Morphy Richards 28026 User manual

Brand: Morphy Richards

Model: 28026

Category: Alarm clocks

Type: User manual

This manual is also suitable for

IB28026

MSF clock radio

with pillow speaker

28026 OPERATING INSTRUCTIONS

Locations of control

Illustration

1314

Attention

Due to your clock radio operating by high precision software; an automatic reset

circuit is built in. In case of a software hang-up (ie. no display after power failure)

please unplug your unit from the mains and remove the back-up batteries, wait a few

minutes for the unit to discharge power completely. Then reapply the mains and refit

the back-up batteries.

1 RC signal receiver

2 Battery compartment

(located underneath the unit)

3 Remote pillow speaker w/snooze

button

4 Function switch

(on/off/auto)

5 Dial scale display

6 LCD display

7 Snooze/sleep off/weekend alarm

/daylight saving mode button

8 Mode button

9 Alarm button

10 Tuning control

11 Band selector

12 Volume/buzzer

(when alarm on) control

13 Speaker

14 Forward (+) / RC signal receiving

mode button

15 Backward (-) / Show button

16 Sleep ON button

Electrical requirements

Check that the voltage on the rating plate of your clock radio corresponds

with your house electricity supply which must be A.C. (Alternating current).

For clock radios with fitted plug.

If the socket outlets in your home are not suitable for the plug supplied

with this appliance the plug should be removed and the appropriate one

fitted.

IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED,

MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS

HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET.

Should the fuse in the 13 amp mains plug require changing a 3 amp BS1362

fuse must be fitted.

The socket outlet should be installed near the equipment and shall be easily

accessible.

Daylight saving time (DST) means at summer time you add one hour to

standard time.

1 In manual mode, you can manually able or disable the DST function. Press the

mode button (8) 5 times. The unit will be in local time setting mode. Choose your

city eg LON then press the Snooze button (7) once. The DST symbol

will

appear and one hour will be added to your local time.

Lcd display format

CITY

Day-light saving time

(DST) indicator

Enable RC

signal

Alarm 1

Sleep

indicator

Real time, date & World

time display

World time city

name display

Weekdays

Disable

RC signal

Alarm 2

pm/am

indicator

3 Press the mode button (8) 6 times. The unit will be at world time setting mode.

Choose the city you want to review, e.g. LAX Los Angeles. Press the Snooze button

(7) once. The DST symbol will appear. One hour will be added onto the world time.

Please note that this action will only affect that particular time zone, i.e. LAX time. It

will not change your local real time, i.e. LON.

Battery back-up facility (unit will work without a battery being fitted)

1 Remove the battery compartment cover (located underneath the unit) by

pushing in the clip and lifting off.

2 Insert a 2 x AAA batteries and connect to terminals (Ensure batteries are inserted

correctly)

3 Replace the battery compartment cover.

Should a power interruption occur the clock will continue to run, however, time

keeping will not be accurate.

If the optional battery is not installed in case of the AC power failure, the clock will go

through the automatic msf setting. You will need to reset the alarm when power is

restored.

Battery back-up is designed to operate for a short period only.

If the unit is not to be used for a prolonged period, remove the battery to avoid

battery leakage.

In the interests of environmental safety : dispose of batteries safely.

Radio controlled clock (automatic clock) operation

Once you plug in the power cable and install the back-up batteries in the battery

compartment (2).

1 All the segments go solid for 2 seconds (LCD panel back-light will come on

automatically).

2 The letters “LON” and the rc signal receiver symbol

will flash.

3 After a few seconds the display will show “— : — “ with the second section “00”.

4 When the RC signal has been received and decoded successfully, the second

section starts counting up. The real time clock is updated by the

signal which

goes solid and immediately switches to the Auto Run Mode.

If the RC signal has not been received and decoded successfully

1 Your unit will stay in “0:00” with all the symbols cleared and will stop receiving the

RC signal after 15 minutes.

2 Press the mode button (8) once to switch the unit into self quartz oscillation Auto

Run Mode. Please refer to the SETTING THE TIME AND DATE IN REAL TIME

SECTION to set the clock manually. (The date and time is defaulted to 2 January

2003 0:00).

3 If you wish to receive the RC signal again, press the RC signal receiving mode

button (14) to start receiving the signal.

Press the RC signal receiving button (14) to change the RC signal receiving mode

accordingly.

1 When the

symbol flashes you will start receiving the RC signal

2 When the

symbol clears your unit will start receiving the RC signal at 0:00 or

12:00 only.

NOTE:

a) In order to get a clear, accurate RC signal, your clock requires several minutes for

receiving. This is normal.

b) Please do not place the RC signal receiver (1) near any electronic or electrical

products to avoid any interference (e.g. TV set, computer, refrigerator etc).

Clock operation (operate without RC signal)

Your clock is designed to operate by either synchronizing with the RC signal or

built-in quartz oscillation, which means your clock can always be working even after

you have left the RC signal transmitting area.

Weak or no RC signal is detected:

When there is a weak RC signal (not enough for synchronizing), the “0:00” will

appear. Please set the clock manually. (Please refer to the clock setting section).

View your clock functions with mode button

Your clock is designed to view its varied functions by pressing mode button (8)

Please see below chart for reference:

Auto run (real time) mode Set clock (real time) Set Date (real time)

Review the world time Set City (real time) set alarm 2 Set alarm 1

NOTE: When no button has been pressed for 15 seconds and is not in auto run mode

your unit will switch back into auto run mode automatically.

Setting the time and date for real time

1 Press the mode button (8) and the current real time will be flashing.

2 Press forward button (14) or backward button (15) to change the setting by 1

minute per step. Press and hold the forward or backward button (for

approximately 3 seconds) to change the setting in fast mode of 10 minutes per

step.

3 Press the mode button (8) again to confirm the current setting and enter into the

date setting mode.

4 Press the forward button (14) or backward button (15) to change the setting by

1 day per step. Fast setting as above. (The date will be flashing in the LCD when

setting).

5 Press mode button (8) 3 times to confirm the current setting and enter into real

time city setting mode. Press the forward button (14) or the backward button

(15) to change the setting.

6 Press mode button (8) several times to return to auto run mode.

The clock will reset itself to the correct time at the following times 12:00, 01:00,

02:00 and 03:00 when in auto mode.

Reviewing / setting the alarm 1 and alarm 2

1 To review/set the alarm 1 time by pressing the mode button (8) three times and

the previous alarm setting will appear (the time and week days will be flashing).

2 Press the alarm (on/off) button (9) to enable/disable alarm.

The alarm enable symbol

will appear if you have activated the Alarm 1.

3 Press the weekend alarm (on/off) button (7) to enable/disable the weekend

alarm off function (5 of the weekday indicators Mo-Fr) will appear when the

weekend alarm off function was enabled and 7 of the weekday indicators (Su-Sa)

will appear when the weekend alarm off function is disabled).

4 Press the forward button (14) or backward button (15) to change the setting by

1 minute per step. Press and hold the forward or backward key (for

approximately 3 seconds) to change in fast mode 10 minutes per step.

5 Press the mode button (8) once to enter into the alarm 2 setting mode, the

current setting is confirmed or if no key is pressed for 15 seconds it will return to

real time with the current setting confirmed.

6 Repeat the above setting process for Alarm 1 (step 2 – step 6) to set alarm 2. (The

alarm enable symbol

will appear if you have activated alarm 2).

7 Press the mode button (8) several times until it returns to auto run mode. Then

turn the function switch (4) to ‘auto’ position.

8 Turn the volume/buzzer (12) to select between wake up by buzzer alarm or radio.

Select your desired radio station by using the tuning knob (10) and band

selector (11) and desired volume by volume control (12) if you wish to wake up

by radio

Note:

(a) The alarm 1 and alarm 2 can only be activated and cancelled at the alarm setting

mode by pressing the alarm button (9).

(b) The duration period for the buzzer alarm or radio is 59 minutes.

Setting the world time

1 Press the mode button (8) six times to enter into the world time setting mode.

(The current world time setting will appear and the world city will flash)

2 Press the forward button (14) or backward button (15) to change the setting by

1 zone per step.

3 Press the snooze button (7) to enable (or disable) the daylight saving function.

When daylight saving is enabled the

symbol will become solid.

4 Press mode button (8) once to return to the auto run mode with the current

setting confirmed or if no key is pressed for 15 seconds, the unit will return to the

auto run mode automatically with the current setting confirmed as valid.

Note:

(a) Please refer to page 11 (reference 2) for the details between city names and

abbreviations.

(b) For the detailed 24 hour world time zone, please refer to page 11 (reference 3).

When alarm is active

1 When any alarm is activated the buzzer or radio, press the snooze button (7) and

the buzzer/radio will be turned off temporarily for approximately 9 minutes and the

and/or

symbol will flash. (The duration of the snooze function is 59 minutes).

2 To disable the alarm for at least 24 hours press alarm button (9). (The alarm

button can also disable the snooze function).

Note:

(a) When the sleep mode, alarm 1, alarm 2 collides the latest has priority.

(b) As the alarm is activated, the sleep mode, if set, is terminated immediately.

alarm time.

Wake to pillow speaker

1 Set the desired alarm time as mentioned.

2 Plug in the pillow speaker (3) into the jack at the back of the clock. Buzzer or

radio will sound to wake you at the preset time. Press the snooze button on the

pillow speaker or the main unit until the alarm is disabled.

3 To turn the pillow speaker (3) off, slide the function switch (4) to the ‘off’ position

or press the alarm set/off button (9).

Radio operation

1 To turn the radio on, slide the function switch (4) to the on position.

2 Slide the band selector (11) to your desired waveband FM or MW.

3 Adjust the volume control (12) to the desired level.

4 Turn the tuning knob (10) to select your desired station.

5 To turn off the radio, slide the function switch (4) to off position.

Sleep to radio

1 To activate the sleep function press sleep button (16). (The sleep function works

on auto run mode with the function switch (4) not set to on position.

2 As the sleep function is being activated, the symbol will be shown on the

display and the previous setting of sleep duration will appear for at least 2

seconds. (The default setting of sleep function is 1 hour).

3 To change the duration of the sleep mode, press forward button (14) or

backward button (15) whilst the sleep duration is shown on the display. (The

sleep function duration can be set within 1 minute to 1 hour 59 minutes.)

4 The sleep function will be terminated when any of the following events happen:

- press snooze button (7) once

- move the function switch (4) to the on position

- when any alarm is active (buzzer alarm or radio was activated by the alarm)

Auto alternate display (show function)

1 When at the auto run mode, press the show button (15) to select between

showing the real time only, real time with world time, real time with date, real time

with world time and date. The symbol “— —“ will appear when the display is set

to show the real time only.

Note:

(a) The symbol “— W” will appear when the display is set to show the real time

and world time with city name.

(b) The symbol “D—“ will appear when the display is set to show the real time and the

date.

(d) The display will change showing for each information after approximately 2

seconds.

Maintenance

Do not expose your clock radio to extremes of temperature. The product should

be kept in a warm environment free from dust and damp. For external cleaning

use only a soft, clean, damp cloth. Use of detergents may damage the finish.

Technical specification

AC Power supply : 230v AC 50Hz

Battery back-up : 2 x AAA (not provided)

Radio : FM 88Mhz - 108Mhz

: MW 540Khz - 1600Khz

Warning labels

WARNING: to reduce the risk of electric shock, do not expose this

appliance to rain or moisture.

ATTENTION: To reduce the risk of electric shock, do not remove the cover.

There are no user serviceable parts inside the unit. Refer any servicing to

qualified personnel.

The lightning flash with arrowhead symbol within the triangle is a warning

sign alerting the user of ‘dangerous voltage’ inside the unit.

The exclamation point within the triangle is a warning sign alerting the

user of important instructions accompanying the product.

To prevent fire or shock hazard do not expose this apparatus to dripping and splashing.

123456789

10 11 12 13

14 15 16 17 18 19 20 21 22 23 24

+12 +13 +14 +15 +16 +17 +18 +19 +20 +21 +22 +23 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11

-12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 -23 -22 -21 -20 -19 -18 -17 -16 -15 -14 -13

Vancouver

Los Angeles

Chicago

New York

Mexico

Hawaii

Santiago

Buenos Aires

London

Paris

Berlin

Moscow

Madrid

Rome

Hong Kong

Beijing

Tokyo

Sydney

Perth

Reference 3

Reference 2

World city name with abbreviation

Abb Time diff City Abb Time diff City

LON 0.00 London WLG +12.00 Wellington

MUN +1.00 Munich -11 -11.00 (GMT –11)

CAI +2.00 Cairo HNL -10.00 Honolulu

MOW +3.00 Moscow ANC -9.00 Anchorage

DXB +4.00 Dubai LAX -8.00 Los Angeles

KHI +5.00 Karachi DEN -7.00 Denver

DAC +6.00 Dhaka CHI -6.00 Chicago

BKK +7.00 Bangkok NYC -5.00 New York

HKG +8.00 Hong Kong CCS -4.00 Caracas

TYO +9.00 Tokyo RIO -3.00 Rio de Janeiro

SYD +10.00 Sydney -2H -2.00 (GMT –2)

NOU +11.00 Noumea -1H -1.00 (GMT –1)

Guarantee

Morphy Richards products are manufactured to internationally accepted quality stand-

ards. In addition to your statutory rights, Morphy Richards guarantee your product to be

free from manufacturing and component defects for a period of TWO YEARS from date

of purchase.

If your product proves to be defective within 28 days of purchase, your Morphy Richards

dealer from whom the product was purchased will be pleased to replace it free of charge.

Should your product develop a defect within the guarantee period but after the re-

placement period, please return the product to the following address, together with the

proof of purchase, brief details of the symptoms and your own name and address.

After Sales Division

Morphy Richards Limited

Talbot Road

Mexborough

South Yorkshire

S64 8AJ

Your post office will provide a certificate of posting. The product will be repaired

and returned to you promptly.

If you need any further advice, please call our Helpline

on: 0870 060 2614 (Mon-Fri)

Morphy Richards Website: www.morphyrichards.co.uk

446/8001/94 Rev 2

Morphy Richards Ltd, Talbot Road, Mexborough, S64 8AJ

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and design.

The company, therefore reserves the right to change the specification of its models at any time.

Morphy Richards 28026 User manual

Brand: Morphy Richards

Model: 28026

Category: Alarm clocks

Type: User manual

This manual is also suitable for

IB28026

Download PDF

report

Morphy Richards 28026 User manual

This manual is also suitable for

Morphy Richards 28026 User manual

Related papers

Other documents