Crestron DIN-EN Installation guide

Crestron
Brand
Crestron
Model
DIN-EN
Type
Installation guide

This manual is also suitable for

Crestron DIN-EN

Below you will find brief product information for Crestron DIN-EN.

Crestron DIN-EN is an enclosure for DIN rail devices. It comes in three sizes and can house two, three, or six DIN rails. Each rail accommodates up to 18 DIN units leaving room for one DIN unit of extra space. The extra space provides room for DIN device locking blocks or wiring along the sides of the enclosure. Each DIN-EN includes a removable front cover for easy access.

The DIN-EN is perfect for Crestron DIN rail products, such as the DIN-AP3, DIN-DALI-2, and DIN-1DIMU4. Third-party DIN rail devices can also occupy space amongst Crestron devices.

Crestron DIN-EN

Below you will find brief product information for Crestron DIN-EN.

Crestron DIN-EN is an enclosure for DIN rail devices. It comes in three sizes and can house two, three, or six DIN rails. Each rail accommodates up to 18 DIN units leaving room for one DIN unit of extra space. The extra space provides room for DIN device locking blocks or wiring along the sides of the enclosure. Each DIN-EN includes a removable front cover for easy access.

The DIN-EN is perfect for Crestron DIN rail products, such as the DIN-AP3, DIN-DALI-2, and DIN-1DIMU4. Third-party DIN rail devices can also occupy space amongst Crestron devices.

DIN-EN Series
Enclosure for DIN Rail Devices
Installation Guide
Internal Dimensions of DIN-EN-2X18 Rail Enclosures
Description
The DIN-EN series of metal enclosures come in three sizes and house two, three, or six
DIN rails. Each rail accommodates up to 18 DIN units leaving room for one DIN unit of
extra space (18 mm). The extra space provides room for DIN device locking blocks or
wiring along the sides of the enclosure. Each DIN-EN includes a removable front cover
for easy access.
The DIN-EN is perfect for Crestron
®
DIN rail products, such as the DIN-AP3, DIN-DALI-2,
and DIN-1DIMU4 (all sold separately). Third-party DIN rail devices can also occupy
space amongst Crestron devices.
Crestron also offers DIN-EN two stage installation products, comprised of rough-in
enclosures and lay-in panels. These products allow for prewiring and rough-in work
during construction and lay-in panel installation later.
2-1/8 in
(55 mm)
11/16 in
(19 mm)
18-15/16 in
(482 mm)
10-7/8 in
(276 mm)
2-1/4 in
(58 mm)
Ground bus
5-3/4 in
(147 mm)
(inside)
5-7/8 in
(150 mm)
5-7/8 in
(150 mm)
(2X) Ø 7/16 in
(Ø 12 mm)
Mounting
holes
Metal, DIN rail,
1-3/8 in (35 mm)
wide x
5/16 in (7.5 mm)
high x
13-1/2 in (342 mm)
long (3x)
(2X) Ø 5/16 in
(Ø 8 mm)
Mounting
holes
(2X) Ø 5/8 in
(Ø 16 mm)
5-3/4 in
(147 mm)
(inside)
1-1/16 in
(27 mm)
10 in
(254 mm)
Ground bus
12 in
(305 mm)
3-1/4 in
(83 mm)
(inside)
5-1/2 in
(140 mm)
(4X) Ø 1/4 in
(Ø 6.4 mm)
Mounting
holes
Metal, DIN rail,
1-3/8 in (35 mm)
wide x
5/16 in (7.5 mm)
high x
13-1/2 in (342 mm)
long (2x)
3-1/4 in
(83 mm)
(inside)
1-1/16 in
(27 mm)
Installation
This section shows exterior and interior dimensions of Crestron’s DIN-EN products.
External Dimensions of DIN-EN-2X18 Rail Enclosures (Front, Side, and Bottom View)
12-5/16 in
(313 mm)
1/8 in
(3.2 mm)
1-3/8 in
(35 mm)
(16x) Ø 7/8 in (23 mm) knockouts for 1/2 in (13 mm)
conduit (same pattern opposite side)
3-9/16 in
(91 mm)
1-5/16 in
(34 mm)
4-3/8 in
(111 mm)
2-15/16 in
(75 mm)
1-3/8 in
(35 mm)
2-15/16 in
(75 mm)
5 in
(127 mm)
3-1/4 in
(83 mm)
1-5/16 in
(34 mm)
11-1/2 in
(293 mm)
14-1/8 in
(359 mm)
5 in
(127 mm)
2-1/4 in
(57 mm)
Additional Resources
Visit the product page on the Crestron website (www.crestron.com) for additional
information. Use a QR reader application on your mobile device to scan the QR image.
DIN-EN-6X18-MMOE DIN-EN-6X18-MMP
DIN-EN-2X18 DIN-EN-3X18 DIN-EN-6X18
DIN-EN-3X18-MMOE DIN-EN-3X18-MMP
~5/16 in
(24 mm)
7-3/16 in
(183 mm)
9-11/16 in
(246 mm)
14-3/8 in
(365 mm)
2-1/2 in
(64 mm)
~1-1/4 in
(32 mm)
2-1/4 in
(58 mm)
1-1/4 in
(32 mm)
Ø 7/8 in (23 mm)
knockouts for
1/2 in (13 mm) conduit
(typical both sides)
16-1/8 in
(409 mm)
24-1/4 in
(616 mm)
23-1/2 in
(597 mm)
4 in
(102 mm)
3-1/16 in
(78 mm)
1/4 in
(7 mm)
3-1/4 in
(83 mm)
4-7/16 in
(113 mm)
1-1/8 in
(28 mm)
knockout
for
3/4 in
(20 mm)
conduit
(typical
both
sides)
External Dimensions of DIN-EN-3X18 Rail Enclosures (Front, Side, and Bottom View)
Internal Dimensions of DIN-EN-3X18 Rail Enclosures
External Dimensions of DIN-EN-6X18 Rail Enclosures (Front, Side, and Bottom View)
16-1/8 in
(409 mm)
39-5/8 in
(1 m)
38-7/8 in
(989 mm)
3-1/16 in
(78 mm)
4 in
(102 mm)
1/4 in
(7 mm)
3-1/4 in
(83 mm)
4-7/16 in
(113 mm)
~5/16 in
(24 mm)
7-3/16 in
(183 mm)
9-11/16 in
(246 mm)
14-3/8 in
(365 mm)
2-1/2 in
(64 mm)
~1-1/4 in
(32 mm)
2-1/4 in
(58 mm)
1-1/4 in
(32 mm)
Ø 7/8 in (23 mm)
knockouts for
1/2 in (13 mm) conduit
(typical both sides)
1-1/8 in
(28 mm)
knockout
for
3/4 in
(20 mm)
conduit
(typical
both
sides)
2-1/8 in
(55 mm)
11/16 in
(19 mm)
34-3/8 in
(873 mm)
10-7/8 in
(276 mm)
2-1/4 in
(58 mm)
Ground bus
5-7/8 in
(150 mm)
4-5/8 in
(118 mm)
(inside)
5-7/8 in
(150 mm)
5-7/8 in
(150 mm)
5-7/8 in
(150 mm)
5-7/8 in
(150 mm)
4-5/8 in
(118 mm)
(inside)
(2X) Ø 7/16 in
(Ø 12 mm)
Mounting
holes
Metal, DIN rail,
1-3/8 in (35 mm)
wide x
5/16 in (7.5 mm)
high x
13-1/2 in (342 mm)
long (6x)
(2X) Ø 5/16 in
(Ø 8 mm)
Mounting
holes
(2X) Ø 5/8 in
(Ø 16 mm)
Crestron Electronics, Inc. Installation Guide - DOC. 7192B
15 Volvo Drive, Rockleigh, NJ 07647 (2030929)
Tel: 888.CRESTRON 06.18
Fax: 201.767.7576 Specications subject to
www.crestron.com change without notice.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered
trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in
the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
~2-1/8 in
(55 mm)
~18-15/16 in
(482 mm)
1-3/4 in
(45 mm)
~10-7/8 in
(276 mm)
23-1/2 in
(597 mm)
(2X) Ø 7/16 in
(Ø 12 mm)
Mounting holes
for up to 1/4 in
screws
(2X) Ø 5/16 in (Ø 8 mm)
Mounting holes for
up to 1/4 in screws
(2X) Ø 5/8 in
(Ø 16 mm)
~11/16 in
(18 mm)
(4X)
Mounting
holes for
MMP panel
~15-3/8 in
(390 mm)
~15/16 in
(24 mm)
~3/8 in
(9 mm)
(4X) Ø 7/16 in
(Ø 11 mm)
(4X)
~5/16 in
(9 mm)
~11-13/16 in
(300 mm)
~2-15/16 in
(75 mm)
~11-13/16 in
(300 mm)
~20-1/4 in
(515 mm)
~13-11/16 in
(347 mm)
~1-9/16 in
(41 mm)
(4X) Ø 3/16 in
(Ø 6 mm)
Mounting holes
for #10 screws
~2-1/8 in
(55 mm)
~34-3/8 in
(873 mm)
1-3/4 in
(45 mm)
~10-7/8 in
(276 mm)
(2X) Ø 5/16 in (Ø 8 mm)
Mounting holes for
up to 1/4 in screws
(2X) Ø 5/8 in
(Ø 16 mm)
~38-7/8 in
(988 mm)
~11/16 in
(18 mm)
(6X)
Mounting
holes for
MMP panel
(2X) Ø 7/16 in
(Ø 12 mm)
Mounting holes
for up to 1/4 in
screws
~15-3/8 in
(390 mm)
~15/16 in
(24 mm)
~3/8 in
(9 mm)
~36-1/8 in
(918 mm)
~13-11/16 in
(347 mm)
~1-9/16 in
(41 mm)
(6X) Ø 7/16 in
(Ø 11 mm)
~11-13/16 in
(300 mm)
(6X)
~5/16 in
(9 mm)
~2-3/8 in
(60 mm)
~11-13/16 in
(300 mm)
(6X) Ø 3/16 in
(Ø 6 mm)
Mounting holes
for #10 screws
~17-11/16 in
(450 mm)
Internal Dimensions of DIN-EN-6X18 Rail Enclosures
Internal Dimensions of DIN-EN-3X18-MMOE (Rough-In Enclosure)
NOTE: The external dimensions of the DIN-EN-3X18-MMOE are identical to the
DIN-EN-3X18 (refer to other side of this sheet).
Dimensions of DIN-EN-3X18-MMP (Lay-In Panel)
Internal Dimensions of DIN-EN-6X18-MMOE (Rough-In Enclosure)
NOTE: The external dimensions of the DIN-EN-6X18-MMOE are identical to the
DIN-EN-6X18 (refer to other side of this sheet).
Dimensions of DIN-EN-6X18-MMP (Lay-In Panel)
This product is Listed to applicable UL
®
Standards and requirements tested by
Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par
Underwriters Laboratories Inc.
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
  • Page 1 1
  • Page 2 2

Crestron DIN-EN Installation guide

Crestron
Brand
Crestron
Model
DIN-EN
Type
Installation guide
This manual is also suitable for

Crestron DIN-EN

Below you will find brief product information for Crestron DIN-EN.

Crestron DIN-EN is an enclosure for DIN rail devices. It comes in three sizes and can house two, three, or six DIN rails. Each rail accommodates up to 18 DIN units leaving room for one DIN unit of extra space. The extra space provides room for DIN device locking blocks or wiring along the sides of the enclosure. Each DIN-EN includes a removable front cover for easy access.

The DIN-EN is perfect for Crestron DIN rail products, such as the DIN-AP3, DIN-DALI-2, and DIN-1DIMU4. Third-party DIN rail devices can also occupy space amongst Crestron devices.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents