VOLT VAC-TR-CVR1 User manual

VOLT
Brand
VOLT
Model
VAC-TR-CVR1
Type
User manual

VOLT VAC-TR-CVR1 is a slimline transformer pedestal mount with cover, designed for low voltage landscape lighting. It includes a pedestal mount, two 13” XL hammer stakes, two screws, an Allen wrench, and an optional cover. The pedestal mount's stakes can be easily pushed into the ground, and the transformer can be secured to the mount with the included screws. The cover provides additional protection for the transformer from the elements.

VOLT VAC-TR-CVR1 is a slimline transformer pedestal mount with cover, designed for low voltage landscape lighting. It includes a pedestal mount, two 13” XL hammer stakes, two screws, an Allen wrench, and an optional cover. The pedestal mount's stakes can be easily pushed into the ground, and the transformer can be secured to the mount with the included screws. The cover provides additional protection for the transformer from the elements.

VOLT® Low Voltage Landscape Lighting
VOLT® Slimline Transformer Pedestal Mount with Cover
VAC-TR-CVR1 & VAC-TR-MP1-SS
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
VOLT® Slimline Transformer Pedestal Mount with Cover
VAC-TR-CVR1 & VAC-TR-MP1-SS
INSTALLATION INSTRUCTIONS
www.voltlighting.com
Determine the desired location for
mounting the pedestal. Push the
stakes of the pedestal mount into the
ground until ange of stake is ush to
grade. The easiest way to do this is
with your foot directly over the brack-
et the stake is attached to.
NOTE: If the ground is hard and the
stakes are dicult to install, make
two crosscuts in the ground using a at
shovel. Be sure the distance between
the two crosscuts are 7-7/8”, which is
the same as the distance between the
two stakes. This should allow for an
easier installation.
Pedestal
Mount
Stake
Ground
Soil
7-7/8”
A. (1) Pedestal Mount
B. (2) Screws
Remove Mounting Kits from the back of the Pedestal Mount before installation.
C. (1) Allen Wrench
D. (2) 13” XL Hammer Stakes
Install Pedestal Mount
1
Package Contents
Dimensions
26.5”
6”
11”
[email protected] • 813.978.3700
Fit all the slots on the optional cover
to the bolts on the pedestal mount.
Start by removing the upper
screw from the pedestal mount.
Next, loosen the lower screw
on the pedestal mount enough
to allow the transformer tab to
sit on it.This should hold the
transformer in place. Carefully
hold the transformer steady
and reinstall the upper screw
to secure the transformer into
place. Finally, tighten both set
screws until snug.
Pedestal
Mount
Pedestal
Mount
Optional
Cover
Transformer
Allen Wrench
Bolt
Screw
Screw
Plug
Slot
Keyhole
Install Optional Cover
2
Install Transformer
3
IS-VAC-TR-CVR1-VAC-TR-MP1-SS-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

VOLT VAC-TR-CVR1 User manual

VOLT
Brand
VOLT
Model
VAC-TR-CVR1
Type
User manual

VOLT VAC-TR-CVR1 is a slimline transformer pedestal mount with cover, designed for low voltage landscape lighting. It includes a pedestal mount, two 13” XL hammer stakes, two screws, an Allen wrench, and an optional cover. The pedestal mount's stakes can be easily pushed into the ground, and the transformer can be secured to the mount with the included screws. The cover provides additional protection for the transformer from the elements.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents