The information contained herein is deemed accurate as of 3/30/2023 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 3
Model G0937
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0937 6" X 10" COMBO LATHE/MILL
Product Dimensions:
Weight................................................................................................................................................................ 99 lbs.
Width (side-to-side) x Depth (front-to-back) x Height...............................................................24-1/2 x 21 x 22-1/2 in.
Footprint (Length x Width)............................................................................................................................22 x 10 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content...................................................................................................................................................... Lathe
Weight...................................................................................................................................................... 60 lbs.
Length x Width x Height............................................................................................................. 27 x 14 x 12 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content..........................................................................................................................................................Mill
Weight...................................................................................................................................................... 35 lbs.
Length x Width x Height............................................................................................................. 21 x 14 x 10 in.
Must Ship Upright......................................................................................................................................... Yes
Electrical:
Power Requirement........................................................................................................... 110V, Single-Phase, 60 Hz
Full-Load Current Rating....................................................................................................................................... 1.8A
Minimum Circuit Size..............................................................................................................................................15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length.............................................................................................................................................. 72 in.
Power Cord Gauge......................................................................................................................................... 18 AWG
Plug Included..........................................................................................................................................................Yes
Included Plug Type................................................................................................................................................ 5-15
Switch Type........................................................................................................ Forward/Reverse & Button Switches
Motors:
Lathe
Horsepower............................................................................................................................................. 1/5 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 1.8A
Speed................................................................................................................................................ 4000 RPM
Type............................................................................................................................................ Universal (DC)
Power Transfer ............................................................................................................................................ Belt
Bearings..................................................................................................... Shielded & Permanently Lubricated
Mill
Horsepower............................................................................................................................................. 1/5 HP
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 1.8A
Speed................................................................................................................................................ 4000 RPM
Type............................................................................................................................................ Universal (DC)
Power Transfer .........................................................................................................................................Direct
Bearings..................................................................................................... Shielded & Permanently Lubricated
The information contained herein is deemed accurate as of 3/30/2023 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 3
Model G0937
Main Specifications:
Lathe Info
Swing Over Bed........................................................................................................................................... 6 in.
Distance Between Centers........................................................................................................................ 10 in.
Swing Over Cross Slide............................................................................................................................... 3 in.
Maximum Tool Bit Size........................................................................................................................... 5/16 in.
Carriage Travel............................................................................................................................................ 7 in.
Cross Slide Travel................................................................................................................................. 2-7/8 in.
Spindle Bore......................................................................................................................................... 11/32 in.
Spindle Taper............................................................................................................................................ MT#2
Number Of Spindle Speeds...................................................................................................................Variable
Spindle Speeds........................................................................................................................ 100 - 2000 RPM
Spindle Type........................................................................................................................ Intrinsic Back Plate
Spindle Bearings........................................................................................................................ Tapered-Roller
Spindle Length............................................................................................................................................. 6 in.
Spindle Length with 3-Jaw Chuck......................................................................................................... 8-5/8 in.
Tailstock Quill Travel................................................................................................................................... 1 in.
Tailstock Taper.......................................................................................................................................... MT#1
Tailstock Barrel Diameter......................................................................................................................... 3/4 in.
Number of Inch Threads................................................................................................................................... 5
Range of Inch Threads..................................................................................................................... 16 - 24 TPI
Mill Info
Mill Taper...................................................................................................................................................MT#2
Mill Spindle Travel................................................................................................................................. 1-1/8 in.
Mill Swing.....................................................................................................................................................4 in.
Distance Spindle To Work Table........................................................................................................... 4-1/2 in.
Maximum Tool Bit Size............................................................................................................................. 3/8 in.
Drilling Capacity For Steel.......................................................................................................................... 8mm
Drilling Capacity For Cast Iron..................................................................................................................10mm
Number of T-Slots............................................................................................................................................ 2
T-Slot Size.............................................................................................................................................. 5/16 in.
T-Slot Centers..............................................................................................................................................2 in.
Drawbar Diameter.................................................................................................................................... 10mm
Drawbar Thread Pitch....................................................................................................................................1.5
Drawbar Length..................................................................................................................................... 5-7/8 in.
Mill Speed Range..................................................................................................................... 100 - 1300 RPM
Construction
Bed..........................................................................................................................Precision-Ground Cast Iron
Headstock............................................................................................................................................ Cast Iron
Body..................................................................................................................................................... Cast Iron
End Gears................................................................................................................................................ Acetal
Paint Type/Finish....................................................................................................................... Powder Coated
Other
Bed Width.............................................................................................................................................. 2-5/8 in.
Carriage Leadscrew Diameter.................................................................................................................. 3/8 in.
Carriage Leadscrew TPI.......................................................................................................................... 16 TPI
Carriage Leadscrew Length.............................................................................................................. 19-3/16 in.
Other Specifications:
Country of Origin ................................................................................................................................................ China
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ........................................................................................................30 Minutes
Serial Number Location .................................................................................................................................. ID Label
Sound Rating ..................................................................................................................................................... 80 dB
ISO 9001 Factory .................................................................................................................................................. Yes
The information contained herein is deemed accurate as of 3/30/2023 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 3 OF 3
Model G0937
Features:
Dual Cross-Slide Mill Table T-Slots
Dual Universal Motors
Variable-Speed Spindles
Precision-Ground Cast-Iron Bed
Push/Pull Fine-Feed Clutch w/Handweel
MT#2 Spindle Taper
MT#1 Tailstock Taper
JT2 Drill Chuck 1/32" - 3/8"
Accessories Included:
Hex Wrenches 2, 3, 4, 6mm
Open-End Wrenches 5.5/7, 8/10mm
Hook Spanner Wrenches 28 - 32, 38 - 42mm
MT#1 Dead Center
Plastic Oil Bottle
3" 3-Jaw Chuck w/Internal & External Jaws
Thread-Cutting Gear Change Set
(2) Chuck Keys
(2) T-Slot Nuts
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Grizzly G0745 Owner's manual
-
-
-
-
Grizzly Industrial G0768Z Owner's manual
-
Grizzly Industrial G0768 Owner's manual
-
-
-
-
