IKEA HOO D10 S User guide

5019 618 33050/B

INSTALLATION AND USE

For installation: The hood must be installed at least 50 cm from electric cookers and 65 cm from gas, gas oil or coal

cookers. If the installation instructions for a gas cooker specify a greater distance, then this distance must be observed.

For installation and use: Before installing or using the hood, read this manual carefully. The drawings are at the

front of the manual. The Manufacturer declines all liabillity for any faults, damage or fires caused by the appliance

as a result of failure to observe the instructions and recommendations given in this manual.

Contact a qualified technician for installation.

GB

5019 618 33050/B

____________________________________________________________________________

5019 618 33050/B

INSTALLATION AS AN EXTRACTOR OR FILTER HOOD

Important: the figures are on the first pages of this booklet.

• Fix the bracket on the rear of the hood near the coupling ring (Fig. 1.1a).

Note: the bracket can be adjusted horizontally, which enables the position of the hood to be adjusted (Fig. 1.1b).

• Trace a centre line on the wall between the hob and ceiling (Fig. 2.2).

Mark the distance from the hob (respecting the minimum distance) with the pencil and position the template (if provided)

against the wall on the mark (Fig. 2.3).

Then mark and drill the hole, insert the wall plug and partially tighten 1 screw (Fig. 2.4).

• Fix the flue support as close as possible to the ceiling (Fig. 3.1). For filter operation, in this phase, also fix the deflector

(Fig. 3.2).

Hang the hood on the partially tightened screw (Fig. 3.3a - if necessary, adjust the hood horizontally by means of the

bracket - Fig- 3.3b)

Mark the hood fixing points:

2 at the bottom: remove the grease filters (Fig. 3.4), 2 at the top on the sides of the bracket.

Remove the hood, drill the holes, insert the plugs into the holes (Fig. 3.5), refit the hood, insert and tighten all the screws

(Fig.3.6 - Fig. 3.7)

External Exhaust Mode: Fumes are extracted and expelled to the outside through a fume hose fixed to the collar at the top

of the hood.

Caution! If the hood is equipped with a carbon filter, this must be removed.

Exhaust air must not be conveyed through a flue used for removal of fumes produced by gas combustion appliances or other

combustible materials, but must have an independent outlet. All national regulations governing extraction of fumes must be

observed.

Filter Hood: Air is filtered through a carbon filter and returned to the room.

Caution! If the hood is not already equipped with a carbon filter, one must be ordered and fitted prior to use.

Installing the telescopic flue

• Connect the hood to the mains supply and fix the telescopic flue to the flue bracket with two screws. Slide the bottom

section down into its seat on the top of the hood (Fig. 4).

GB

5019 618 33050/B

1. Control panel.

Light :

move the switch to the right or press the button to switch

on.

Extraction speed :

move the switch to the right or press the next button to

increase extraction speed (or open the shutter ) .

2. Grease filters.

3. Lamp covers(or halogen lamps, depending on the

model).

4. Telescopic flue.

Grease filters:

Metal grease filters have an unlimited

life and should be washed once a

month either by hand or in a

dishwasher at a low temperature and

in a short cycle. Washing in a

dishwasher can cause grease filters to

turn white, but this in no way affects

efficiency.

Press the handle to release the filter

Wash the filter and leave it to dry. Refit the filter in reverse

order.

Bulb/s:

Detach the lighting unit and remove

the burnt-out bulb.

Refit the filters.

Halogen bulbs:

Use a small screwdriver or any other

suitable tool to prise off the bulb cover.

Replace the bulb cover so that it clicks

into position.

Use only max 40 W

- E14 bulbs or max 20 W halogen

bulbs (depending on the model),

taking care not to touch them with

your hands.

Fitting or replacing the carbon filter

(filter hoods only).

Change the carbon filter every six months.

1. Remove the grease filters.

2. Fit the filters as shown in the figures below.

3. Reverse the above procedure to remove the carbon

filter.

4. Refit the grease filters.

CLEANING THE HOOD

Warning! Failure to remove oil and grease at least once a

month could lead to fire.

Use a soft cloth damped in a neutral detergent. Never use

abrasives or alcohol.

BEFORE USING THE HOOD

Please read these instructions carefully in order to get the

best out of your new hood.

Packaging materials can be dangerous for children. Keep

packaging materials (plastic bags, polystyrene, etc.) well out

of their reach.

Make sure the hood has not been damaged during transport.

Installation and electrical connections must be carried out by

a qualified technician in compliance with local safety

regulations.

1

4

3

2

a

b

CLACK!

2.

1.

GB

5019 618 33050/B

Electrical connection

The mains voltage must match that given on the rating plate

located inside the hood. If provided with a plug, connect the

hood to a socket complying with the current regulations and

located in an accessible area. If it does not have a plug (direct

connection to the power supply) or if the plug is not in an

accessible place, fit a suitable double-pole switch that ensures

complete disconnection from the power supply in category III

overvoltage conditions, complying with the installation rules.

WARNING: Before reconnecting the hood circuit to the

power supply and checking correct operation, always make

sure the power cable is correctly fitted and that it was NOT

crushed in its housing during installation. Make sure to have

this operation carried out by a specialised technician.

Cleaning the hood

WARNING: Failure to remove oil/grease (at least once a

month) could result in fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

Please read these instructions carefully and keep them for

future reference, in order to ensure best use of your hood.

The packing materials (plastic bags, polystyrene, etc.) are a

potential source of danger and must be kept out of the reach

of children.

Make sure the hood has not been damaged during transport.

Declaration of conformity

This product has been designed, manufactured and put on

the market in conformity with:

- safety objectives of the “Low Voltage” Directive

2006/95/EC (which replaces 73/23/EEC as amended)

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

If the hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

If the hood is not extracting enough:

• Is the right speed selected?

• Do the filters need cleaning or replacing?

• Are the air outlets blocked?

If the lamp does not work:

• Does the lamp need replacing?

• Is the lamp correctly fitted?

AFTER-SALES SERVICE

Before calling the After-Sales Service

1. Check to see if you can fix the problem yourself

(see “Troubleshooting Guide”).

2. Switch the appliance off and then on again to check if the

problem has been eliminated.

3. If the problem persists, contact the After-Sales Service.

Specify:

• the type of fault,

• the product model given on the dataplate inside the

hood, visible on removing the grease filters,

• your full address,

• your telephone number and area code,

• the Service code (the number under the word SERVICE

on the dataplate inside the hood, behind the grease

filter).

If any repairs are necessary, contact an authorised Service

Centre (to ensure the use of original spare parts and correct

repair).

Failure to comply with these instructions can compromise

the safety and quality of the product.

GB

IKEA HOO D10 S User guide

IKEA HOO D10 S User guide

Related papers

Other documents