Page is loading ...
01
Backup Keys (2)
Owner’s Manual/Quick Start Guide
Hardware Mounting Kit
Wire rope
External battery
Owner’s
Manual
#
02
To prevent damage to your safe unit or injury to yourself or to others, read the following safety precautions
before using this unit.
Neither seller nor manufacturer shall be liable for unauthorized access, any injury, loss or damage to
personal property direct or consequential, arising out of the use of, or the inability to use the Safe.
The user shall determine the suitability of the Safe before the intended use and user assumes all risk and
liability what soever in connection therewith, Safe are not intended to protect against environmental hazards
including fire and water.
Be sure and follow all local and state firearm laws.
DO NOT operate a firearm without proper training and experience.
03
Use the NEW AA alkaline batery. Using other batteries
may cause unusable conditions.
Your safe will automatically lock when you
fully close
the lid.
Toget started, remove the key cover (see Figure C),
and insert one of your backup keys into the keyhole
at the front of the safe. Push key in and rotate the
key counterclockwise to open the safe.
Remove crate foam insert. Locate the battery
compartment door on the inside of the safe directly
below the keypad (see Figure D).
Open the battery cover and insert the 4 AA alkaline
batteries (notincluded) into the battery compartment.
Note that pay attention to the “+“ and “-“ signs. The “-”
end of the batteries go against the spring inside of the
compartment.
After inserting the battery,Place the batteries cover
.
You are now ready to program your safe.
Ifthepasswordcontactisenteredincorrectly3timesorthefingerprint isenteredincorrectly5 consecutivetimes,
the
panel
wil
l
be
lock
ed
f
or
1
minut
e
,
the
buzz
er
wil
l
alarm
f
or
30
seconds
,
and
al
l
k
e
y
s
/
fingerprin
ts
wil
l
bec
ome
invalid during the alarm period;
Note:The buzzeralarms for30 secondswill notbe affectedbythe silence,but will still sound
Programming a new code will overwrite your previous code.
Enter default code 1-2-3-4-# on the keypad to open your safe.
With the safe open, press and hold the "PROGRAM" button
(3 seconds), all keys (1-#) will light up twice with double beep
(see Figure E).
Directly enter the 3-6 digits of the new password. and press"#"key.
If you hear 2 beeps and the green light flashes twice, If the
password setting is successful; if you hear 3 beeps and the red
light flashes 3 times, the password setting is failed , Please
start over from the second step.
04
FIGURE E
If the entry fails, the buzzer will beep 3 times and the red
light will flash 3 times; if no finger is pressed for more than
10 seconds, the buzzer will beep 3 times and the red light will
flash 3 times, prompting the entry failure.
05 /
With the safe open, press and hold the “PROGRAM” button (3 seconds), all keys will light up once
with the one beep(see Figure F).
Using the helpful programming tips provided on page 6(see Fiure G) place your finger on the
fingerprint scanner for the 1st of four scans. Remove your finger after all keys light up GREEN
once with one short beep. Place finger again over the scanner until all keys light up GREEN once
with one short beep and lift.You will repeat this process until all keys light up twice with the
double beeps.
Now your fingerprint has been successfully registered. Close door and test to see if the safe will open
using your fingerprint. If you make a mistake and the new fingerprint will not work, you must repeat
the above steps.
FIGURE G
#
Helpful Programming TIPS:
1
Place your finger on the center of the scanner (this allows the scanner to read where most of the
fingerprint detail is located).
2
Adjust your finger slightly between scans for increased accuracy.
3
Excessive moisture, lotions, or dirt will affect your fingerprint and may Cause inaccurate sensor reading.
4 If you are experiencing difficulty try different fingers. Each finger is unique, and some fingers such as
your thumb, Contain more readable information than others.
5 To increase your success rate, please register the same fingerprint multiple times.
06
07 /
Press and hold the program button (5-6 seconds) until all the keys flash twice with double beeps
and let go.
Now all registered fingerprints are erased.(All fingerprint can open)
Tosilence the audible sound of the electronic,hold the"4"button for 4seconds until you hear one beep
and all keys will flash together.To unmute the keys,repeat this step.
If all keys will light up red 10 times with 10 times beeps when opening the safe by electronic way,your
battery level is critically low and your safe needs to be replaced the 4 new batteries.
There aresome mounting screwsincluded to mount your safe to a flat surfaceusing the pre-drilled
holes on the bottom.
08
09 /
Wire rope installation
With the safe open,
Take the A pass through the circle B and will form the big circle C,
then put the A to the Safe box
Then close the safe box
A B
If you have a problem with your safe that is not answered in the this manual, we encourage you to email
We will get back to you within 24hrs.
C
B
A
Oursafe is committed tobuilding highquality products and will makeevery efforttoensure our productsare free
from any defects. We guarantee your safe will be free of defects in materials or workmanship for a
period of one year from the date of original. This warranty does not cover abuse, misuse, use in any
manner for which is not designed, neglect, modification, damage in advertently caused by the owner;
accidents, and/or tampering.
If you safe is determined to be defective and we are responsible for the cause we will have it repaired at
our expense, or we will send a new replacement at no cost to you. You will be required to return your
existing unit as well as all included accessories to safe prior to replacement of the defective unit alongwith
your order of purchase.
If it is determined your safe needs to be returned our customer support team will provide you with a return
detail.
Please have the following information available when contacting US:
•
Purchaser’s name and mailing address, email address, and phone number
•
Online order number
•
Detailed description of problem
NEITHER SELLER NOR MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT OR
CONSEQUENTIAL, ARISING OUT OF THE USE OF,OR THE INABILITY TO USE our SAFE.
Dear Customer
Thank for your business
BEST WISHES FOR YOU
RNFSAFE delivers security exactly where you want it
/
