AMP Lighting VAC-SLMTIMER1 Installation guide

Brand
AMP Lighting
Model
VAC-SLMTIMER1
Type
Installation guide

This manual is also suitable for

AMP Lighting VAC-SLMTIMER1 is a slimline mechanical timer for indoor use only, designed to be installed in accordance with local codes and the National Electric Code (NEC). It has 125 VAC, 60 Hz ratings and can handle 15A Resistive or general purpose, 1250W Tungsten, 1/2HP. The timer allows setting up to 48 On/Off commands per day, with each pin representing 30 minutes. The arrows on the timer move clockwise and pins that are down represent the times the timer is on, while pins that are up represent the times the timer is off.

AMP Lighting VAC-SLMTIMER1 is a slimline mechanical timer for indoor use only, designed to be installed in accordance with local codes and the National Electric Code (NEC). It has 125 VAC, 60 Hz ratings and can handle 15A Resistive or general purpose, 1250W Tungsten, 1/2HP. The timer allows setting up to 48 On/Off commands per day, with each pin representing 30 minutes. The arrows on the timer move clockwise and pins that are down represent the times the timer is on, while pins that are up represent the times the timer is off.

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
Slimline Mechanical Timer
VAC-SLMTIMER1
AMP
®
Slimline Mechanical Timer
VAC-SLMTIMER1
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This timer is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instruc-
tions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. For indoor use only.
2. Do not use with any device which exceeds capacity of timer.
Ratings: 125VAC, 60Hz.
15A Resistive or general purpose.
1250W Tungsten, 1/2HP
3. Always ensure that device plug is fully inserted into timer.
4. If timer needs cleaning, unplug and wipe with a dry cloth.
5. Do not immerse in water or any liquid.
1
Install Timer to Transformer
Open the transformer and install
the timer into the outlet properly.
If there is a pre-installed timer in
the transformer, remove it before
installing the new timer.
Timer
Outlet
Transformer
[email protected] • 813.978.3900
–3–
1
Set the Time
1
2
3
4
5
6
7
8
9
10
11
2
1
TIME
Before setting your desired
timer functions, twist the timer
so the arrow is pointing to the
current time.
See below for how to use the
timer setting and functions.
Timer Setting and Functions
1
2
3
4
5
6
7
8
9
10
11
2
1
TIME
TIME
Setting On/Off Periods:
Note the arrows on the timer move clockwise.
Each pin represents 30 minutes:
2 pins = 1 hour.
Pins that are down represent the times the timer is on.
Pins that are up represent the times the timer is off.
The timer can set up to 48 On/Off commands a day.
Using your nger, pen or screwdriver pull up all the pins that correspond to
the times you would like the timer to be off. Then make sure the pins are
pushed down for all the times you want the timer on.
Represents timer that will come on
at 8:00PM and shut off at 11:30PM.
Pin
IS-VAC-SLMTIMER1A-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

AMP Lighting VAC-SLMTIMER1 Installation guide

Brand
AMP Lighting
Model
VAC-SLMTIMER1
Type
Installation guide
This manual is also suitable for

AMP Lighting VAC-SLMTIMER1 is a slimline mechanical timer for indoor use only, designed to be installed in accordance with local codes and the National Electric Code (NEC). It has 125 VAC, 60 Hz ratings and can handle 15A Resistive or general purpose, 1250W Tungsten, 1/2HP. The timer allows setting up to 48 On/Off commands per day, with each pin representing 30 minutes. The arrows on the timer move clockwise and pins that are down represent the times the timer is on, while pins that are up represent the times the timer is off.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents