Moen 8410 User manual

Brand: Moen

Model: 8410

Category: Sanitary ware

Type: User manual

This manual is also suitable for

MT138A

INSTALLATION INSTRUCTIONS

LAVATORY FAUCETS

Four-Inch Centerset

6" X 2" WIDE

1/2" IPS

THREADED

CONNECTIONS

LIFT ROD

POSITION

USE SPACER TO INSTALL

ON THINNER LAVATORY

BOWLS OR COUNTERS

DISCARD SPACER WHEN

INSTALLING ON THICKER

LAVATORY BOWLS OR COUNTERS

1-3/4"

MAX.

4-3/4"

3-5/8" C.C.

1-3/4"

5" NOMINAL

OPEN

POSITION

5" NOMINAL

OPEN

POSITION

CONCENTRIX HANDLE

CONCENTRIX

HANDLE INSERT

3-5/8" C.C.

1-3/4"

3-5/8" C.C.

1-3/4"

5" NOMINAL

OPEN

POSITION

LEVER HANDLE KNOB HANDLE

With clamp bar, spacer and

mounting nut installed, tilt

clamp bar back as shown,

then drop faucet supplies

down through deck holes and

tighten from below. On decks

thicker than 3/4" you may

have to remove spacer.

Fits 4" centers and through a 1" minimum diameter hole.

All models equipped with a Moen Flow-Rator™.

TILT BACK

CLAMP BAR

8410, 8415, 8416, 8450, 8455

Always turn water off before disassembling the valve. Open valve handle to alleviate

water pressure to insure that complete water shut-off has been accomplished.

Before turning water on during either rough-in or trim-out, make sure that the cartridge retainer clip is in place. The cartridge

a nd r et a i ne r c li p w er e p ro p e rl y i ns t a ll e d an d t es te d be f o re l e av i n g t h e fa c t or y . Although it is u nl i k el y , it is n e ve r t he l e ss p os s i bl e

that through the handling of the valve by any number of persons the retainer clip may not be properly installed. This should

be carefully checked at time of rough-in and trim-out. If the retainer clip is not properly installed, water pressure could force

the cartridge out of the casting. Personal injury or water damage to the premises could result.

CAUTION:

CLIP

EAR

Complies with ASME A112.18.1M and CSA B125

FAUCET

CONNECTION

NIPPLE

TIGHTEN

NUT

HOLD WITH

WRENCH

Installation

Be sure lavatory or mounting surface is clean and dry. Place a bead of plumber's putty around the inside lip of the

gasket, position gasket on deck. Assemble clamp bars, spacers if needed, and mounting nuts to escutcheon sutds. Tilt

clamp bars back as shown in illustration, then place faucet supplies and sutds down through the deck holes.

WARNING: Hold the faucet connection nipples with a wrench when

tightening to prevent twisting and collapse of the tubing.

MT138A

DRAIN

PLUG

VANDALPROOF

HOLE

LIFT ROD

AND KNOB

LIFT ROD

STRAP

SCREW

SPRING

CLIP

LIFT ROD

STRAP

PIVOT

ROD

BOTTOM GASKET

FLAT WASHER

PIVOT NUT

PIVOT ROD

SEAT

2-1/8"

1-1/2"

PIPE

JOINT

COMPOUND

OR THREAD

SEAL

TAPE

(NOT

FURNISHED)

SEAT

PLUMBERS

PUTTY

MAX 2-1/2"

MIN 1-1/2"

MOUNTING

NUT

DRAIN

BODY

PIPE

JOINT

COMPOUND

(NOT

FURNISHED)

1-1/4"

TAILPIPE

BASIN

Lift Rod & Waste Assembly

(For model with grid strainer assembly follow steps 1-3 only)

1. Thoroughly clean around drain opening in lavatory basin. Apply

1/4 inch bead of plumber's putty (not furnished) around the

underside of seat (as shown).

2. Apply pipe joint compound or thread seal tape (not furnished) to top

threaded end of the drain body. Slip drain body up through the

drain opening and screw seat on the drain body.

3. Position the drain body (with pivot rod opening extending rear-

wa rd) and tigh ten mou ntin g nu t un til the d ra in bo dy is snug . Wipe

excess plumber's putty from the seat area. Apply pipe joint

compound (not furnished) to top threaded end of tailpipe and

screw into the drain body. Tighten firmly by hand.

4. Position the drain plug in either of the following ways:

A. VANDALPROOF - This design is to prevent unauthorized

removal of the drain plug. Unscrew the pivot nut and remove

the pivot rod. Inside the drain body position the pivot rod

through the drain plug hole as shown in the illustration below.

Screw the pivot nut back on the drain body. DO NOT

OVERTIGHTEN.

B. EASY REMOVAL - This design is for quick removal of drain

plug for cleaning. Just drop in the drain plug as shown in the

illustration below.

5. Hook up lift rod and knob, lift rod strap and spring clamp as

shown.

6. With the drain plug in full open position, adjust lift rod and knob

to clear faucet and tighten lift rod strap screw.

Flushing

IMPORTANT:

Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surface of

the faucet cartridge and cause a leak. To avoid damage, DO NOT OPERATE VALVE until you have followed these

instructions:

1. After installing and connecting your new faucet turn the valve on in the full cold position (handle

pointing to the right) and turn on the cold supply for 15 seconds.

2. Without closing the valve turn to the full hot position (handle pointing to the left) and turn on the hot

supply for 15 seconds.

3. Close the valve, unscrew aerator from the end of the spout and clean the cone screen.

4. Replace aerator. Check for leaks.

A. VANDALPROOF B. EASY REMOVAL

FOORPLADNAVDOR TOVIP

POSITION FOR

EASY REMOVAL

PIVOT ROD

Disassembly

CAUTION: Turn OFF both hot and cold water supplies. Open handle to alleviate water pressure to insure that

complete water shut-off has been accomplished.

For Knob Models:

1. Remove handle cover, handle screw, knob, stop tube, washer, and retainer clip.

For Concentrix Handle Models:

1. Remove handle cover, gasket, handle screw, handle insert, handle skirt, handle adapter, stop tube, and retainer clip.

For Lever Handle Models:

1. Remove handle cap and handle screw. Lift handle assembly up, keep the cartridge stem in the closed position, tilt up

and off. Remove clip retainer ring and retainer clip. Slide off grooved sleeve and spacer.

For All Models:

2. Using the cartridge twisting tool (furnished with the new Moen cartridge) and pliers, turn the cartridge back and forth

between 11 and 1 o'clock, then grasp the cartridge stem and pull out the cartridge. If the cartridge is difficult to

remove, use a Moen cartridge puller.

To Eliminate Cross-Piping on Back-To-Back Installations,

or To Correct Reversed Rough-In Where Hot and Cold Positions Are Reversed

Remove handle parts and stop tube (see "Disassembly"). Turn cartridge stem around so that the notched flat is turned

one half turn or 180°. Reinstall handle parts. Tighten handle screw securely; replace handle cover.

Cleaning & Care Instructions for

Special Finish Models:

All that is necessary to clean these faucets is to wipe them with a soft, damp cloth such as terrycloth. Warm water will

remove dry water spots. CAUTION: DO NOT use cleansers which contain abrasives or harsh chemicals. NEVER use

alcohol or other organic solvents. A high quality, non abrasive wax polish applied occasionally will help to preserve the

deep tones of the finish.

Reassembly

Fully insert the cartridge until the top of the cartridge ears are level with the top of the faucet body. Position the cartridge

ears up and down to allow insertion of the retainer clip (see illustration on page one). Replace the retainer clip (for lever

handles replace spacer, grooved sleeve, retainer clip, and clip retainer ring) so that the legs straddle the cartridge ears

and slide down into the bottom slot in the body. This prevents the cartridge from rotating and locks it in the body. Re-

install handle parts (For concentrix models make sure the gasket fits up under and into the handle cover recess, then

screw on the handle cover and hand tighten). Tighten handle screw securely. Press on handle cover. The notched flat

on the stem must point UP when mounting Knob or Concentrix Handles, DOWN for Lever Handle models.

STOP

TUBE

KNOB

HANDLE

SCREW

HANDLE

COVER

WASHER

HANDLE

SCREW

STOP

TUBE

HANDLE

ADAPTER

SKIRT

HANDLE

INSERT

SPACER

CLIP

RETAINER

RING

GROOVED

SLEEVE

HANDLE

ASSEMBLY

HANDLE

SCREW

HANDLE

COVER

RETAINER

CLIP

CARTRIDGE

HANDLE

COVER

GASKET

MT138A SEP 95

Moen Incorporated

Printed in U.S.A.

Consumer Information

Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed to stand in contact

with the brass. The amount of lead contributed by any faucet is highest when the faucet is new. The following steps may

reduce potential exposure to lead from faucets and other parts of the plumbing system:

• Always run the water for a few seconds prior to use for drinking or cooking.

• Use only cold water for drinking or cooking.

• If you wish to flush the entire plumbing system of water that has been standing in the pipes or other fittings, run the

cold water until the temperature of the water drops, indicating water coming from the outside main.

• If you are concerned about lead in your water, have your water tested by a certified laboratory in your area.

HELPLINE:

For answers to any product, installation,

replacment parts or warranty questions,

call our consumer helplines.

In the U.S., toll free:

1-800-321-6636

In Canada call:

Toronto, 905-829-3400

Rest of Canada, 1-800-465-6130

Moen Incorporated 25300 Al Moen Drive, North Olmsted, OH 44070-8022, U.S.A.

In Canada:

Moen Inc. 2816 Bristol Circle, Oakville, Ontario L6H5S7



Moen 8410 User manual

Brand: Moen

Model: 8410

Category: Sanitary ware

Type: User manual

This manual is also suitable for

Download PDF

report

Moen 8410 User manual

This manual is also suitable for

Moen 8410 User manual

Related papers

Other documents