MULTIQUIP DCa70ssJU4i Specification

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To ﬁnd the latest revision of this

publication, visit our website at:

www.mqpower.com

®

WHISPERWATT™ SERIES

MODEL DCA70SSJU4i

60Hz GENERATOR

(JOHN DEERE 4045HFG92 DIESEL ENGINE)

PARTS LIST NO. M2871300004

Revision #2 (04/09/14)

OperatiOn and parts Manual

PAGE 2 — DCA70SSJU4i

PROPOSITION 65 WARNING

Diesel engine exhaust and some of

DCA70SSJU4i 

REPORTING SAFETY DEFECTS

If you believe that your vehicle has a defect that could cause a crash or could

cause injury or death, you should immediately inform the National Highway

Trafﬁ c Safety Administration (NHTSA) in addition to notifying Multiquip Inc. at

1-800-421-1244.

If NHTSA receives similar complaints, it may open an investigation, and if it

ﬁ nds that a safety defect exists in a group of vehicles, it may order a recall and

remedy campaign. However, NHTSA cannot become involved in individual

problems between you, your dealer, or Multiquip Inc.

To contact NHTSA, you may either call the Vehicle Safety Hotline toll-free

at 1-888-327-4236 (TTY: 1-800-424-9153), go to http://www.safercar.gov; or

write to:

Administrator

NHTSA

400 Seventh Street, SW.,

Washington, DC 20590

You can also obtain information about motor vehicle safety from

http://www.safercar.gov.

PAGE 4 — DCA70SSJU4i

TABLE OF CONTENTS

DCA70SSJU4i 60 Hz

Generator

Proposition 65 Warning ........................................... 2

Reporting Safety Defects ......................................... 3

Table Of Contents .................................................... 4

Safety Information .............................................. 6-11

Generator/Engine Speciﬁcations ........................... 12

Generator Dimensions ........................................... 13

Trailer Dimensions/Speciﬁcations .......................... 13

Installation ........................................................ 16-17

General Information ............................................... 18

Generator Major Components ............................... 19

Trailer Major Components ..................................... 20

Engine Control Unit (ECU) .................................... 21

Engine/Generator Control Panel............................ 22

Output Terminal Panel Familiarization .............. 23-25

Load Application .................................................... 26

Generator Outputs ................................................. 27

Generator Outputs/Gauge Reading ....................... 28

Output Terminal Panel Connections ................. 29-30

600 VAC Connections (Option) .............................. 31

Inspection/Setup ............................................... 32-35

Generator Start-Up Procedure (Manual Mode) 36-37

Generator Start-Up Procedure (Auto Mode) .......... 38

Generator Shut-Down Procedures ........................ 39

Generator/Engine Maintenance ........................ 40-46

Trailer Maintenance .......................................... 47-49

Trailer Guidelines .............................................. 50-64

Troubleshooting Diagnostics ................................. 66

Troubleshooting Generator ................................... 67

Troubleshooting Engine .................................... 68-69

Generator Wiring Diagram ..................................... 70

600 VAC Auto Transformer Wiring Diagram (Option) .. 71

Engine Wiring Diagram .......................................... 72

Battery Charger Wiring Diagram (Option) ............. 73

Water Heating Element Wiring Diagram (Option) .. 74

Explanation Of Code In Remarks Column............. 75

Suggested Spare Parts ......................................... 77

Component Drawings

Generator Assembly ......................................... 78-79

Control Box Assembly ...................................... 81-83

Engine And Radiator Assembly ........................ 84-87

Output Terminal Assembly ................................ 88-89

Battery Assembly ............................................. 90-91

Mufﬂer Assembly ............................................. 92-93

Fuel Tank Assembly .......................................... 94-95

Enclosure Assembly ......................................... 96-99

Rubber Seals Assembly ............................... 100-101

Camlock Assembly ....................................... 102-103

Battery Charger Assembly............................ 104-105

Heating Element Assembly .......................... 106-107

3-Phase 600 VAC Transformer Assembly ..... 108-109

Trailer Assembly (TRLR70USH) ................... 110-111

Trailer Assembly (TRLR70USE) ................... 112-113

Nameplate And Decals Assembly ................ 114-117

Terms And Conditions Of Sale — Parts .............. 118

NOTICE

Speciﬁcations are subject to change without notice.

DCA70SSJU4i 

NOTES

PAGE 6 — DCA70SSJU4i

SAFETY INFORMATION

Do not operate or service the equipment before reading the

entire manual. Safety precautions should be followed at all

times when operating this equipment. Failure to read and

understand the safety messages and operating instructions

could result in injury to yourself and others.



The four safety messages shown below will inform you

about potential hazards that could injure you or others. The

safety messages speciﬁ cally address the level of exposure

to the operator and are preceded by one of four words:



or 



DANGER

Indicates a hazardous situation which, if not avoided,

 result in DEATH or 



Indicates a hazardous situation which, if not avoided,

 result in DEATH or 



Indicates a hazardous situation which, if not avoided,

 result in  or 

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this

equipment will be referenced with hazard symbols which

may appear throughout this manual in conjunction with

safety messages.

DCA70SSJU4i 

SAFETY INFORMATION







 operate this equipment without proper protective

clothing, shatterproof glasses, respiratory protection,

hearing protection, steel-toed boots and other protective

devices required by the job or city and state regulations.



 operate this equipment when not

feeling well due to fatigue, illness or when

under medication.



 operate this equipment under the inﬂ uence of

drugs or alcohol.



 check the equipment for loosened threads or

bolts before starting.



DO NOT use the equipment for any purpose other than

its intended purposes or applications.

NOTICE



This equipment should only be operated by trained and

qualiﬁ ed personnel 18 years of age and older.



Whenever necessary, replace nameplate, operation and

safety decals when they become difﬁ cult read.



Manufacturer does not assume responsibility for any

accident due to equipment modiﬁ cations. Unauthorized

equipment modiﬁ cation will void all warranties.

  use accessories or attachments that are not

recommended by MQ Power for this equipment. Damage

to the equipment and/or injury to user may result.

  know the location of the nearest



 know the location of the nearest



  know the location of the nearest

phone or 

Also, know the

phone numbers of the nearest ambulance, doctor

and



This information will be invaluable in

the case of an emergency.

GENERATOR SAFETY

DANGER

  operate the equipment in an explosive

atmosphere or near combustible materials. An

explosion or ﬁ re could result causing severe





  disconnect any



These devices are intended for operator safety.

Disconnection of these devices can cause severe injury,

bodily harm or even death. Disconnection of any of these

devices will void all warranties.



 

lubricate components or attempt service on a

running machine.

NOTICE

 

ensure generator is on level ground before use.

  keep the machine in proper running condition.



Fix damage to machine and replace any broken parts

immediately.

 

store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children and unauthorized personnel

PAGE 8 — DCA70SSJU4i

SAFETY INFORMATION



DANGER



The engine fuel exhaust gases contain poisonous carbon

monoxide. This gas is colorless and odorless, and can

cause death if inhaled.



The engine of this equipment

requires an adequate free

ﬂ ow of cooling air. 

operate this equipment in

any enclosed or narrow area

where free ﬂ ow of the air is

restricted. If the air ﬂ ow is

restricted it will cause injury to people and property and

serious damage to the equipment or engine.





DO NOT place hands or fingers inside engine

compartment when engine is running.



 operate the engine with heat shields or

guards removed.



Keep ﬁ ngers, hands hair and clothing away

from all moving parts to prevent injury.



DO NOT remove the radiator cap while the

engine is hot. High pressure boiling water

will gush out of the radiator and severely

scald any persons in the general area of

the generator.



DO NOT remove the coolant drain plug while the engine

is hot. Hot coolant will gush out of the coolant tank and

severely scald any persons in the general area of the

generator.



DO NOT remove the engine oil drain plug while the

engine is hot. Hot oil will gush out of the oil tank and

severely scald any persons in the general area of the

generator.





 touch the hot exhaust manifold,

mufﬂ er or cylinder. Allow these parts to cool

before servicing equipment.

NOTICE

 

run engine without an air ﬁ lter or with a dirty air

ﬁ lter. Severe engine damage may occur. Service air ﬁ lter

frequently to prevent engine malfunction.

  tamper with the factory settings

of the engine or engine governor. Damage

to the engine or equipment can result

if operating in speed ranges above the

maximum allowable.



Wet stacking is a common problem with diesel engines

which are operated for extended periods with light or

no load applied. When a diesel engine operates without

sufﬁ cient load (less than 40% of the rated output), it will

not operate at its optimum temperature. This will allow

unburned fuel to accumulate in the exhaust system,

which can foul the fuel injectors, engine valves and

exhaust system, including turbochargers, and reduce

the operating performance.

In order for a diesel engine to operate at peak efﬁ ciency,

it must be able to provide fuel and air in the proper ratio

and at a high enough engine temperature for the engine

to completely burn all of the fuel.

Wet stacking does not usually cause any permanent

damage and can be alleviated if additional load is

applied to relieve the condition. It can reduce the system

performance and increase maintenance. Applying an

increasing load over a period of time until the excess

fuel is burned off and the system capacity is reached

usually can repair the condition. This can take several

hours to burn off the accumulated unburned fuel.



State Health Safety Codes and Public Resources

Codes specify that in certain locations, spark arresters

must be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed

to prevent accidental discharge of sparks or ﬂ ames

from the engine exhaust. Spark arresters are qualiﬁ ed

and rated by the United States Forest Service for this

purpose. In order to comply with local laws regarding

spark arresters, consult the engine distributor or the

local Health and Safety Administrator.

DCA70SSJU4i 

SAFETY INFORMATION



DANGER



DO NOT start the engine near spilled fuel or combustible

ﬂ uids. Diesel fuel is extremely ﬂ ammable and its vapors

can cause an explosion if ignited.



 refuel in a well-ventilated area, away from

sparks and open ﬂ ames.



 use extreme caution when working with

ﬂ ammable liquids.



DO NOT ﬁ ll the fuel tank while the engine is running

or hot.



DO NOT overﬁ ll tank, since spilled fuel could ignite if it

comes into contact with hot engine parts or sparks from

the ignition system.



Store fuel in appropriate containers, in well-ventilated

areas and away from sparks and ﬂ ames.



 use fuel as a cleaning agent.



DO NOT smoke around or near the

equipment. Fire or explosion could result

from fuel vapors or if fuel is spilled on a

hot engine.







Check with your local county or state safety

towing regulations, in addition to meeting

Department of Transportation (DOT)

Safety Towing Regulations, before towing

your generator.



Refer to MQ Power trailer manual for additional safety

information.



In order to reduce the possibility of an accident while

transporting the generator on public roads, 

make sure the trailer that supports the generator and

the towing vehicle are mechanically sound and in good

operating condition.



shutdown engine before transporting

 Make sure the hitch and coupling of the towing vehicle

are rated equal to, or greater than the trailer “gross

vehicle weight rating.”

 inspect the hitch and coupling for wear.



tow a trailer with defective hitches, couplings, chains, etc.



Check the tire air pressure on both towing vehicle and

trailer.

Trailer tires should be inﬂ ated to 50 psi cold.

Also check the tire tread wear on both vehicles.

 make sure the trailer is equipped with a

safety



  properly

attach trailer’s safety chains to towing

vehicle.

 

make sure the vehicle and trailer directional,

backup, brake and trailer lights are connected and

working properly.

 DOT Requirements include the following:

 •Connectandtestelectricbrakeoperation.

 •Secure portablepowercablesin cable tray withtie

wraps.

 The maximum speed for highway towing is 

unless

posted otherwise. Recommended off-road towing is not to

exceed  or less depending on type of terrain.



Avoid sudden stops and starts. This can cause skidding,

or jack-kniﬁ ng. Smooth, gradual starts and stops will

improve towing.

 Avoid sharp turns to prevent rolling.



Trailer should be adjusted to a level position at all times

when towing.



Raise and lock trailer wheel stand in up position when

towing.

 Place chock blocks underneath wheel to prevent

rolling

while parked.

 Place support blocks

underneath the trailer’s bumper

to prevent tipping while parked.



Use the trailer’s swivel jack to adjust the trailer height to

a level position while parked.

i

SAFETY INFORMATION



DANGER



DO NOT touch output terminals during

operation. Contact with output terminals

during operation can cause electrocution,





The electrical voltage required to

operate the generator can cause severe

injury or even death through physical contact with live

circuits. Turn generator and all circuit breakers OFF

before performing maintenance on the generator or

making contact with output terminals.



 insert any objects into the output

receptacles during operation. This is

extremely dangerous. The possibility exists

of electrical shock, electrocution or





Backfeed to a utility system can cause

electrocution and/or property damage.

connect the generator to a

building’s electrical system without

a transfer switch or other approved

device. All installations should be

performed by a licensed electrician in accordance with

all applicable laws and electrical codes. Failure to do so

could result in electrical shock or burn, causing serious





DANGER



 let power cords or cables 



  while AC power from the

generator is being transferred to a load.



 use damaged or worn cables or cords when

connecting equipment to generator. Inspect for cuts in

the insulation.



 grab or touch a live power

cord or cable with wet hands. The

possibility exists of electrical shock,



 Make sure power cables are securely connected to the

generator’s output receptacles. Incorrect connections

may cause electrical shock and damage to the

generator.

NOTICE

 

make certain that proper power or extension

cord has been selected for the job. See Cable Selection

Chart in this manual.

Grounding Safety

DANGER

 

make sure that electrical circuits are properly

grounded to a suitable earth ground (ground rod) per

the National Electrical Code (NEC) and local codes

before operating generator.

Severe injury or death by

electrocution

can result from operating an ungrounded

generator.

  use gas piping as an electrical ground.



DANGER

 DO NOT

drop the battery. There is a possibility that the

battery will explode.

 DO NOT expose the battery to open ﬂ ames,

sparks, cigarettes, etc. The battery contains

combustible gases and liquids. If these

gases and liquids come into contact with a

ﬂ ame or spark, an explosion could occur.



  wear safety glasses when

handling the battery to avoid eye irritation.

The battery contains acids that can cause

injury to the eyes and skin.

 Use well-insulated gloves when picking up the battery.

 

keep the battery charged. If the battery is not

charged, combustible gas will build up.

 

recharge the battery in a well-ventilated

environment to avoid the risk of a dangerous concentration

of combustible gasses.

DCA70SSJU4i 

SAFETY INFORMATION

 If the battery liquid (dilute sulfuric acid) comes into

contact with clothing or skin, rinse skin or clothing

immediately with plenty of water.



If the battery liquid (dilute sulfuric acid) comes into

contact with eyes, rinse eyes immediately with plenty

of water and contact the nearest doctor or hospital to

seek medical attention.





disconnect the 

before performing service on the generator.



keep battery cables in good working condition.

Repair or replace all worn cables.





NOTICE

Decommissioning is a controlled process used to safely

retire a piece of equipment that is no longer serviceable.

If the equipment poses an unacceptable and unrepairable

safety risk due to wear or damage or is no longer cost

effective to maintain (beyond life-cycle reliability) and is to

be decommissioned (demolition and dismantlement),be

sure to follow rules below.



DO NOT pour waste or oil directly onto the ground, down

a drain or into any water source.



Contact your country's Department of

Public Works or recycling agency in your

area and arrange for proper disposal of

any electrical components, waste or oil

associated with this equipment.



When the life cycle of this equipment is over, remove

battery and bring to appropriate facility for lead

reclamation. Use safety precautions when handling

batteries that contain sulfuric acid.



When the life cycle of this equipment is over, it is

recommended that the trowel frame and all other metal

parts be sent to a recycling center.

Metal recycling involves the collection of metal from

discarded products and its transformation into raw

materials to use in manufacturing a new product.

Recyclers and manufacturers alike promote the process

of recycling metal. Using a metal recycling center

promotes energy cost savings.



NOTICE

The diesel engine used in this equipment has been

designed to reduce harmful levels of carbon monoxide

(CO), hydrocarbons (HC) and nitrogen oxides (NOx)

contained in diesel exhaust emissions.

This engine has been certiﬁ ed to meet US EPA Evaporative

emissions requirements in the installed conﬁ guration.

Attempting to modify or make adjustments to the engine

emission system by unauthorized personnel without proper

training could damage the equipment or create an unsafe

condition.

Additionally, modifying the fuel system may adversely affect

evaporative emissions, resulting in ﬁ nes or other penalties.



The emission control label is an integral part of the emission

system and is strictly controlled by regulations.

The label must remain with the engine for its entire life.

If a replacement emission label is needed, please contact

your authorized engine distributor.

i

GENERATOR/ENGINE SPECIFICATIONS

Generator Speciﬁcations



DCA70SSJU4i

Type

Revolving ﬁeld, self ventilated,

open protected type synchronous generator

Armature Connection Star with Neutral Zigzag

Phase

3Ø 3Ø

Standby Output

61.6 kW (77 kVA) 44 kW

Prime Output

56 kW (70 kVA) 40 kW





208Y/120, 220Y/127, 240Y/139 N/A





416Y/240, 440Y/254, 480Y/277 N/A





N/A 240/120

Power Factor

0.8 1.0

Frequency

60 Hz

Speed

1800 rpm



Single Phase, 60 Hz



4.8 Kw (2.4 kW x 2)

Dry Weight

3,594 lbs. (1,630 kg)

Wet Weight

4,410 lbs. (2,000 kg)

Engine Speciﬁcations



John Deere 4045HFG92 Interim Tier 4

Type

Water-cooled, direct injection, turbo-charged

air cooled EGR



4 cylinders



4.17 in. x 5.00 in. (106 mm x 127 mm)

Displacement

275 cu. in. (4.5 liter)

Rated Output

97 HP at 1800 rpm

Starting

Electric

Coolant Capacity

5.9 gal. (22.4 liters)

1



3.9 gal. (14.7 liters)

2



API service class CJ-4 SAE 15W-40

Fuel Type

#2 Diesel Fuel (Ultra low sulfur diesel fuel only)



25.9 gal. (98 liters)

Fuel Tank Capacity

103 gal. (390 liters)

Fuel Consumption

4.3 gal. (16.2 L)/hr at full load 3.4 gal. (12.7 L)/hr at 

2.7 gal. (10.1 L)/hr at  2.0 gal. (7.4 L)/hr at 



27 (CCA 0°F 800A) X 1



Includes engine and radiator hoses

2

Includes ﬁlters

DCA70SSJU4i 

GENERATOR DIMENSIONS

Generator Dimensions

Reference



  

A 39.25 (997) E 39.25 (997)

B 32.80 (883) F 105.12 (2,670)

C 39.25 (997) G 68.30 (1,735)

D 32.28 (820) H 37.40 (950)

Figure 1. Dimensions

i

TRAILER DIMENSIONS/SPECIFICATIONS

Figure 2. Trailer Dimensions

D

C

B

A

G

F

E

TOP VIEW

SIDE VIEW

Trailer Dimensions

Reference



  

A 169.4 (4,938) E 24.2 (615)

B 47.5 (1,207) F 20.2 (513)

C 60 (1,524) G 20.35 (517)

D 72.5 (1,842)



Gross Vehicle Weight Rating (GVWR) 7,000 lbs. (3,175 kg)

Gross Axle Weight Rating (GAWR) Each 3,500 lbs. (1,588 kg)

Actuator Rating 8,000 lbs. (3,629 kg)

Coupler Types

Adjustable 2-inch Ball Coupler

Adjustable 2-5/16-inch Ball Couple

Adjustable 3-inch Pintle-eye Coupler

Tire Size ST205/75D15 LR-C

Tire Load Rating 1,820 lbs./825 kg (ea.)

Wheel Bolt Pattern 5 Lug on 4.5 in.

Hydraulic Brakes (Standard) Hydraulic-actuated Drum Brakes (all axles)

Electric Brakes (Option) Electric-actuated Drum Brakes (all axles)

Bolt-on Electric Brake Coupler Plate Option

Electric Breakaway Safety Device electric-actuated brakes) Option

Tongue Mounted Swivel Jack (Standard) 3,000 lbs. (1,361 kg)

Tongue Bolt-On Jack (Option) 8,000 lbs. (3,629 kg) Option

Axle Tandem

Suspension Torsion

Lights

D.O.T. Approved Tail Lamps, Stop Lamps, Turn

Signal Lamps, Side Marker Lamps

Weight (Approximate) 960 lbs. (435 kg)

DCA70SSJU4i 

NOTES

i

INSTALLATION

Figure 3. Typical Generator Grounding Application

DCA70SSJU4i 

INSTALLATION



Install the generator in a area that is free of debris,

bystanders, and overhead obstructions. Make sure the

generator is on secure level ground so that it cannot slide

or shift around. Also install the generator in a manner so

that the exhaust will not be discharged in the direction of

nearby homes.

The installation site must be relatively free from moisture

and dust. All electrical equipment should be protected from

excessive moisture. Failure to do will result in deterioration

of the insulation and will result in short circuits and

grounding.

Foreign materials such as dust, sand, lint and abrasive

materials have a tendency to cause excessive wear to

engine and alternator parts.



Exhaust gases from diesel engines are extremely

poisonous. Whenever an engine is installed indoors the

exhaust fumes must be vented to the outside. The engine

should be installed at least two feet from any outside wall.

Using an exhaust pipe which is too long or too small can

cause excessive back pressure which will cause the engine

to heat excessively and possibly burn the valves.



The generator must be mounted on a solid foundation (such

as concrete) and set ﬁrmly on the foundation to isolate

vibration of the generator when it is running. The generator

must set at least 6 inches above the ﬂoor or grade level (in

accordance to NFPA 110, Chapter 5-4.1). DO NOT remove

the metal skids on the bottom of the generator. They are

to resist damage to the bottom of the generator and to

maintain alignment.



Pay close attention to ventilation when operating the

generator inside tunnels and caves. The engine exhaust

contains noxious elements. Engine exhaust must be

routed to a ventilated area.



To guard against electrical shock and possible damage to

the equipment, it is important to provide a good EARTH

ground (Figure 3).

Article 250 (Grounding) of the National Electrical Code

(NEC) provides guide lines for proper grounding and

speciﬁes that the cable ground shall be connected to the

grounding system of the building as close to the point of

cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following

grounding requirements:

1. Use one of the following wire types to connect the

generator to earth ground.

a. Copper - 8 AWG (5.3 mm

2

)

b. Aluminum - 6 AWG (8.4 mm

2

)

2. When grounding the generator (Figure 2) connect the

ground cable between the lock washer and the nut on

the generator and tighten the nut fully. Connect the

other end of the ground cable to earth ground.

3. NEC article 250-52(c) speciﬁes that the earth ground rod

should be buried a minimum of 8 ft. into the ground.

NOTICE

When connecting the generator to any buildings

electrical system  consult with a licensed

electrician.

NOTICE

This generator has a permanent bonding conductor

between the generator stator windings and the frame.

i

GENERATOR

This generator (Figure 4) is designed as a high quality

portable (requires a trailer for transport) power source for

telecom sites, lighting facilities, power tools, submersible

pumps and other industrial and construction machinery.



The “Operating Panel” is provided with the following:

 ECU Controller

 Gauge Unit Assembly

•Oil Pressure Gauge

•Water Temperature Gauge

•Charging Voltmeter

•Fuel Gauge

•Tachometer

 Panel Light/Panel Light Switch

 Hour Check Button

 Auto Start/Stop Switch

 Fuel Leak Detected Alarm Lamp



The “Control Panel” is provided with the following:

 Frequency Meter (Hz)

 AC Ammeter (Amps)

 AC Voltmeter (Volts)

 Ammeter Change-Over Switch

 Voltmeter Change-Over Switch

 Voltage Regulator

 3-Pole, 200 amp Main Circuit Breaker

 “Control Box” (located behind Control Panel)

•Automatic Voltage Regulator

•Current Transformer

•Over-Current Relay

•Starter Relay



The “Output Terminal Panel” is provided with the following:

 Three 120/240V output receptacles (CS-6369), 50A

 Three auxiliary circuit breakers, 50A

 Two 120V output receptacles (GFCI), 20A

 Two GFCI circuit breakers, 20A

 Eight output terminal lugs (3Ø power)

 Ground lug

 Battery Charger (Option)

 Water Heating Element (Option)

 Camlock Connector (Option)

 600 VAC Output, Auto-Transformer (Option)



Each generator is equipped with the state of the art 

Delta” excitation system. The open delta system consist

of an electrically independent winding wound among

stationary windings of the AC output section.

There are four connections of the open delta A, B, C and

D. During steady state loads, the power from the voltage

regulator is supplied from the parallel connections of A to

B, A to D, and C to D. These three phases of the voltage

input to the voltage regulator are then rectiﬁed and are the

excitation current for the exciter section.

When a heavy load, such as a motor starting or a short

circuit occurs, the automatic voltage regulator (AVR)

switches the conﬁguration of the open delta to the series

connection of B to C. This has the effect of adding the

voltages of each phase to provide higher excitation to the

exciter section and thus better voltage response during the

application of heavy loads.

The connections of the AVR to the AC output windings are

for sensing only. No power is required from these windings.

The open-delta design provides virtually unlimited excitation

current, offering maximum motor starting capabilities. The

excitation does not have a “ﬁxed ceiling” and responds

according the demands of the required load.



This generator is powered by a 4 cylinder, 4-cycle water

cooled, direct injection, turbocharged, air cooled and EGR

John Deere 4045HFG92 diesel engine. This engine is

designed to meet every performance requirement for the

generator. Reference Table 2 for engine speciﬁcations.

In keeping with MQ Power’s policy of constantly improving

its products, the speciﬁcations quoted herein are subject

to change without prior notice.



The electric governor system controls the RPMs of the engine.

When the engine demand increases or decreases, the

governor system regulates the frequency variation to ±.25%.



When electric power is to be provided to various tools or

loads at some distance from the generator, extension cords

are normally used. Cables should be sized to allow for

distance in length and amperage so that the voltage drop

between the generator and point of use (load) is held to

a minimum. Use the cable selection chart (Table 8) as a

guide for selecting proper extension cable size.

GENERAL INFORMATION

DCA70SSJU4i 

GENERATOR MAJOR COMPONENTS



 

1 Mufﬂer Assembly

2 Enclosure Assembly

3 Voltage Selector Switch Assembly

4 Generator Assembly

5 Output Terminal Assembly

6 Battery Assembly

7 Engine Assembly

8 Fuel Tank Assembly

9 Circuit Breaker Assembly

10 Auto Start/Stop Controller Assembly

11 Gauge Unit Assembly

12 Generator Control Panel Assembly

Figure 4. GeneratorMajor Components

PAGE 20 — DCA70SSJU4i

TRAILER MAJOR COMPONENTS

Figure 5. Trailer Major Components

1

2

3

4

5

7

6

8

9

10

11

Figure 5 shows the location of the trailer components and

the 600 VAC option. The function of each component is

described below:

1. — Voltage converter

transformer. Converts the generator's 3Ø, 480 output

voltage to 3Ø, 600 VAC.

2. Tongue Jackstand — Use this jackstand to support

the trailer tongue when attaching the generator to a

towing vehicle

3. — Attach the trailer's 2-5/16 inch

ball coupler or 3-inch pintle coupler to the towing vehicle.

Use only the speciﬁed ball diameter as indicated on

your coupler. Use of any other ball diameter will create

an extremely dangerous condition which can result in

separation of the coupler and ball or ball failure.

4. Safety Chain — Always attach safety chains to the

towing vehicle.  use the trailer with the safety

chain unattached. Make sure safety chains are crossed

when towing.

5. Side Reﬂectors — There are two amber reﬂectors

located on the side of the trailer. These reﬂectors provide

better visibility in dark conditions.

6. Tires — This trailer uses a ST205/75D15 LR-C

size

tire. Replace with only recommended tire size. 

operate the trailer with bad or worn tires.

7. — Place blocks (not included as part

of the generator package) under each trailer wheel to

prevent rolling.

8. — Before towing the generator, make

sure that this light is operational and is working correctly.

 use the trailer if this light is inoperative.

9. — This light illuminates the license plate.

Whenever towing of the generator is required, make sure

this light is operational.

10. — Before towing the generator, make

sure that this light is operational and is working correctly.

 use the trailer if this light is inoperative.

11. — Contains 70 amp

breaker for 600 VAC operation.

Page is loading ...

MULTIQUIP DCa70ssJU4i Specification

MULTIQUIP DCa70ssJU4i Specification

Related papers

Other documents