HDview HD-TVI User guide

HD-TVI
Brand
HDview
Model
HD-TVI
Category
Security cameras
Type
User guide

HDview HD-TVI is a high-definition surveillance camera that delivers stunning image quality and a wide range of features to enhance your security system. With its 1080p resolution, this camera captures sharp and detailed footage, allowing you to easily identify faces, objects, and license plates. The camera also features night vision capabilities, providing clear images even in low-light conditions. Additionally, the HDview HD-TVI supports motion detection and alarm output, enabling you to stay informed of any suspicious activity on your property.

HDview HD-TVI is a high-definition surveillance camera that delivers stunning image quality and a wide range of features to enhance your security system. With its 1080p resolution, this camera captures sharp and detailed footage, allowing you to easily identify faces, objects, and license plates. The camera also features night vision capabilities, providing clear images even in low-light conditions. Additionally, the HDview HD-TVI supports motion detection and alarm output, enabling you to stay informed of any suspicious activity on your property.

Overview
Installation
Cable Connection
1
2
3
2
1
Quick Start Guide
HD PTZ Camera
■ Please read this instruction carefully before using the product
and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the Ethernet connector. Then tighten the nut and
the main cover.
3
Please make sure the wall is strong enough to bear the dome camera’s
weight and the camera is powered off during installation.
This PTZ camera supports different ways of installation. Please select a
way to install as needed. The following instructions are for reference only.
1
udio input
3
4 Alarm input/output
5 DC12V Power jack
6 Ground
7 Lock Screw
8 Loudspeaker
9 Light Sensor
10 Microphone
11 Reset*
12 Memory Card Slot
Ethernet connector (PoE+)
2 MIC-A (3.5mm)
HP-Audio output (3.5mm)
Connecting Alarm Input/Output
Connect to
earth ground
1
2
3
4
5
6
7
8
ALARM
4 3 2 1
9
10
11 12
*Reset: After the camera is powered on, press and hold the reset button for more than 3s to reset to
the factory default settings.
ALARM
4 3 2 1
RJ 45
DC12V
1--ALM-
2--ALM-
3--ALM-
4--ALM-
GND
IN
OPEN
COM
ALARM_IN
ALARM_GND
ALARM_OPEN
ALARM_COM
ALARM
POWER
PE
Relay
The max. load of alarm output: 30VDC, 1A
Memory Card Installation
Insert a micro
SD card
1. Loosen the two screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
TF
Cover
Lock
Screw
Ceiling Mounting
1. Unscrew the lock screw and then
remove the adapter.
Adapter
2. Use three screws provided to
install the adapter to the ceiling.
3. Align the screw holes of the
adapter with the screws of the
mounting base and then secure
the PTZ camera and the adapter
by putting these screws into its
original position.
.
Mounting
Base
4. Adjust the PTZ camera position.
Note that the marked position
should be the front of the camera.
Mark
MENU
PTZ Camera
Network Cable Network Cable
Switch
Router Computer
4Network Connection
5 Preset Description
Here we take accessing IP camera via LAN for example.
● Access the camera through IP-Tool
① Make sure that the camera and the PC are connected via LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 .168 . 226 . 201
255 . 255 . 255 . 0
192 .168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3
Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet
Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as the
computer’s. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please enter the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the PTZ camera listed in the IP-Tool or manually enter
the IP address in the address bar of the web browser to connect the PTZ
camera. Then follow directions to download and install the plugin.
Enter the username and password in the login interface.
⑤
The default username is admin; the default password is 123456.
Call Preset
Call No.90 Preset Run trace 1
Run cruise 1
Run 2cruise
Run 3cruise
Run 4cruise
Enable random scan
Enable auto scan
Save the left scan endpoint
Save the right scan endpoint
Save the random scan start point
Call No.91 Preset
Call No.92 Preset
Call No.93 Preset
Call No.94 Preset
Call No.97 Preset
Call No.99 Preset
Save No.91 Preset
Save No.92 Preset
Save No.93 Preset
Save Preset
Name:
Password:
Stream Type:
Language
Remember me
admin
1920x1080 25fps
English
Password
Login
  • Page 1 1
  • Page 2 2

HDview HD-TVI User guide

HD-TVI
Brand
HDview
Model
HD-TVI
Category
Security cameras
Type
User guide

HDview HD-TVI is a high-definition surveillance camera that delivers stunning image quality and a wide range of features to enhance your security system. With its 1080p resolution, this camera captures sharp and detailed footage, allowing you to easily identify faces, objects, and license plates. The camera also features night vision capabilities, providing clear images even in low-light conditions. Additionally, the HDview HD-TVI supports motion detection and alarm output, enabling you to stay informed of any suspicious activity on your property.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents