HealTech Electronics GPAT-K01 Installation guide

Brand
HealTech Electronics
Model
GPAT-K01
Type
Installation guide
GPAT-K01_InstallGuide_en.pdf [rev. 002] - 1 -
www.healtech-electronics.com
GIpro ATRE G2
Install Guide for GPAT-K01
Before installing this product, please make sure you got the right part for your bike.
See the part number on the packaging and use the Product Advisor on our
website to check compatibility.
These instructions are applicable to a wide range of motorcycles and describe the
main install steps needed for a successful installation. You can find motorcycle
specific Supplementary Manuals on our website. Please visit:
www.healtech-electronics.com/ATRE
Disclaimer: Do not attempt to install the product if you don’t have basic mechanical
skills. HealTech Electronics Ltd. and its distributors shall not be liable for any loss or
damage caused by improper installation. If in doubt, please consult with your
dealer.
Before you connect the GIpro harness to the bike’s wiring harness, install the
supplied 3-pole plug adapters as per this document. Installing the plug adapters is
simple and reversible process. No need to cut or splice any wires. Please follow the
install steps below.
1. Gain access to the Gear Position Switch (GPS) connector.
a) ZX-10R (2004-2005):
- Remove the seat, fuel tank and airbox.
- Locate the 4-pole green connector behind the second throttle body
from the left, under the fuel rail.
b) ZX-14 / ZZR1400 (2006-2015), Concours 14 / 1400GTR (2008-2016):
- Remove the seat and the three body panels around the fuel tank
(left & right grills, left inside fairing cover).
- Locate the 4-pole green connector at the left side, above the front
sprocket cover.
2. Disconnect the GPS coupler. You may need a small flat head
screwdriver to get the coupler apart.
Make sure the gearbox is in Neutral and turn the ignition switch ON.
Wait a few seconds. The Neutral indicator should NOT be lit with
disconnected GPS coupler. After confirming this, turn the ignition OFF
and proceed to the next step.
- 2 –
3. Hold the smaller 4-pole green plug facing you, with the locking
latch on top. Release two female terminals out of the four:
- Green with Red stripe
- Black
To release a terminal, raise the plastic lock pin above the terminal
with a small flat head screwdriver and pull the wire out GENTLY
through the back.
4. Insert the two female terminals (which you released in the
previous step) into the smaller 3-pole plug adapter supplied
through the back until they click into place. The diagram below shows
the lead orders with the front of the plug facing you:
Red
(
pre-installed)
Black
G
reen w
/
Red strip
e
5. Hold the larger 4-pole green plug facing you, with the locking
latch on top. Release two male terminals out of the four:
- Green with Red stripe
- Black, Black/Yellow or Black/Blue
To release a terminal, raise the plastic lock pin above the terminal
with a small flat head screwdriver and pull the wire out GENTLY
through the back.
6. Insert the two male terminals (which you released in the previous
step) into the larger 3-pole plug adapter supplied through the
back until they click into place. The diagram below shows the lead
orders with the front of the plug facing you:
B
lack
,
Black/Yellow or Black/Blue
G
reen w
/
Red stripe
7. Reconnect the 4-pole green connector.
8. Connect the GIpro plugs to the 3-pole plug adapters.
- 3 –
9. Neatly route the GIpro cable from the plugs to the mounting
location, preferably along the frame. Do not route the harness very
close to the exhaust pipe or cylinder head.
10. Connect the GIpro Red wire to an ignition switched +12V power
lead by using the Red wire tap connector supplied.
Usage: Place the unstripped bike wire (switched +12V) inside the run
channel. Close the side cover until latched. Cut off the excess length,
then insert the unstripped tap wire (GIpro Red) completely and check
its position. Insert the blade (u-contact) and press down by finger
pressure. Then, fully depress the u-contact with pliers. Close the
hinged top cover until latched.
The power must be ON even when the engine run switch is switched
off. We recommend tapping the Brown wire (on the ZZR1400 2012+
models only, tap the Blue wire) at the 2-pole rear brake light
switch connector.
11. Clean the mounting surface with soft cloth. Peel off the green plastic
from the back of the unit and mount the display (apply pressure for
about 10 seconds). Alternatively, you may use the extra sticky pad
(supplied) to mount the display to the side of the dashboard.
Note: The GIpro unit is programmed via the Touch Sensor located at
the top side of the unit. If this area is not accessible after mounting,
program the unit before mounting. Refer to the User’s Guide.
12. Secure the cable with the cable ties (supplied) starting from the
display to the plugs, ensuring that the steering movement is not
restricted by the cable. Do not allow direct contact between the
engine (cylinder block) and the harness.
13. Make sure that all connectors and hoses are in place under the
fuel tank while lowering the tank.
14. Turn the ignition ON, have the engine stop switch in RUN position,
and put the side-stand in upright position. The display should count
up and then indicate the actual gear (“0” in neutral).
If the display does not light up, disconnect the connectors and check
whether the connector pins are bent or pushed out of position. Spray
some contact cleaner into the plugs. Check that the GIpro red wire
gets +12V.
15. Secure the fuel tank and install the seat.
16. When the installation is complete, refer to the User’s Guide for
instructions.
Note: If the unit does not indicate the gears correctly with the pre-set
gear position values, you’ll need to start the Learning procedure.
  • Page 1 1
  • Page 2 2
  • Page 3 3

HealTech Electronics GPAT-K01 Installation guide

Brand
HealTech Electronics
Model
GPAT-K01
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents