Briggs & Stratton 020477-00 Owner's manual

Brand: Briggs & Stratton

Model: 020477-00

Category: High-pressure cleaners

Type: Owner's manual

$$ure

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association

(PWMA) standard PWI01 (Testing and Rating Performance of PressureWashers).

BRMGG$& STRATTONPOWER PROBUCT$ GROUP, LLC

MMLWAUKEE,WM$CONSMN,U.S.A. Manual No. 315264GS Revision-

Thank youfor purchasingthis quality-built Briggs & Stratton@ pressurewasher. We are pleasedthat you've placedyour

confidence in the Briggs & Stratton brand.When operatedand maintainedaccording to the instructions in this manual, your

Bdggs & Stratton pressure washer will provide manyyears of dependableservice.

Thismanual contains safety information to makeyou awareof the hazardsand risks associatedwith pressure washersand

how to avoidthem. BecauseBriggs & Stratton does not necessarily knowall the applicationsthis pressure washercould be

usedfor, it is important that you readand understandthese instructions thoroughly before attempting to stad or operatethis

equipment. Savethese original instructionsfar future reference.

This pressurewasher requiresfinal assembly before use. Referto the Assembly section of this manualfor instructions on

final assembly procedures.Follow the instructions completely.

Where te Find Us

Younever haveto lookfar to find Briggs & Stratton support and servicefor your pressure washer.Thereare thousands of

Briggs & Stratton authorized servicedealersworldwide who provide qualityservice. You canalso find the nearestAuthorized

Service Dealerinour dealerIocator map on the Internet at BRIGGSandSTRATTON.COM.

Pressul'e Washer

Model Number

Revision

Serial Number

Engine

Model Number

Type Number

Code Number

Date Purchased

BRIGGS& STRATTONPOWERPRODUCTSis a registered

trademark of Briggs & Stratton Corporation

Milwaukee, Wl, USA

2 BRIGGSandSTRATTON.COM

Table of Contents

Operation .................................... 12

PressureWasher Location..................................... 12

How to Stad Your PressureWasher ............................. 12

How to Stop Your PressureWasher ............................. 14

How to UseAccessory Tray.................................... 14

How to Use SprayTips ....................................... 15

Cleaningand Applying Detergent................................ 15

PressureWasher Rinsing ..................................... 16

CleaningDetergentSiphoning Tube.............................. 16

Automatic Cool Down System (Thermal Refiefl..................... 16

Maintenance .................................. 17

MaintenanceSchedule........................................ 17

PressureWasher Maintenance ................................ 17

Engine Maintenance.......................................... 19

After EachUse.............................................. 21

Winter Storage.............................................. 22

Long Term Storage .......................................... 22

Treubiesheeting ................................ 23

Warranties .................................... 24

PressureWasher OwnerWarranty............................... 24

Espa_ol Portugu_,s

OperatorSafety

Equipment Description

Read _hi$ ITlanuaJ carefuJJy and become familiar

withyourpressurewasher. Enowitsapplications,

its limitations,and any hazardsinvolved.

This pressurewasher operatesat 207 BAR(3,000 PSi) ata

flow rateof 10.6 liters (2.8 gallons) per minute. This high

quality residential system features 25.4 cm (10 in) wheels,

axialcam pump with stainless steelpistons, automatic cool

down system, detergent siphoning system, nozzleextension

with quick connect spray tips, heavy duty 9.1 m (30 ft.)

hose, and more.

Everyeffort has beenmadeto ensurethat information in this

manual is accurateand current. However,we reservethe

right to change,alter, or otherwise improve the product and

this document at anytime without prior notice.

Mmpertant Safety Mnfermatien

The manufacturer cannot possibly anticipateeverypossible

circumstance that might involve a hazard.Thewarnings in

this manual,andthe tags anddecals affixedto the unit are,

therefore, not all-inclusive, if you usea procedure, work

method or operatingtechnique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make surethat the

procedure, work method or operating technique that you

choose does not renderthe pressurewasher unsafe.

Safety Symbols and Meanings

Operator's Manual Toxic Fumes

SlipperySurface

Fall

ElectricalShock

Fluid Injection

Fire Kickback Projectile

Explosion

Moving Parts FlyingObjects ChemicalBurn Hot Surface

The safety alertsymbol indicatesa potential personal

injury hazard A signalword (DANGER,WARNING,or

CAUTION_s usedwith the alert symbol to designatea

degreeor levelol hazardseriousness.A safety symbol may

be usedto representthetype of hazard.Thesignal word

NOTICEis usedto addresspracticesnot relatedto personal

injury.

BANGERindicatesa hazardwhich, if not avoided, wifl

result in deathor serious injury.

WARNINGindicates a hazardwhich, if not avoided,

couid result in death or serious injury.

,a_CAUTIONindicates ahazardwhich, if not avoided, couid

result in minor or moderate injury.

NOT/CEaddresspractices not relatedto personal injury.

4 BRIGGSBndSTRATTON.COM

WARNENG Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

Some chemicals or detergents could be harmful if inhaled

or ingested, resulting in death, serious injury, nausea,

fainting or poisoning.

o Operatethis product ONLYoutdoors.

Keepexhaustgas from entering a confined areathrough

windows, doors,ventilation intakes,or other openings.

DO NOToperatethis product insideany building, carport,

porch, mobile equipment, marineapplications, or enclosure,

evenif windows and doors areopen.

Use a respirator or maskwheneverthere is a chancethat

vapors may beinhaled when using chemicals.

Readall instructions with mask so you arecertain the mask will

provide the necessary protection against inhaling harmful

vapors when using chemicals.

A WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death,

serious injury and/or property damage.

Contact with muffler area could cause burns resulting in

serious injury.

DO NOTtouch hot parts and AVOID hot exhaust gases.

Allow equipment to cool beforetouching.

Keepat least1.5 m (5 ft) of clearanceon all sides of pressure

washer including overhead.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrester designedfor the exhaust system

installed on this engine.

Replacement parts must bethe sameand installed in the same

position as the original parts.

A WARNENG Riskof electrocution. 1

Contactwith power source could causeelectric 1

shock or burn resulting in death or seriou s injury. 1NEVERspraynearpowersource.

A WARNING Use of pressure washer could create puddles

and slippery surfaces causing you to fall

resulting in death or serious injury.

Kickback from spray gun could cause

you to fall resulting in death or serious injury.

Operatepressurewasher from a stable surface.

Thecleaning areashould have adequateslopes anddrainageto

reducethe possibility of a fall due to slippery surfaces.

Beextremely careful if you must usethe pressurewasher from

a ladder,scaffolding, or any other similar location.

Firmly grasp spray gunwith both hands when using high

pressure sprayto avoidinjury when spraygun kicks back.

,a, WARNING Fueland its vapors are extremely flammable

and explosive which could cause burns,

fire or explosion resulting in death,

serious injury and/or property damage.

WHENADDING OR BRAiNiNG FUEL

. Turn pressurewasher engineOFFand let it cool at least 2

minutes before removingfuel cap. Loosen cap slowly to relieve

pressure in tank.

o Fill or drain fuel tank outdoors.

. DONOToverfill tank. Allow spacefor fuel expansion.

, if fuel spills, wait until it evaporatesbeforestarting engine.

Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

Checkfuel lines,tank, cap andfittings frequently for cracks or

leaks. Replaceif necessary.

DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

* Ensurespark plug, muffler,fuel cap,and air cleanerarein place.

* DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

* DO NOToperatethis product inside any building, carport,

porch, mobile equipment, marineapplications, or enclosure.

o DONOTtip engine or equipment at anglewhich causes fuel to

spill

DONOTsprayfiammabb liquids.

WHENTRANSPORTING,MOVINGOR REPAiRiNG EQUIPMENT

Transport/move/repair with fuel tank EMPTYor with fuel shutoff

valveOFF.

DONOTtip engine or equipment at anglewhich causes fuel to

spill.

Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELiN TANK

Store awayfrom furnaces, stoves,water heaters,clothes

dryers, or other appliancesthat havepilot light or other ignition

source becausethey could ignite fuel vapors.

_, WARNING Starter cord kickback (rapid retraction) will

pull hand and arm toward engine faster than you

can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

NEVERpull starter cord without first relieving spraygun

pressure.

When starting engine, pull cord slowly until resistance isfelt

andthen pull rapidlyto avoid kickback.

After eachstarting attempt, where enginefails to run, always

point spray gun in safedirection, pressred button and squeeze

spray gun trigger to releasehigh pressure.

Firmly grasp spray gun with both handswhen using high

pressure sprayto avoid injury when spraygun kicks back.

,a, WARNING ChemicalBurn Hazard.

Chemicals could cause burns resulting in death,

serious injury, and/or property damage.

DO NOTuse caustic liquid with pressure washer.

Use ONLYpressurewasher safe detergents/soaps. Followall

manufacturers instructions.

WARNING The high pressure stream of water that

_, his equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

. if cut byfluid, call physician immediately. DONOTtreat as a

simple cut.

* DONOTallow CHILDRENto operate pressure washer.

* NEVERrepairhigh pressure hose.Replaceit.

* NEVERrepairleaking connections with sealantof any kind.

Replaceo-ring or seal.

* NEVERconnect high pressure hoseto nozzleextension.

* Keephigh pressure hose connectedto pump and spraygun

while system is pressurized.

* ALWAYS point spray gun in safedirection, pressred button

andsqueezespray guntrigger to releasehigh pressure,every

time you stop engine.

* NEVERaim spray gun at people,animals, or plants.

* DO NOTsecure spraygun inopen position.

* DO NOTleavespray gun unattendedwhile machine is running.

* NEVERuseaspray gun which does not have a trigger lock or

trigger guard in placeand in working order.

* Always be certain spray gun, nozzlesand accessoriesare

correctly attached.

A WARNING Unintentionalsparking could causefire or

electric shock resulting n death or

serious injury.

WRENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE

WASHER

* Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug_

WHENTESTINGFORENGINESPARK

* Useapproved spark plug tester.

, DONOTcheckfor sparkwith spark plug removed.

A WARNING Starter and other rotating parts could

entangle hands, hair, clothing, or accessories

resulting in serious injury.

, NEVERoperate pressure washerwithout protective housing or

covers.

° DO NOTwear looseclothing, jewelry or anything that could be

caught in the starter or other rotating parts.

° Tie up long hair and removejewdry.

A WARNING Riskof eyeor bodily injury.

Spraycould splashback or propel

objects resulting in serious injury.

,, Always wear indirect vented (chemicalsplash) safety goggles

markedto comply with ANSi Z87.1 when using or in vicinity of

this equipment.

* NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

* Alwayswear protectiveclothing such asa long-sleeved shirt,

long pantsand close-toed shoes.

* NEVERoperate pressure washerwhen barefoot or wearing

sandalsor shorts.

A CAUTION Excessively high operating speeds could

result in minor injury and/or pressure washer damage.

Excessively low speeds impose a heavy load.

. DO NOTtamper with governor spring, links or other partsto

increase enginespeed. Pressurewasher suppliescorrect rated

pressure and flow when running at governed speed.

* DO NOTmodify pressure washer in any way.

NOTICE High pressure spray could damagefragile items

including glass.....

DONOTpointspraygunatglasswhenusingred(0°) spraytip.

, NEVERaimspraygunatplants.

NOTICE mproper treatment of pressure washer could

damage it and shorten its life.

,, if you havequestions about intended use,ask dealeror contact

qualified servicecenter.

* NEVERoperate units with brokenor missing parts, or without

protective housing or covers.

* DO NOTby-pass any safety device on this machine.

* DONOTtamper with governed spee&

* DONOToperate pressurewasher above rated pressure.

DONOTmodify pressurewasher in any way.

Beforestarting pressure washer in cold weather,check all parts of

the equipment to be sure ice has not formed there.

NEVERmove machine by pulling on hoses.Use handleprovided

on uniL

This equipment is designedto be usedwith Briggs & Stratton

Power Products authorizedparts ONLY.if equipment is used with

parts that DONOTcomply with minimum specifications,user

assumesall risks and liabilities.

6 BRIGGSandSTRATTON.COM

Yourpressurewasherrequiressomeassemblyandisready

foruseafterithasbeenproperlyservicedwiththe

recommendedoilandfuel.

if you haveanyproblems with the assemblyof your pressure

washer, contact your local Briggs &Stratton servicecenter.

if you needassistance, pleasehavethe model, revision, and

serial number from the identification label available.

Unpack Pressure Washer

1. Removethe parts bag,accessories, and inserts

included with pressure washer.

2. Opencarton completely by cutting eachcorner from

top to bottom.

3. Ensureyou haveaft included items prior to assembly.

Hems in the cartoninclude:

o Main Unit

o Handle

o High Pressure Hose

o Spray Gun

o NozzleExtensionwith Quick ConnectFitting

o Plastic AccessoryTray

o Oil Bottle

o Parts Bag(which includesthe following/:

o Operator's Manual

o GardenHose Adapters (3)

o Bag containing 5 Multi-Colored Spray Tips

o HandleFasteningHardwareKit(which includes_:

o CarriageBolts (2)

o Plastic Knobs (2)

o TreeClips (4)

Ta prepareyourpressurewasherfar aperatien, youwiii

need to perform these tasks:

1. Attach handle and accessorytray to main unit.

2. Add oil to engine crankcase.

3. Add fuel to fuel tank.

4. Connecthigh pressure hoseto spray gun and pump.

5. Connectwater supply to pump.

6. Attach nozzleextensionto spraygun.

7. Select/attachquick connect spray tip to nozzle

extension.

Attach Nandle and Accessery Tray

1. Placehandle (A) onto handle supports (B) connectedto

main unit. Makesure holes (C) in handle afignwith

holes (C) on handlesupports.

NOTICE it may be necessaryto movethe handle supports

from sideto side in order to alignthe handleso it will slide

over the handle supports.

2. insert carriage bolts (B) through holesfrom back of

unit and attacha plastic knob (F)from front of unit.

Tighten by hand.

Placeaccessorytray (F) over holes (G) on handle

(viewing from front of unit). Pushthe tree clips (N) into

the holes until they sit fiat against the accessorytray.

insert multi-colored spray tips and other supplied

accessoriesin spacesprovided in accessorytray. See

How to UseAccessory Tra}:

Add Engine Oil

1. Placepressure washer on a fiat, levelsurface.

2, Cleanarea around oil fill and removeyellow oil fill cap.

3, Using oil funnel (optional), slowly pour contents of

supplied oil into oil fill opening, frequently checkingoil

level, DONOTOVERFILL.

NOTICE improper treatment of pressure washer could

damage it and shorten its life.

, DO NOTattempt to crank or start the engine beforeit has been

properly servicedwith the recommended oil.This could result in

an enginefailure.

4, Replaceoil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

, Clean,fresh, unleadedgasoline.

, A minimum of 87 octane/87AKI (91 RON).Forhigh

altitude use, seeNigh Aititude.

, Gasolinewith up to 10% ethanol (gas@@ or up to

15% MTBE(methyl tertiary butyl ether) is acceptable.

NOTICE Avoid pressure washer damage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty,

DONOTuseunapprovedgasolinesuchasE85,

DONOTmixoilin gasoline,

DONOTmodifyengineto runonalternatefuels,

To protect the fuel system from gum formation, mix in a fuel

stabilizerwhen addingfuel. SeeStorage.AI fuel is not the

same. if you experiencestarting or performanceproblems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline.The

emission control system for this engine is EM IEngine

Modifications).

WARNING Fuelandits vapors areextremelyflammable

andexplosivewhich could causeburns,

fire or explosionresultingin death,

seriousinjury and/orproperty damage.

WHENADDINGFUEL

* Turn pressurewasher engineOFFand let it cool at least 2

minutes before removingfuel cap. Loosen cap slowly to relieve

pressure in tank.

Fill fuel tank outdoors.

* DONOToverfill tank. Allow spacefor fuel expansion.

if fuel spills, wait until it evaporatesbefore starting engine.

Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

Checkfuel fines,tank, cap and fittings frequently for cracks or

leaks. Replaceif necessary.

DONOTlight a cigaretteor smoke.

1, Cleanarea around fuel fill cap, remove cap,

2. Slowly add regular unleadedfuel (A)to fuel tank (B). Be

careful notto overfill, Allow about 4 cm (1,5 in,) (C) of

tank space for fuel expansion.

3. Install fuel capand let anyspilled fuel evaporatebefore

starting engine.

High Altitude

At altitudes over 1524 m (5,000 ft), a minimum 85 octane

85 AKI (89 RON)gasoline is acceptable.To remain

emussionscompliant, high altitude adjustment is required.

Operationwithout this adjustment will cause decreased

performance, increasedfuel consumption, and increased

emussions.See anAuthorized Briggs & Stratton dealerfor

high altitude adjustment information. Operationof the engine

at altitudes below 762 m (2,500 ft) with the high altitude kit

is not recommended.

8 BRIGGSandSTRATTON.CONI

Lubricate OoRings

Lubrication of o-rings is extremely important for installation

and operation. The useof alubricant (petroleum or synthetic

grease)during assembly helpsseat o-rings properly and

provides an improved seal. it also helps protect the o-ring

from damageby abrasion, pinching or cutting and extends

the life of the o-ring.

NOTICE ALWAYSapplya small amount of lubricant on

o-rings prior to assemblingthe garden hoseto the pump (A),

high pressure hose(B), spray gun (C),and nozzle

extension(D).

Lubricateaii connections shownbelow, following these

instructions:

1. inspect andcleanconnecting surfaces prior to

lubrication and assembly.

2. Use lubricants sparingly during assembly; a light film is

all that is required.

3. Use a small brush or cotton swab to apply grease

directly to ooringswherethey arenot accessible(QC

fitting, M22 fitting).

Connect Hose and Water Supply to Pump

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

, Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

NOTICE Removeand discard the shipping capsfrom the

pump's high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hoseand attachone end of hose

to baseof spray gun. Tighten by hand.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

* NEVERconnect high pressure hoseto nozzleextension.

* Keephigh pressure hose connectedto pump and spraygun

while system is pressurized.

* Always be certain spray gun, nozzlesand accessoriesare

correctly attached.

2. Attach other endof high pressure hoseto high

pressure outlet on pump. Tighten by hand.

Beforeconnecting garden hoseto water inlet, inspect

inlet screen (A). Cleanscreen if it contains debris or

haveit replacedif damaged.DONOTrun pressure

washer if inlet screenis damaged.

4. Run water through your garden hosefor 30 secondsto

cleanout anydebris.

HOTICE DONOTsiphon standing water for the water

supply. UseONLYcold water (less than 38°C (100°F)).

NOTICE Using a OneWayValve (vacuum breakeror check

valve) at pump inlet could cause pump or inlet connector

damage.

ThereMUSTbeatleast3 m(10ft) ofunrestrictedgardenhose

betweenthepressurewasherinletandanydevice,suchasa

vacuumbreakeror checkvalve.

* Damageto equipment resulting from failure to follow this

instruction will void warranty.

5. Connectthe garden hose (not to exceed15.24 m

(50 ft) in length) to the water inlet. Tightenby hand.

A WARNING Riskof eyeinjury.

Spray could splash back or propel objects

resulting in serious injury.

* Alwayswear indirect vented (chemical splash) safety goggles

markedto comply with ANSi Z8X1 when using or in vicinity of

this equipment.

* NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

6. Turn ONthe water, press red button (B) onthe gun and

squeezethetrigger to purgethe pump system of airand

impurities.

Checklist Before Starting Engine

Reviewthe unit's assembly to ensureyou haveperformed all

of the followi%

1. Be sureto read OperatorSafetyand Operafionsections

before using pressure washer.

2. Make sure handle is in placeand secure.

3. Checkthat oil hasbeen addedto proper level in the

engine crankcase.

4. Add proper fuel to fuel tank.

5. Checkfor properly tightened hoseconnections.

6. Checkto makesurethere areno kinks, cuts, or damage

to high pressure hose.

7. Provide a proper water supply at an adequateflow.

10 BRIGGSandSTRATTON.C01Vl

Featuresand Controts

Readthis Operator's Manual and safety rules before operating yourpressurewasher.

Comparethe illustrations with your pressure washer,to familiarizeyourself with the locations of various controls and

adjustments. Savethis manual for future reference.

A ° Spray Gun-- Controlsthe applicationof water onto

cleaningsurfacewith trigger device.Includestrigger lock.

B ° Spray Tips Soap,0°, 15°, 25° and 40°: for various

high pressure cleaningapplications.

C° Accessory Tray Provides convenientstorage for

standard and optional accessories, such as brushes

turbo wands, etc.

D ° High Pressure Nose Connectone endto water pump

and the other end to spraygun.

E ° NozzleExtension with QaiekConnect-- Allows you to

switch betweenfive different spray tips.

F - Choke Lever Preparesa cold enginefor starting.

G - Air Filter Protects engine by filtering dust and debris

out of intake air.

H - Recoil Starter Usedfor starting the enginemanually.

S- Detergent Siphoning Tube/Filter- Useto siphon

pressure washer safedetergents into the low pressure

stream.

K - FuelValve-- Usedto turn fuel supply on and off to

engine,

L =Throttle Lever Setsengine in starting mode for recoil

starter and stops a running engine.

IVl- Water Inlet Connectionfor garden hose.

N ° Automatic Cool Down System Cycleswater through

pump when water reaches51°0-68°0 (125°o155°F).

Warm water will discharge from pump onto ground. This

system prevents internal pump damage.

P =0il Brai_ Drainengine oil here.

R ° High Pressure Outlet Connectionfor high pressure

hose.

S ° Pump Developshigh pressure.

T ° Fuel Tank Fill tank with regular unleadedfuel. Always

leaveroom for fuel expansion.

items Not Shown:

identification Label(under base plate} -- Provides model

and serial number of pressure washer. Pleasehavethese

readilyavailableif calling for assistance.

0il Fill -- Checkand add engine oil here.

Warning/Operating EnstructionsTag- identifies hazards

and proper procedureto staWstop pressure washer.

ifyouhaveanyproblemsoperatingyourpressurewasher,

pleasecontactthelocalBriggs&Strattonservicecenter.

Pressure Washer Location

Clearances and Air Movement

WARNINt] Exhaustheat/gasescould ignite

combustibles, structuresor damagefueltank

causing afire, resultingin death,serious injury

and/or property'damage.

o Keepat least1.5m (5ft) clearanceonail sidesof pressure

washerincludingoverhead.

Placepressure washer outdoors in an areathat will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulateand enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is keptawayfrom anywindows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in aconfined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

A WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

Operatethis product ONLYoutdoors.

Keepexhaustgas from entering a confined areathrough

windows, doors,ventilation intakes,or other openings.

DO NOToperatethis product insideany building, carport,

porch, mobile equipment, marineapplications, or enclosure,

evenif windows and doors areopen.

Haw to Start Your Pressure Washer

To start your pressure washer for the first time, foflow these

instructions step-by-step. This starting information also

@pries if you haveletthe pressure washer sit idle for at bast

a day.

1. Placepressure washer near an outside watersource

capableof supplying water at a flow rategreaterthan

14.4 I (3.8 gallons) per minute and no lessthan

1.38 BAR(20 PSi) at pressure washer endof garden

hose. DONOTsiphon supplywater.

2. Checkthat high pressure hoseis tightly connectedto

spray gun and pump. SeeAssembly section.

3. Make sure unit is in a level position.

4. Connectgarden hoseto water inlet on pressurewasher

pump.

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

Damageto equipmentresultingfromfailuretofollowthis

instructionwillvoidwarranty,

Turn ONwater, point gun in asafedirection, pressred

button andsqueezetrigger to purgepump system of air

and impurities.

6. Attach nozzleextensionto spray gun. Tighten by hand.

Choosespray tip you want to use,puff back on collar of

nozzleextension, insert spraytip and releasecollar. Tug

on spray tip to makesure it is securely in place. See

How to Use@ray Tips.

Rotatefuel shut-off valve to "On" position (B) (fully

counter-clockwise).

12 BRIGGSandSTRATTON.CONI

Move throttle control lever (A) to "Fast" position,

shown on engineas a rabbit @.

10. Move choke lever(B) to "Cheke" IX1 position.

NOTICE Fora warm engine, besure the choke lever is in

the "Run" I{J position.

NOTICE Beforestarting the pressurewasher, be sure you

are wearing safety goggles asdescribed below.

WARNING Riskof eyeinjury.

Spraycould splashback or propel objects

resulting in serious injury.

* Always wear indirect vented (chemicalsplash) safety goggles

markedto comply with ANSi Z87.1 when using O(in vMnity of

this equipment.

* NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

11.

When starting engine, position yourself as

recommended below and grasp starter grip handle and

pull slowly until you feel some resistance.Thenpuff

rapidly to start engine.

A WARNING Starter cord kickback (rapid retraction)

will pull hand and arm toward engine faster than

_ you can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

, NEVERpull starter cord without first relieving spraygun

pressure.

* When starting engine, pull cord slowly until resistanceisfelt

andthen pull rapidlyto avoid kickback.

* After each starting attempt, where enginefails to run, always

point spray gun in safedirection, pressred button and squeeze

spray gun trigger to releasehigh pressure.

* Firmly grasp spray gun with both handswhen using high

pressure sprayto avoid injury when spraygun kicks back.

12. Return starter grip handle slowly. DONOTlet rope

"snap back"against starter.

13. Whenenginestarts,slowlymovechokeleverto "Run" J_tI

position,asenginewarms, if enginefalters,movechoke

leverto "Cheke" IXI position,thento "Run" IJtl position.

14. After eachstarting attempt, where engine fails to run,

always point gun in safe direction, press red button and

squeezespray gun trigger to releasehigh pressure.

Move choke leverto "Run" I _tt position, and repeat

steps 11 through 13.

15. if enginefails to start after six pulls, movechoke lever

to Nun I position, and repeatsteps 11through 13.

NOTICE Alwayskeepthe throttle leverin the "Fast" @

sosition when operating the pressure washer.

A WARNING The high pressure stream of waterthat

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

, DONOTallowCHILDRENto operatepressurewasher.

* Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

* NEVERaimspraygunatpeople,animals,or plants.

* DONOTsecurespraygunin openposition.

* DONOTleavespraygununattendedwhilemachineis running.

* NEVERuseaspraygunwhichdoesnothaveatriggerlockor

triggerguardinplaceandin workingorder.

* Alwaysbecertainspraygun,spraytipsandaccessoriesare

correctlyattached.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death,

serious injury and/or property damage.

Contact with muffler area could cause burns resulting in

serious injury.

, DO NOTtouch hot parts andAVOID hot exhaust gases.

Allow equipment to cool beforetouching.

Keepat least1.5 m (5 ft) of clearanceon all sides of pressure

washer including overhead.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrestor designedfor the exhaust system

installed on this engine.

Replacement parts must bethe sameand installed in the same

position as the original parts.

Now to Stop Your Pressure Washer

1. Releasespray guntrigger and let engine idle for two

minutes.

2. Move throttle control lever onengine to "Slow"

position then to "Stop" _ position.

3. Move fuel valve to "Off" position.

4. ALWAYSpoint gun in a safe direction, pressred button

and squeezespray gun trigger to releaseretainedhigh

water pressure.

A WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Newte UseAccessoryTray

Theunit is equippedwith an accessorytray with placesto

store your spray gun, nozzb extension and spray tips. There

is abe a hook atthe front of the accessorytray to hold your

high pressure hose.

NOTICE Theextrahob in thetray is for storinga utility brush.

Theextraclip in thetray isfor storinga turbo nozzle.The

brush andturbo nozzleare NOTincludedwith your pressure

washer.You canbuythese itemsasoptionalaccessories.

1. Placenozzleextensionthrough hob on accessorytray,

as shown.

2. Placespray gun through hob on accessorytray on

right side of unit.

3. insert multi-colored spray tips in spacesprovided in

accessorytray.

4. Hang high pressure hoseon hook attachedto

accessorytray onfront of tray, as shown.

14 BRIGGSendSTRATTON.CONI

Hewto Use SprayTips

The quick-connect on the nozzleextension allows you to

switch betweenfivedifferent quick connect spray tips. Spray

tips can be changedwhile pressurewasher is running once

spray gun trigger lock is engaged.Thespray tips vary the

spray pattern asshown.

Fallow these instructionsto change spray tips:

1. Pull backcollar on quick-connect and pull current

spray tip offi Store spray tips in holder provided on the

accessorytray.

WARNING The high pressurestream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

o NEVERexchangespraytipswithoutthetriggerlockbeing

engagedonthespraygun.

o DONOTtwist spraytips whilespraying.

2. Select desiredspray tip:

o Forstubborn or hardto reachsurfacesuch as

secondstory surfaces,paint removal,oil stains, rust

removal or other stubborn substances(tar. gum.

grease,wax, etc.), selectred maximum 0° spraytip.

o Formost all purposecleaningsuch ashomesiding,

brick patios,wood decks,drivewaysand sidewalks.

garagefloors, etc., selectyellow general15° or green

general25° spraytip.

o For gentlecleaning of cars/trucks, boats, RV's.

patio furniture, lawn equipment, etc., selectwhite

gentle40° spray tip.

o For applying project specific detergentsto help

breakdown stubborn dirt andgrime ona variety of

surfaces, selectblack soap spray tip.

3. Pull backoncollar, insertnewspraytip and releasecollar.

Tugon spraytip to makesureit is securely n place.

Usage Tips

o For most effective cleaning, keepspray tip from 20 to

61 cm (8 to 24 in) away from cleaningsurface.

o if you get spraytip too close, especiallyusing a high

pressure spray tip, you may damagesurface being

cleaned.

o DONOTgetcloserthan 15 cm (6 in) whencleaningtires.

Cleaning and Applying Detergent

A WARNING ChemicalBurn Hazard.

Chemicals could cause burns resulting in death,

serious injury, and/or property damage.

o DO NOTuse caustic liquid with pressure washer.

Use ONLYpressurewasher safe detergents/soaps. Followall

manufacturers instructions.

Ta apply detergent, fallow these steps:

1. Reviewuse of spray tips.

2. Preparedetergent solution as required by job.

3. Placesmall filter end of detergent siphoning tube into

detergent container.

NOTICE Make surethe filter is fully submerged in detergent

whil_ applying detergent.

NOTICE Contactwith the hot muffler could damage

detergent siphoning tube.

Wheninsertingsiphonintoa detergentsolutionbottle,routethe

tubesoasto keepitfrom inadvertentlycontactingthehotmuffler.

4. Make sure black soap spray tip is installed.

NOTICE Detergentcannot beappliedwith the high pressure

spray tips _white,green,yellow or red).

LOwPressure

Useto apply

detergent

Black White Green Yellow Red

40° 25° 15° 0°

Nigh

Pressure

5, Make sure garden hose is connectedto water inlet.

Checkthat high pressurehoseis connectedto spray

gun and pump. Turn on water.

HOTICE You must attach allhoses beforeyou start the

engine.

, Startingtheenginewithoutallthehosesconnectedandwithout

thewaterturnedONcoulddamagethepump.

Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

6. Start enginefollowing instructions How to Start Your

Pressure Washer.

7. Apply detergentto a dry surface, starting at lower

portion of areato bewashed andwork upward, using

long, even, overlapping strokes.

8. Allow detergent to "soakin"for 3-5 minutes before

washing and rinsing. Reapplyasneededto prevent

surfacefrom drying. DONOTallow detergentto dry on

(prevents streaking).

HOTICE You must flush the detergent siphoning system

after each use by placingthe filter into a bucket of clean

water,then runthe pressurewasher in low pressure for 1o2

minutes.

Pressure Washer Rinsing

For Rinsing:

1. Removeblack soap spray tip from nozzleextension.

2. Select and install desired high pressure spray tip

following instructions How to UseSpray Tips.

3. Keepspray gun a safe distance from areayou planto

spray.

WARNING Kickbackfrom spray gun could causeyou

to fall resulting in deathor serious injury.

Operatepressurewasherfroma stablesurface.

Beextremelycarefulif youmustusethepressurewasherfrom

a ladder,scaffolding,oranyothersimilarlocation.

o Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

4. Applya high pressuresprayto asmall areaandthen

checksurfacefor damage,if nodamageisfound, you

canassumeit isokayto continuerinsing.

5. Start attop of areato be rinsed,workingdown with same

overlappingstrokesasyou usedfor cleaning.

Cleaning Detergent $iphening Tube

if you usedthe detergent siphoning tube, you must flush it

with cleanwater before stopping the engine.

1. Placedetergent siphoning tube/filter in abucket full of

cleanwater.

2. Removehigh pressure spray tip from nozzleextension.

3. Select and install black soap spray tip following

instructions How to UseSpray Tips.

4. Flush for 1-2 minutes.

5. Shut off enginefollowing instructions How to Stop

Pressure Washerand turn off watersupply.

6. ALWAYSpoint gun in asafe direction, press red button

and squeezespray gun trigger to releaseretainedhigh

water pressure.

,a, WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

o ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Autematic Cool Dewn System (Thermal Relief}

if you run the engineon your pressurewasher for

3-5 minutes without pressingthe trigger on the spraygun,

circulating water in the pump can reachtemperatures above

52°C(125°F). The system engagesto cool the pump by

discharging the warm water ente the ground.

16 BRIGGSandSTRATTON,CONI

Maintenance

Maintenance Schedule

Follow the hourly or calendarintervals, whichever occurs

first. More frequent serviceis requiredwhen operating in

adverseconditions noted below.

o Changeengine oil

o Check/clean water inlet screen1

o Checkhigh pressure hose

o Checkdetergentsiphoning hose/filter

o Checkspray gun andassembly for leaks

o Cleandebris

o Checkengineoil level

o Service engineair cleaned

o Service spark plug

o Cleancooling system_

Clean if clogged, Replace if perforated or torn,

Service more often under dirty or dusty conditions.

General Recemmendations

Regular maintenancewill improve the performance and

extendthe life of the pressure washer.Seeany qualified

dealerfor service.

The pressurewasher's warranty does not cover items that

havebeen subjectedto operator abuseor negligence.To

receivefull valuefrom the warranty, the operator must

maintain the pressurewasher as instructed inthis manual,

including proper storage as detailedin Winter Storageand

Long TermStorage.

NOTICE Should you havequestions about replacing

components on your pressure washer, pleasevisit our

website at BRIGGSandSTRATTON.CONI.

Someadjustments will needto be made periodically to

properly maintain your pressure washer.

All serviceand adjustments should bemade at bast once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTICE Onceayear you should cleanor replacethe spark

plug, clean or replacethe airfilter, and checkthe spray gun

and nozzleextension assembly for wear. Anew spark plug

and cleanair filter assure proper fuebair mixture and help

your engine run better and last longer.

Pump Oil

DONOTattempt any oil maintenanceon this pump. The

pump is prequbricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

Before EachUse

1. Checkengineoil level.

2. Cleandebris.

3. Check

4. Check

5. Check

6. Check

leaks.

7. Rinse

water inlet screen for damage.

high pressure hosefor leaks.

detergentsiphoning tube andfilter for damage.

spray gun and nozzleextension assemblyfor

out garden hoseto flush out debris.

PressureWasherNJaintenance

Clean Debris

Daily or before use,cleanaccumulated debris from pressure

washer. Keeplinkage, spring andcontrols clean.Keeparea

around and behind muffler free from any combustible debris.

inspect cooling air slots and openings on the pressure

washer.These openings must bekept cleanand

unobstructed.

Pressure washer pads should bekept cleanto reducethe

risk of overheatingand ignition of accumulated debris.

o Use a damp cloth to wipe exterior surfaces clean.

NOTICE mproper treatment of pressure washer could

damageit andshorten its life.

o DONOTinsertanyobjectsthroughcoolingslots.

o Use a soft bristle brush to loosen cakedon dirt, oil, etc.

o Use a vacuum cleanerto pick uploose dirt anddebris.

Cheekand Clean Inlet Screen

Examinethe screen on the pump's water inlet. Cleanit ifthe

screen is clogged or replaceit if screen is damaged.

CheekNigh Pressore Hose

The high pressure hosecan developleaksfrom wear,

kinking, or abuse, inspectthe hoseeachtime beforeusing it.

Checkfor cuts, leaks,abrasions or bulging of cover, damage

or movement of couplings, if anyof these conditions exist,

replacethe hose immediately.

WARNING The high pressurestream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

, NEVERrepairhighpressurehose.Repbceit.

o ReplacementhoseratingMUSTequalor exceedmaximum

pressureratingofunit.

CheekDetergent Siphoning Tube

Examinethe filter on the detergent tube and clean if clogged.

Thetube should fit tightly on the barbed fitting. Examinethe

tube for leaks or tears. Replacethe filter or tube if either is

damaged.

Detergent Siphoning CheekBail

Occasionallycheck ball indetergent siphoning system may

become stuck from storage, dried soap, or minerals in water.

Thecheck ball can be freed by performing the following:

HOTtCE Beforeperforming this procedure, be sure you are

wearing safety goggles asdescribed below.

A WARNING Riskof eyeinjury.

Spraycould splashback or propel objects

resulting in serious injury.

Always wear indirect vented (chemicalsplash) safety goggles

markedto comply with ANSi Z87.1 when using or in vicinity of

this equipment.

NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

Shut off engine and turn off water supply.

ALWAYSpoint spray gunin asafe direction, pressred

button and squeezespraygun trigger to release

retainedhigh water pressure.

A WARNING The high pressurestream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Removedetergent siphoning hosefrom barbedfitting

on pump.

Usinga firm, blunt object2 mm (7/64 in) in diameteror

smaller,byatbast £5 cm (1 in) long,such asanAllen

wrench,slowlyinsertthe objectintothe barbedfitting until

you meetresistance.Thisresistanceisthecheckball.

5. Slowly push down until you feel the ball moveslightly,

push no more than 3 mm (1/8 in). Slight pressuremay

be requiredto freethe ball.

6. Repeatsteps 4 and 5 if necessary.

7. Reinstall detergent siphoning hose onto barbfitting.

8. Treat with PumpSaveras described in Protecting the

Pump during storage to prevent reoccurrence.

CheekSpray Gun

Examinethe hose connectionto the spray gun and make

sure it is secure.Testthe trigger by pressing the red button

and making surethe trigger "springs back" into placewhen

you releaseit. Youshould not beable to pressthe trigger

without pressingthe red button. Replacespray gun

immediately if it fails anyof these tests.

Nozzle Maintenance

A pulsing sensationfelt while squeezingthe spray gun

trigger may becaused by excessivepump pressure_The

principal causeof excessivepump pressure is a spray tip

clogged or restricted with foreign materials,such asdirt, etc_

To correct the problem, immediately cleanthe spray tip

following these instructions:

1. Shut off engineand turn off water supply_

2_ ALWAYSpoint spray gun in a safe direction, press red

button and squeezespraygun trigger to release

retained high water pressure_

A WARNmNGThe high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

ALWAYSpointsprayguninsafedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

3. Removespray tip from end of nozzleextension.

4. Use a small paperclip to free anyforeign material

clogging or restricting spray tip (A).

5. Removenozzleextensionfrom spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through nozzleextension. Backflush

between 30 to 60 seconds.

18 BRIGGSandSTRATTON.CONI

10.

11.

Reinstall spray tip into nozzleextension.

Reconnect nozzleextensionto spray gun.

Make sure garden hose is connectedto water inlet.

Checkthat high pressurehoseis connectedto spray

gun and pump. Turn on water.

Start enginefollowing instructions How to Start Your

Pressure Washer.

Test pressurewasher by operating with each quick

connect spray tip.

O°RingMaintenance

Through the normal operationof your pressurewasher,

o-rings are usedto keepthe connections of the hosesand

spray gun tight and leak-free. These o-rings may become

worn or damaged.

An O-Ring MaintenanceKit is provided with your pressure

washer which includes replacementoorings, rubber washer

and water inlet filter. Referto the instruction sheet provided

in the kit to serviceyour unit's o-rings. Notethat you will not

use all of the parts in the kit.

To remove a worn or damagedo-ring, usea small flathead

screwdriver to get underneaththe o-ring and pry it off.

WARNING The high pressurestream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

NEVERrepairleakingconnectionswithsealantofanykind.

Replaceo-ringor seal.

Engine Maintenance

A WARNING Unintentionalsparking could cause fire or

electric shock resulting n death or

serious injury.

WHENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE

WASHER

Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

Use approved spark plug tester,

o DONOTcheckfor sparkwith spark plug removed,

Oil

Oil Recommendations

We recommendthe useof Briggs & Stratton Warranty

Certified oils for best performance. Otherhigh-quality

detergent oils areacceptableif classified for serviceSF, SG,

SH, SJ or higher. DONOTuse specialadditives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Usethe chart to selectthe best viscosity for the

outdoor temperature rangeexpected.

°F °C

104 --_"_ __ _ " 40

86 _ • _1- 30

68 _ i[_o_ 20

50 _ 10

32 __ l--_ 0

14 __ ._, -10

-4 ........ -20

-22 ' -30

• Below4°C(40°F)theuseofSAE30 will resultin hardstarting.

** Above 27°C (80°F) the useof 10W30 may cause increasedoil

consumption. Checkoil level more frequently.

NOTICE Synthetic oil meeting ILSACGF-2,API

certification mark and API servicesymbol with

"SJ/CF ENERGYCONSERVING"or higher, is an

acceptableoil at alltemperatures. Useof synthetic

oil does not alter required oil change intervals.

Checking Oil Level

Oil levelshould be checked prior to each useor at bast

every 8 hours of operation. Keepoil levelmaintained.

1. Make sure pressure washer is on a levelsurface.

2. Cleanarea around oi fill and remove oil fill cap.

3. Verify oil is at the point of overflowing at oil fill

opening.

4. Replaceand tighten oil fill cap.

Adding Engine Oil

1. Make sure pressure washer is on a levelsurface.

2. Checkoil levelas described in Checking 0/1Level

3. if needed,slowly pour oil into oil fill opening to the

point of overflowing at oil fill.

4. Replaceand tighten oil fill cap.

Changing Engine Oil

if you are usingyour pressurewasher under extremely dirty

or dusty conditions, or in extremely hot weather, changethe

oil more often.

A CAUTION Avoid prolonged or repeatedskin contact

with usedmotor oil.

Usedmotoroil hasbeenshownto causeskincancerin certain

Thoroughlywashexposedareaswithsoapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOiL TOCOLLECTIONCENTERS.

Changeoil while engine is still warm from running, as

follows:

1. Make sure unit is on a levelsurface.

Service Air Cleaner

Your enginewill not run properly and may be damaged if

you run it with a dirty air cbaner. Service more often if

operating under dirty or dusty conditions.

Disconnectthe sparkplug wire from the spark plugand

placethe wire where it cannotcontact spark plug.

Cleanarea around oil drain plug(A). Theoil drain plug

is locatedat baseof engine,opposite carburetor.

Removeoil drain plug anddrain oil completely into a

suitable container.

Reinstall oil drain plug andtighten securely. Removeoil

fill cap.

Slowly pour oil (about 0.6 liters (20 oz.)) into oilfill

opening (B) to the point of overflowing (C) at oil fill

cap. DONOToverfill.

Reinstall oil fill cap. Fingertighten cap securely.

Wipe up any spilled oil.

Tosewiee the air cleaner, feiiew these steps:

1. Loosen screw (A) andtilt cover (B) down.

Service Spark Plug

Changingthe spark plug will helpyour engineto start easier

and run better.

1. Cleanarea around spark plug.

2. Removeand inspect spark plug.

3. Replacespark plug if electrodesare pitted, burnedor

porcelain is cracked. Usethe recommended

replacementplug. See Specifications.

4, Checkelectrode gapwith wire feeler gauge and reset

spark plug gap to recommended gap if necessary(see

Specifications).

5, Install sparkplug and tighten firmly,

inspect Muffler and Spark Attester

inspectthe muffler for cracks,corrosion, or other damage.

Remove the spark arrester, if equipped,and inspectfor

damageor carbon blockage, if replacementparts are

required, make sureto useonly original equipment

replacementparts.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death,

serious injury and/or property damage.

Contact with muffler area could cause burns resulting in

serious injury.

o DO NOTtouch hotparts andAVOIDhot exhaust gases.

Allow equipment to cool beforetouching.

Keepat least 1.5 m (5 ft) of clearanceon all sidesof pressure

washer including overhead.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain aspark attester designed for the exhaust system

installed on this engine.

Replacement parts must bethe sameand installed in the same

position as the original parts.

2. Carefully removecartridge (C) assembly.

3. To cleancartridge, gently tap pleatedpaperside on a

fiat surface.

4. Reinstall cleanor new cartridge assembly inside cover.

5. insert cover's tabs (t}) into slots in bottom of base(F).

6. Tilt cover up and tighten screw securelyto base.

20 BRIGGSandSTRATTON.CONI

Page is loading ...

Briggs & Stratton 020477-00 Owner's manual

Brand: Briggs & Stratton

Model: 020477-00

Category: High-pressure cleaners

Type: Owner's manual

Download PDF

report

in other languages

español: Briggs & Stratton 020477-00 El manual del propietario
português: Briggs & Stratton 020477-00 Manual do proprietário

Briggs & Stratton 020477-00 Owner's manual

Briggs & Stratton 020477-00 Owner's manual

in other languages

Related papers

Other documents