LG HT906TAW User guide

Category
DVD players
Type
User guide
P/NO : MFL67164701
HT906TAW (HT906TAW, SH96TA-S/ W, SH96SB-C, W95)
Please read this manual carefully before operating
your set and retain it for future reference.
OWNER’S MANUAL
DVD Wireless Home cinema
System
HT906TAW-D0_DTURLLK_ENG_4701.indd 1 2011-01-25 �� 4:48:05
1 Getting Started
Getting Started2
Getting Started
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure that
may be of sucient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturers
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owners manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specied herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specication page of this
owners manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, re or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, shall be placed on the
apparatus.
HT906TAW-D0_DTURLLK_ENG_4701.indd 2 2011-01-25 �� 4:48:06
Getting Started 3
Getting Started
1
Copyrights
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material
without permission. This product features the copy
protection function developed by Macrovision. Copy
protection signals are recorded on some discs. When
recording and playing the pictures of these discs picture
noise will appear. This product incorporates copyright
protection technology that is protected by U.S. patents
and other intellectual property rights. Use of this
copyright protection technology must be authorized
by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is
prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION OUTPUT.
IF THERE ARE QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT,
PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When setting
the option to Live File System, you cannot use it on LG
players. (Mastered/ Live File System : Disc format system
for Windows Vista)
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance
will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city oce, waste disposal
service or the shop where you purchased
the product.
5. EEE Compliance with Directive.
Europe Notice
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC, 2004/108/EC, 2006/95/EC and
2009/125/EC.
Please contact to the following address for
obtaining a copy of the DoC (Declaration of
Conformity).
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327
AE Almere. The Netherlands
(Tel : +31-(0)36-547-8888)
Indoor Use Only
RF Radiation Exposure Statement
This equipment should be installed and operated
with minimum distance 20 cm between the
radiator and your body.
Italy Notice
A general authorization is requested for outdoor
use in Italy.
The use of these equipments is regulated by:
1. D.L.gs 1.8.2003, n. 259, article 104 (activity
subject to general authorization) for outdoor
use and article 105 (free use) for indoor use, in
both cases for private use.
2. D.M. 28.5.03, for supply to public of RLAN access
to networks and telecom services.
L’uso degli apparati è regolamentato da:
1. D.L.gs 1.8.2003, n. 259, articoli 104 (attività
soggette ad autorizzazione generale) se utilizzati
al di fuori del proprio fondo e 105 (libero uso) se
utilizzati entro il proprio
fondo, in entrambi i casi per uso private.
2. D.M. 28.5.03, per la fornitura al pubblico
dell’accesso R-LAN alle reti e ai servizi di
telecomunicazioni.
Brazil Notice
Este equipamento opera em caráter secundário, isto
é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e
não pode causar interferência a sistemas operando
em caráter primário.
HT906TAW-D0_DTURLLK_ENG_4701.indd 3 2011-01-25 �� 4:48:06
Table of Contents4
Table of Contents
1 Getting Started
2 Safety Information
6 Unique Features
6 Portable In
6 USB Direct Recording
6 Full HD up-scaling
6 Home Theater Speaker ez Setup
6 Accessories
7 Introduction
7 Playable Discs
7 About the “&” Symbol Display
7 Symbols Used in this Manual
7 Regional Codes
8 Playable file Requirement
9 Remote control
10 Front panel
11 Rear panel
2 Connecting
12 Assembling the speaker
14 Attaching the speakers to the unit
15 Wireless speakers connection
17 Positioning the system
18 Connections to Your TV
18 Component Video Connection
19 HDMI Out Connection
20 Video Connection
21 Resolution Setting
21 Video Output Resolution
22 AUX In Connection
22 AUDIO (PORT. IN) In Connection
22 Listening to music from your portable
player or external device
23 USB Connection
24 OPTICAL In connection
24 Home theater speaker ez setup
24 Antenna Connection
3 System Setting
25 Adjust the setup settings
25 OSD Initial language settings -
Optional
25 To display and exit the Setup menu
26 Language
26 Display
27 Audio
28 Lock (Parental Control)
29 Others
4 Operating
30 Using the Home Menu
30 Basic Operations
31 Other Operations
31 Displaying Disc Information on-screen
32 To display the DVD Menu
32 To display the DVD title
32 1.5 times speed playback
32 Screen Saver
32 Starting play from selected time
32 Resume playback
32 Changing subtitle code page
33 Marked Playback
34 Viewing a PHOTO file
35 Sleep Timer Setting
35 Dimmer
35 Turn off the sound temporarily
35 Last Scene Memory
35 System Select - Optional
35 Adjust the speaker level settings
36 Radio Operations
36 Listening to the radio
36 Presetting the Radio Stations
36 Deleting all the saved stations
36 Deleting a saved station
36 Improving poor FM reception
36 Seeing information about a radio
station
37 Sound adjustment
37 Setting the surround mode
38 Advanced Operations
38 Recording to USB
HT906TAW-D0_DTURLLK_ENG_4701.indd 4 2011-01-25 �� 4:48:06
Table of Contents 5
1
2
3
4
5
6
5 Troubleshooting
39 Troubleshooting
6 Appendix
40 Maintenance
40 Handling the Unit
40 Notes on Discs
41 Area Code List
42 Language code List
43 Trademarks and Licenses
44 Specifications
HT906TAW-D0_DTURLLK_ENG_4701.indd 5 2011-01-25 �� 4:48:06
Getting Started6
Getting Started
1
Unique Features
Portable In
Listen to music from your portable device. (MP3,
Notebook, etc)
USB Direct Recording
Records music from CD to your USB device.
Full HD up-scaling
Views Full HD picture quality with simple setup.
Home Theater Speaker ez
Setup
Listen to sounds from TV, DVD and Digital device
with vivid 5.1 (2.1 or 2.0) ch mode.
Accessories
Please check and identify the supplied accessories.
Remote control (1) Battery (1)
FM antenna (1) Speaker cables (6)
HDMI Cable (1) Video cable (1)
HT906TAW-D0_DTURLLK_ENG_4701.indd 6 2011-01-25 �� 4:48:06
Getting Started 7
Getting Started
1
Introduction
Playable Discs
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG les. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and nalized only.
DVD-RW (8 cm / 12 cm disc)
Video mode and nalized only.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm / 12 cm disc)
Video mode and nalized only.
Audio CD: Music CDs or CD-R/CD-
RW in music CD format that can be
purchased.
About the “
&
” Symbol
Display
&
may appear on your TV display during
operation and indicates that the function explained
in this owners manual is not available on that
specic media.
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and nalized
t
Audio CDs
y
Video les contained in the
USB/Disc
u
Audio les contained in the
USB/Disc
i
Photo les
,
Note
Indicates special notes and operating features.
,
Tip
Indicates tip and hints for making the task easier.
>
Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or ALL.
y
Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
y
If you try to play a DVD with a dierent regional
code from your unit, the message “Check
Regional Code appears on the TV screen.
HT906TAW-D0_DTURLLK_ENG_4701.indd 7 2011-01-25 �� 4:48:07
Getting Started8
Getting Started
1
Playable file
Requirement
MP3/ WMA music file requirement
MP3/ WMA le compatibility with this unit is limited
as follows :
y
Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
y
Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
y
Support Version : v2, v7, v8, v9
y
Maximum les : Under 999
y
File extensions : .mp3”/ .wma
y
CD-ROM le format : ISO9660/ JOLIET
y
We recommend that you use Easy-CD Creator,
which creates an ISO9660 le system.
Photo file requirement
Photo le compatibility with this unit is limited as
follows :
y
Max pixel in width : 2 760 x 2 048 pixel
y
Maximum les : Under 999
y
Some discs may not operate due to a dierent
recording format or the condition of disc.
y
File extensions: .jpg”
y
CD-ROM le format : ISO9660/ JOLIET
DivX file requirement
DivX le compatibility with this unit is limited as
follows:
y
Available resolution: within 720 x 576 (W x H)
pixels.
y
The le name of the DivX subtitle should be
entered within 45 characters.
y
If there is impossible code to express in the
DivX le, it may be displayed as “ _ “ mark on the
display.
y
Frame rate : less than 30 fps.
y
If the video and audio structure of recorded
les is not interleaved, either video or audio is
outputted.
y
Playable DivX le : .avi”, .mpg”, .mpeg”, .divx
y
Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
y
Playable Codec format : “DIVX3.xx, “DIVX4.xx”,
“DIVX5.xx, “MP4V3”, “3IVX”.
y
Playable Audio format : AC3”, “PCM, “MP3”, “WMA,
“DTS.
y
Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
y
Bit rate : within 32 to 320 kbps (MP3), 40 to 192
kbps (WMA)
y
For Discs formatted in Live le system, you can
not it on this unit.
y
If the name of movie le is dierent from that of
the subtitle le, during playback of a DivX le,
subtitle may not be display.
y
If you play a DivX le dier from DivXspec, it may
not operate normally.
HT906TAW-D0_DTURLLK_ENG_4701.indd 8 2011-01-25 �� 4:48:07
Getting Started 9
Getting Started
1
Battery Installation
Remove the battery cover on the
rear of the Remote Control, and
insert one (size AAA) battery with
4
and
5
matched correctly.
• • • • • •
a
• • • • •
P
RADIO&INPUT: Changes
input sources.
MARKER: Marks play list.
1
POWER:
Switches the unit ON
or OFF.
B
OPEN/CLOSE:
Opens and
closes the disc drawer.
SLEEP: Sets the System to turn o
automatically at a specied time.
(Dimmer : The display window will
be darken by half.)
m
INFO/DISPLAY:
Accesses On-
Screen Display.
n
HOME:
Displays the [Home
Menu].
DISC MENU:
Accesses the menu
on a DVD disc.
• • • • • •
b
• • • • •
W/S/A/D
(up/ down/ left/
right): Used to navigate on-screen
displays.
PRESET +/-:
Selects programme
of Radio.
TUNING +/-: Tunes in the desired
radio station.
b
ENTER:
Acknowledges menu
selection.
Presetting the radio stations.
x
RETURN: Moves backwards
in the menu or exits the setup
menu.
TITLE:
If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
• • • • • •
c
• • • • •
Z
STOP:
Stops playback.
d
PLAY, MONO/STEREO:
Starts
playback. Selects Mono/ Stereo.
M
PAUSE/STEP:
Pauses playback.
C/V
SKIP:
Goes to the next
or previous chapter / track / le.
c/v
SCAN:
Searches
backward or forward.
• • • • • •
d
• • • • •
SPEAKER LEVEL: Sets the sound
level of desired speaker.
SOUND EFFECT: Selects a sound
eect mode.
VOL -/+ (Volume): Adjusts
speaker volume.
OPTICAL: Changes input source
to optical directly.
MUTE: Mutes the sound.
• • • • • •
e
• • • • •
0-9 numerical buttons: Selects
numbered options in a menu.
h
REPEAT:
Selects a play
mode. (Repeat/ Random)
CLEAR: Removes a number when
setting the password.
• • • • • •
f
• • • • •
TV Control buttons: Controls the
TV. (LG TV only)
-
You can control the sound
level, input source, and power
switching of LG TVs as well.
Hold POWER (TV) and press PR/
CH (
W/S
) button repeatedly
until the TV turns on or o.
X
REC:
USB Direct Recording.
?
:
This button is not available.
RDS : Radio Data System.
PTY : Views the various displays of
the RDS.
Remote control
HT906TAW-D0_DTURLLK_ENG_4701.indd 9 2011-01-25 �� 4:48:07
Getting Started10
Getting Started
1
Front panel
a b c
k j i h g f e d
a
1/!
(POWER)
Switches the unit ON or OFF.
b
Disc Tray
c
Display window
Shows the current status of the unit.
d
VOLUME
Adjusts speaker volume.
e
F
(FUNCTION)
Changes the input source or function.
f
C/V
(SKIP)
Go to next or previous le/track/chapter.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
g
Z
(STOP)
Stops playback.
h
z/M
(PLAY/PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
i
B
(OPEN/CLOSE)
Opens or closes the disc tray.
j
USB Port
Connects a USB device.
k
PORT. IN
Connects to a portable player with audio
outputs.
HT906TAW-D0_DTURLLK_ENG_4701.indd 10 2011-01-25 �� 4:48:07
Getting Started 11
Getting Started
1
a
Power cord
b
Speakers connectors
Connects the speaker cables.
c
Cooling Fan
d
Antenna Connector
FM- Connects the FM wired antenna.
e
VIDEO OUT
Connects to a TV with video inputs.
f
HDMI OUT
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
g
OPTICAL IN
Connects to optical audio equipment.
h
COMPONENT VIDEO (Y P
B
P
R
)OUTPUT
(PROGRESSIVE SCAN)
Connects to a TV with Y P
B
P
R
inputs.
i
AUX (L/R) INPUT
Connects to an external source with 2 channel
audio outputs.
Rear panel
a b c d e
i h g f
HT906TAW-D0_DTURLLK_ENG_4701.indd 11 2011-01-25 �� 4:48:07
2 Connecting
Connecting12
Connecting
2
Assembling the
speaker
Before connecting the speakers, assemble the
speakers. Please check the items for assembling the
speakers.
Preparation
Cable
Pole
Base
Speaker
Screw
1. Attach the pole to the base, then secure the
connection with a supplied screw.
(Small)
2. Insert a speaker wire from the bottom of the
base.
(Big)
3. Attach the speakers to the speaker stands by
rotating the screws.
(Small)
HT906TAW-D0_DTURLLK_ENG_4701.indd 12 2011-01-25 �� 4:48:08
Connecting 13
Connecting
2
4. Connect the speaker wire to the terminal on the
speaker.
Make sure the wire marked black goes in to the
terminal marked “–” (minus) and the other wire
goes in to the terminal marked
“+” (plus).
Be careful that the speaker
does not fall down.
Otherwise it may result in
the speaker malfunctioning
and causing personal injury
and/ or property damage.
>
Caution
HT906TAW-D0_DTURLLK_ENG_4701.indd 13 2011-01-25 �� 4:48:08
14
Connecting
2
Connecting
Attaching the speakers
to the unit
1. Connect the wires to the unit.
Match each wires colored band to the same
colored connection terminal on the rear of the
unit. To connect the cable to the unit, press
each plastic nger pad to open the connection
terminal. Insert the wire and release the nger
pad.
Connect the black stripe of each wire to the
terminals marked -(minus) and the other end
to the terminals marked + (plus).
2. Connect the wires to the speakers.
Connect the other end of each wire to the
correct speaker according to the color coding:
Color Speaker Position
Green Center Center
Orange
Sub woofer Any front position
Red Front Front right
White Front Front left
To connect the cable to the speakers, press each
plastic nger pad to open the connection terminals
on the base of each speaker. Insert the wire and
release the nger pad.
y
Be careful to make sure children do not put
their hands or any objects into the *speaker
duct.
*Speaker duct : A hole for plentiful bass
sound on speaker cabinet (enclosure).
y
The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
>
Caution
HT906TAW-D0_DTURLLK_ENG_4701.indd 14 2011-01-25 �� 4:48:08
Connecting 15
Connecting
2
Wireless speakers connection
LED indicator of wireless receiver
LED Color Operation
Blue
The wireless receiver is receiving
the signal of the wireless
transmitter.
Red
The Wireless Receiver is in
standby mode.
O (No
display)
The Wireless Receiver is turned
o.
Initial setting an ID of wireless
receiver
1. Connect the Wireless Receiver and the rear
speaker (right, left) with the speaker cables.
2. Connect the power cord of the Wireless
Receiver to the outlet.
3. Turn on the main unit and Wireless Receiver:
The main unit and wireless receiver will be
automatically connected.
“MATE OK” appears in display window.
Setting an ID of wireless receiver
When the unit is manufactured, the ID is already set.
If an interference occurs or you use a new wireless
receiver, an ID should be set again.
1. Turn on the main unit and turn o the wireless
receiver.
2. Press and hold
Z
(STOP) on the front of unit
and MUTE on the remote control. “REMATE”
appears in display window.
3. Turn on the Wireless Receiver. A new ID is set.
About Ferrite Core (for EMI only)
Be sure to attach the ferrite core to the speaker
cable (for connecting to this unit and wireless
receiver). This ferrite core can reduce noises.
How to attach the ferrite core
1. Press the stopper [a] of the ferrite core to open.
2. Wind the speaker cables once on the ferrite
core.
3. Close the ferrite core until it clicks.
Refer to the g.3 and comment.
1
2
3
(g. 3)
Rear of wierless receiver
The length
here is as short
as possible.
HT906TAW-D0_DTURLLK_ENG_4701.indd 15 2011-01-25 �� 4:48:08
Connecting16
Connecting
2
y
If there is a strong electromagnetic wave
product nearby, interference may occur. Put
the unit (Wireless Receiver and main unit)
away from there.
y
If there is no audio signal for longer than
10 minutes, the Wireless Receiver will
automatically switch to standby mode. In
power saving mode, both LEDs will turn red.
LEDs will turn blue when there is any audio
signal back.
y
If you operate main unit then wireless
speakers (rear speakers) sound within a few
seconds in standby mode.
y
Set the distance between this unit and
Wireless Receiver within 10 m (32 ft.).
y
Optimum performance can be
implemented only when the Wireless
Transmitter and the Wireless Receiver within
distance of 2 m (6 ft.) to 10 m (32 ft.) is used
since communication failure may occur if
longer distance is used.
y
Be sure to match the speaker cable to the
appropriate terminal on the components:
+ to + and – to –. If the cables are reversed,
the sound will be distorted and will lack
bass.
y
It takes a few seconds (and may take longer)
for the Wireless Transmitter and Wireless
Receiver to communicate with each other.
y
Use the rear speaker at least 30 cm (11 inch)
away from either TV screen or PC monitor.
,
Note
HT906TAW-D0_DTURLLK_ENG_4701.indd 16 2011-01-25 �� 4:48:08
Connecting 17
Connecting
2
Positioning the system
The following illustration shows an example of
positioning the system. Note that the illustrations
in these instructions dier from the actual unit for
explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position ( ).
A
B
D
D
E
E
F
F
A
A
A
A
A
G
G
C
C
A
B
A
Front left speaker (L)/ Front right speaker (R):
Place the front speakers to the sides of the
monitor or screen and as ush with the screen
surface as possible.
Center speaker: Place the center speaker above
or below the monitor or screen.
Surround left speaker (L)/ Surround right
speaker (R):
Place these speakers behind your listening
position, facing slightly inwards.
Subwoofer: The position of the subwoofer is
not so critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it slightly
toward the center of the room to reduce the wall
reections.
Unit
HT906TAW-D0_DTURLLK_ENG_4701.indd 17 2011-01-25 �� 4:48:09
Connecting18
Connecting
2
Connections to Your
TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
y
Depending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
y
Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
,
Note
y
Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel.
y
Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
>
Caution
Component Video Connection
Connect the COMPONENT VIDEO OUTPUT
(PROGRESSIVE SCAN) jacks on the unit to the
corresponding input jacks on the TV using
component cables.
You can hear the sound through the systems
speakers.
Unit
TV
Green
Blue
Red
HT906TAW-D0_DTURLLK_ENG_4701.indd 18 2011-01-25 �� 4:48:10
Connecting 19
Connecting
2
HDMI Out Connection
If you have a HDMI TV or monitor, you can connect
it to this unit using a HDMI cable (Type A, High
Speed HDMI™ Cable).
Connect the HDMI OUT jack on the unit to the
HDMI IN jack on a HDMI compatible TV or monitor.
Set the TVs source to HDMI (refer to TV’s Owner’s
manual).
Unit
TV
y
You can fully enjoy digital audio and video
signals together with this HDMI connection.
y
When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 21.)
,
Tip
y
If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or
may not output.
y
When you connect a HDMI or DVI
compatible device make sure of the
following:
- Try switching o the HDMI/DVI device
and this unit. Next, switch on the HDMI/
DVI device and leave it for around 30
seconds, then switch on this unit.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p),
1 280 x 720p, 1920 x 1080i or 1920 x 1080p
video input.
y
Not all HDCP-compatible HDMI or DVI
devices will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
y
If there is noise or lines on the screen, please
check the HDMI cable and use a higher
version cable than High Speed HDMI™
Cable.
,
Note
y
Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn o the unit and then turn it
on again.
y
When the HDMI connection with HDCP is
not veried, TV screen is changed to black
or green screen or the snow noise may
occur on the screen. In this case, check the
the HDMI connection, or disconnect the
HDMI cable.
>
Caution
HT906TAW-D0_DTURLLK_ENG_4701.indd 19 2011-01-25 �� 4:48:10
Connecting20
Connecting
2
Video Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
You can hear the sound through the systems
speakers.
Unit
TV
Yellow
HT906TAW-D0_DTURLLK_ENG_4701.indd 20 2011-01-25 �� 4:48:10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

LG HT906TAW User guide

Category
DVD players
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages