Quantum ROLLERSHADE HARDWARE SYSTEM Installation guide

Brand: Quantum

Model: ROLLERSHADE HARDWARE SYSTEM

Type: Installation guide

February 2014

INSTALLATION MANUAL

QUANTUM

ROLLERSHADE HARDWARE SYSTEM

PAGE 2

CORNERS

Note: For windows in reveal brackets must be top

fixed for deductions to work.

FRONT EDGE

ON FACE

BACK EDGE

BAYS

ON FACE

TOP FIX FRONT EDGE

TOP FIX BACK EDGE

ANGLED LINKED BLINDS  90° CORNERS

FACE FIT

TOP FIT FRONT EDGE of REVEAL

Corners in Reveal- Front Edge Deductions

Through Blind +50mm(from corner)

Butt Blind - 0mm

Corners in Reveal- Back Edge Deductions

Through Blind - 0mm

Butt Blind - 60mm (37mm Tube)

- 80mm (50mm Tube)

Corners on Face Deductions (Butt Blinds)

38mm Projection bracket - 75mm

55mm Projection Bracket - 90mm

Bays in Reveal Deductions

Front Edge of Reveal - 0mm - 0mm - 0mm

Back Edge of Reveal - 22mm - 44mm - 22mm

Bays on Face Deductions

38mm Projection Bracket - 28mm - 56mm - 28mm

55mm Projection Bracket - 33mm - 66mm - 33mm

Angled Link Bay on Face Deductions

38mm Projection Bracket - 38mm - 76mm -38mm

55mm Projection Bracket - 43mm - 86mm -43mm

Angled Link Bay in Reveal Deductions

Front Edge of Reveal - 10mm - 20mm - 10mm

*Gap between Brackets 30mm approximate

Angled Link Corners on Face

Measure Blinds into the corner and deduct 76mm from each

blind.

Angled Link Corners in Reveal

Measure from the front edge of reveal and deduct 10mm

from each blind.

In all corner linked situations we strongly recommend

that the brackets are fixed in exact location first and then

measured outside edge to outside edge of the bracket to

ensure the gap is minimised.

*Gap between Brackets 30mm approximate

ANGLED LINKED BLINDS  BAY WINDOW

MEASURE WALL

Brackets to be fixed to wall

CEILING FIT FRONT EDGE

OF REVEAL

FACE FIT

Deductions are only approximate due to thickness of fabric and drop, for

best results install the thru blind then measure for the butt blind.

QUANTUM MEASURING DEDUCTIONS

PAGE 3

QUANTUM INSTALLATION

1. Fix bracket with the screws

provided

2. Place the chain drive in the

bracket (1)

3. Slide it down until it

clicks (2).

4. Place the tube adapter on the

chain drive. Press the idle end

and lift the blind.

5. Snap it to the bracket. 6. Slide the end caps onto the

brackets.

1. Slide a screw driver between

idle end and bracket and

push the idle end in the chain

drive direction. Slide the end

cap towards you.

2. Move the blind downwards

out of the bracket.

3. Push the pin of the chain

drive and take the chain drive

out of the bracket.

4. Place a screw driver under the

pin of the chain drive and pull it

outwards. Remove chain drive

from the bracket.

REMOVAL - STANDARD ROLLER SYSTEM

INSTALLATION - STANDARD ROLLER SYSTEM

PAGE 4

INSTALLATION - STANDARD ROLLER SYSTEM WITH LEVELLER BRACKET

1. Make sure that the opening

for the Allen key is pointing

downwards before installing the

brackets. Change the orientation

by loosening the 2 screws and

turning the leveller 90°. Fix the

screws.

2. To adjust skewing, put the

provided Allen key into the

screw of the leveller and turn

it left or right to move the

blind up or down.

QUANTUM INSTALLATION

PAGE 5

QUANTUM INSTALLATION

INSTALLATION - LINKED BLINDS

1. Place the tube adaptor on the

chain drive head. Press the

idle end and lift the blind.

2. Fix the outer bracket with the

screws provided.

3. Slide the aligner or the

connector through the

bracket into the idle end.

4. Place the tube adaptor on the

aligner or connector head.

5. Press the spring loaded idle

with locking ring end and lift

the blind and snap it to the

bracket.

6. To align the bottom rails, push

the blind against the idle end

(1), turn the blind, level the

bottom rail with the other one

(2). Release to x the position

(3).

NOTE: This is not possible

when using the standard

connector set.

7. Fix the blind by turning the

locking ring against the idle

end.

8. Slide the end caps onto the

brackets.

NOTE: The aligner component has an extra metal bearing ring which is only required if the centre space

between two blinds is being extended. For normal installation this can be removed using an allen key.

PAGE 6

1. Slide the end cap towards

you.

2. Unfasten the locking ring.

Slide a screw driver between

locking ring and bracket

and push the idle end in the

aligner direction.

3. Move the blind downwards

out of the bracket. Pull the

aligner or connector out of

the idle end.

QUANTUM INSTALLATION

REMOVAL - LINKED BLINDS

1. Unfasten the locking ring. 2. Slide up the chain drive. 3. Push blind in the idle end

direction (2) and lower blind

to remove from bracket (3).

QUANTUM INSTALLATION

REMOVAL - SPRING BOOSTER

1. Place the idle end into the

bracket. Push blind in the idle

end direction (1) and lift blind

up (2).

2. Lift the blind up until chain

drive clicks in place (3).

QUANTUM INSTALLATION

INSTALLATION - SPRING BOOSTER

click

3. Fix the blind by turning the

locking ring against the idle

end.

PAGE 7

QUANTUM INSTALLATION

INSTALLATION - HEADBOX SYSTEM

1. Fix headbox back plate to wall

by drilling through extrusion

and slide brackets into keyway.

Tighten grubscrew.

3. Clip headbox front plate inside

keyway at the top of the

back plate.

NOTE: End cap removed for

demonstration only.

2. Slide end caps into the

headbox back plate.

4. Clip headbox front plate into

place to secure the endcaps.

1. Level the side guiding channel

ush with the headbox end

cap. Mark this position.

3. Fix the lower clip - and clips

at 1000 mm intervals - before

installing the channel.

2. Fix the top clip with a distance

max 7.5mm from the bottom

of the headbox end cap.

INSTALLATION - SIDE CHANNELS

4. Place the bottom rail into the

side guiding channel. Snap

and remove tab on chain

drive end.

5. Snap channel into clips.

Tab



PAGE 8

QUANTUM MANUAL

INSTALLATION MANUAL INFORMATION

This Installation Manual is only a guide to the measurement and installation procedures

for the Quantum Hardware System. New Zealand Window Shades Limited does not

warrant the accuracy contained in this manual.

The information contained in this Installation Manual is based on the measurement and

installation data known to us at the time of issue and is therefore subject to changes

or amendments at anytime without notice, and the right to change or amend is hereby

expressly reserved by New Zealand Window Shades Limited.

IMPORTANT

This Installation Manual at all times remains the property of New Zealand Window

Shades Limited. Its contents are strictly condential and may not be reprinted, copied,

reproduced or multiplied in any form. This Installation Manual must be maintained in

its original form and must be returned to New Zealand Window Shades Limited upon

rst request. New Zealand Window Shades Limited is not responsible to you or anyone

else for any loss suered in connection with the use of this Installation Manual or any

of the content.

® Registered Trade Marks of Hunter Douglas Limited.

NEW ZEALAND WINDOW SHADES LIMITED

PO BOX 12 785 PENROSE,

AUCKLAND 1642

NEW ZEALAND

Customer Service Phone: 0800 223 224

Quantum ROLLERSHADE HARDWARE SYSTEM Installation guide

Quantum ROLLERSHADE HARDWARE SYSTEM Installation guide

Quantum ROLLERSHADE HARDWARE SYSTEM Installation guide

Other documents