° - 110°F (-29° - 43°C) 50 Hz
Water Temp. Range 40° - 80°F (4.5° - 27°C)
Water Pressure Ice Maker Min. 20 psi (1.4 bar)
Water in Max. 60 psi (6.9 bar)
Condenser Inlet Water Min. 20 psi (1.4 bar)
(Water cooled only) Max. 60 psi (6.9 bar)
EMF2306AS Air 2252 (1024) 1808 (822) 12.0 (45) n/a 3.0 18978 208-230/60/1 3 14.9 15 370 (168)
EMF2306WS Water 2624 (1193) 2224 (1011) 12.0 (45) 182.8 (692) 2.2 21600 208-230/60/1 3 12.8 15 370 (168)
EMF2306RS Remote 2376 (1080) 1828 (831) 12.0 (45) n/a 3.1 19194 208-230/60/1 3 15.5 15 370 (168)
ERC -2062 Remote Condenser for 1 model EMF 2306RS (208-230/50-60/1 voltage) 125 (57)
RT-325-404 25 ft. (7.6m) Precharged Tubing Kit for R-404A models 13 (6)
RT-340-404 40 ft. (12m) Precharged Tubing Kit for R-404A models 18 (8)
RT-345-404 45 ft. (13.7m) Precharged Tubing Kit for R-404A models 19 (9)
RT-360-404 60 ft. (18.2m) Precharged Tubing Kit for R-404A models 26 (12)
See Bin specification sheet for information on ICE storage bins
Please note: air-cooled units require 6” (152 mm) clearance for air intake and exhaust.
Water Used-Gals. (Lits.) Kilowatts
ICEProduction ICE Production per 100 lbs. of Ice Used per
per 24 hrs. at per 24 hrs. at 90° Air/70° Water 100 lbs. of ICES Min. Max. Shipping
Model Cond. 70° Air/50° Water 90° Air/70° Water 90° Air Voltage No. of Circuit Fuse Weight
No. Unit lbs. (Kgs.) lbs. (Kgs.) 70° Water Btuh Characteristics Wires Amp. Size lbs. (Kgs.)
ICE Prod. Cond.
Use Use
60 Hz
ORDERING AND SPECIFICATION INFORMATION
ICE PRODUCTION CHART POUNDS
(KILOGRAMS) PER 24 HOURS
20.95"
(532mm)
TYP.
0.75" (19mm) TYP.
0.75" (19mm) TYP.
23.50"
(597mm)
0.75"
(19mm)
TYP.
9.00"
(229mm)
Hole for Strap
Mounting to Bin
ICE Maker - Water In
1/4" (6mm) Male Flare
ICE Machine - Water Out
9/16" (14mm) ID Plastic Tubing
0.50"
(13mm)
TYP.
9.00"
(229mm)
19.45"
(494mm)
TYP.
7/8" (22mm) DIA Hole
for Electrical Connections
to Control Box
7/8" (22mm) DIA Hole
for Electrical Connections
to Control Box for Remote
Condenser Fan Leads
Rear View
(Air Cooled)
48.00" (1219mm)
4.00" (102mm) TYP.
Minimum Wall
Clearance
ICE Dispense Area "To Bin"
in Bottom of Machine
- 5.50" (140mm)
11.41"
(290mm)
5.50"
(140mm)
TYP.
6.00"
(152mm)
Minimum Wall
Clearance
for Utility
Connections
Top View
26.00"
(660mm)
23.64"
(600mm)
Air Flow "Out"
R.H. Side View
20.95"
(532mm)
TYP.
0.75" (19mm) TYP.
0.75" (19mm) TYP.
23.50"
(597mm)
0.75"
(19mm)
TYP.
9.00"
(229mm)
Hole for Strap
Mounting to Bin
ICE Maker - Water In
1/4" (6mm) Male Flare
ICE Machine - Water Out
9/16" (14mm) ID Plastic Tubing
0.50"
(13mm)
TYP.
9.00"
(229mm)
19.45"
(494mm)
TYP.
7/8" (22mm) DIA Hole
for Electrical Connections
to Control Box
7/8" (22mm) DIA Hole
for Electrical Connections
to Control Box for Remote
Condenser Fan Leads
Rear View
(Air Cooled)
  • Page 1 1
  • Page 2 2

Ice-O-Matic EMF 2306 User manual

Ice-O-Matic
Brand
Ice-O-Matic
Model
EMF 2306
Category
Ice cube makers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents