MK 8898
25mm EXTENSION KIT FOR 8800 MODELS
(CT, FR, JM, LS, MK & TT VERSIONS)
INSTALLATION GUIDE
3
SUITABILITY
This extension kit is for use with Connaught (CT), La Chapelle (FR), Janey Mac (JM),
Star (LS), Mackintosh (MK) and Ten Ten (TT).
Professional installation
We recommend that our products are fitted by a
fully qualified professional plumber. They should be
installed correctly and in accordance with all local
water regulations. All products and connections
should be accessible for routine servicing.
About this kit
The standard concealed shower valve is designed
to allow up to a 50mm wall thickness, this
extension kit will enable you to increase the wall
thickness to a maximum of 75mm.
If you have a wall cavity deeper than 70mm to
conceal the valve, we recommend the valve is
secured to a wooden baton on the mounting wall
to reduce the cavity depth (or fit this extension kit
to extend the shower valve by 25mm).
IMPORTANT INFORMATION
70mm
179mm – Connaught (CT)
183mm – La Chapelle (FR)
175mm – Janey Mac (JM)
179mm – Star (LS)
175mm – Mackintosh (MK)
147mm – Ten Ten (TT)
145mm maximum depth
G½ Blanking plug
75mm maximum panel
thickness including tiles
G½ Mounting surface
4
DIMENSIONS OF 8800 MODELS WITH EXTENSION KIT FITTED
Not to scale
Extension kit indicated by shaded area. Shown with Connaught (CT) model.
5
PREPARATION
Exploded view of standard concealed valve. Shown with Connaught (CT) model.
A
B
C
G
F
D
E
1 Unscrew and remove the face place securing
screws. Remove the face plate.
2 Remove the thermostatic control cross handle
‘A’ by unscrewing set screw ‘B’ using a 2mm
hexagonal key.
3 Unscrew and remove screw ‘C’.
4 Pull the temperature override ‘D’ o the
cartridge spline.
5 Remove the thermostatic cartridge cover ‘E’
by unscrewing set screw ‘F’ using a 1.5mm
hexagonal key.
6 Remove the temperature stop ‘G’.
6
J
H
KL
M
INSTALLATION
Exploded view of extended concealed valve. Shown with Connaught (CT) model.
Extension kit components are shaded.
1 Confirm the 38°C temperature setting
(refer to setting instructions in valve
installation guide).
2 Locate the extended temperature stop ‘H’.
3 Assemble the thermostatic cartridge cover ‘E’
to the cartridge cover extension ‘J’ using set
screw ‘F’ and a 1.5mm hexagonal key. Locate
and secure the assembly to the valve body
using set screw ‘K’ and a 1.5mm hexagonal key.
4 Locate the extended override cover ‘L’
(refer to setting instructions in valve
installation guide).
5 Secure the override cover using extended
screw ‘M’.
6 Fit the face plate and secure using the face
plate screws supplied in this kit.
7 Secure cross handle ‘A’ using set screw ‘B’
and a 2mm hexagonal key.
A
B
F
E
Whilst every effort is made to ensure the accuracy of these, they are subject to change without
notice as part of the company’s product development process. The use of trademarks, product design
and artwork is subject to licence or agreement with LBIP Ltd. The design registrations, trademark registrations
and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.
The right to modify designs and dimensions is reserved. LBIP Ltd is a member of ACID (Anti Copying in Design). E&OE
© LBIP Ltd 2022
CONTRACT ENQUIRIES
+44 (0)1992 708 316
info@lefroybrooks.co.uk
CUSTOMER SERVICE, SPARES & TECHNICAL ENQUIRIES
+44 (0)1902 390 894
technical@lefroybrooks.co.uk
LEFROYBROOKS.CO.UK
20.065.150C / MARCH 2022
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Lefroy Brooks FR 8800 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Lefroy Brooks TT 8800 Installation & Servicing Guide
-
Lefroy Brooks MK 8712 Installation & Servicing Guide
-
Lefroy Brooks JL 1222 Installation & Servicing Guide
-
-
-
-
-
Lefroy Brooks CR 1290 Installation & Servicing Guide
-
-