Tutti Milano TM501 User manual

Brand
Tutti Milano
Model
TM501
Type
User manual

Tutti Milano TM501

This wristwatch features a stopwatch and date display. The stopwatch can measure time up to 59 minutes and 59 seconds in 1/1 second units. To use the stopwatch, press button "A" to start and stop it, and press button "B" to reset it. To set the date, pull the crown out to the 1st position and turn it counterclockwise.

The TM501 also includes a chronograph function, allowing you to measure elapsed time. To use the chronograph, start it by pressing button "A" and stop it by pressing button "A" again. You can reset the chronograph by pressing button "B".

In addition, the Tutti Milano TM501 is water-resistant, so you can wear it while swimming or showering. However, it is important to screw the crown back down into the case to ensure water resistance.

Tutti Milano TM501

This wristwatch features a stopwatch and date display. The stopwatch can measure time up to 59 minutes and 59 seconds in 1/1 second units. To use the stopwatch, press button "A" to start and stop it, and press button "B" to reset it. To set the date, pull the crown out to the 1st position and turn it counterclockwise.

The TM501 also includes a chronograph function, allowing you to measure elapsed time. To use the chronograph, start it by pressing button "A" and stop it by pressing button "A" again. You can reset the chronograph by pressing button "B".

In addition, the Tutti Milano TM501 is water-resistant, so you can wear it while swimming or showering. However, it is important to screw the crown back down into the case to ensure water resistance.

Crown at normal position
Crown at 1st position
Crown at 2nd position
Hour hand Minute handSecond hand
A
B
SETTING THE TIME
1 First unlock the crown by turning it counterclockwise
2 Pull the crown out to the 2nd position
3 Turn the crown to set hour and minute hands
4 After the time has been set, crown must be screwed back down into
the case to ensure water resistance
SETTING THE DATE
1 First unlock the crown by turning it counterclockwise
2 Pull the crown out to the 1st position
3 Turn the crown counterclockwise to set the date*
* If the date is set between the hours around 9:00 PM and
1:00 AM, the date may not change the following day
4 After the data has been set, push the crown back, crown must be
screwed back down into the case to ensure water resistance
Date
Start / Stop button stopwatch
Split / Split release / Reset button
stopwatch
TM501 MANUAL
FITTING METHoD oF
HANDS
Place the module on case back shown in the figure and
position the reference hand, then fit the hands according
to the following procedure
1 First unlock the crown by turning it counterclockwise
2 Pull out the crown to the time setting position.
3 Turn the crown to the left, and stop it just after the date
changes. After the date starts changing, Turn the crown
slowly
4 Push in the crown by one step, taking care not to turn it.
5 Fit the reference hand,hour hand and minute hand to the
12-o’clock position
6 Push the crown back, crown must be screwed back
down into the case to ensure water resistance
When fitting the hands, remove the case back and place
the movement on work stand. These specifications might
be changed without prior notice
cHroNoGrApH rESET
(INcL. AFTEr rEpLAcING BATTErY)
This procedure shoud be performed when the chronograph
second hand do not return to the 0 second position after
the chronograph has been reset, and including after the
battery has been replaced
1 First unlock the crown by turning it counterclockwise
2 Pull the crown out to the 2nd position.
3 Press button “A” to set the chronograph second hand to
the 0 position
4 The chronograph hands can be advanced rapidly by
continuously pressing button “A”
5 Once the hands have been zeroed, reset the time and
push the crown back, crown must be screwed back
down into the case to ensure water resistance
* Do not return crown to normal position while chrono-
graph second hand return to 12:00 (ZERO) position.
Hand stops on the way when crown are returned to
normal position and these positions are recognized as
12:00 (ZERO) position
USING THE
cHroNoGrApH
This chronograph is able to measure and display time in
1/1 second united up to maximum of 59min 59sec
Measuring time with the chronograph
1 The chronograph can be started and stopped each time
button “A” is pressed
2 Pressing button “B” resets the chronograph and all
hands return to their 0 positions
Reset (B)
Start time measurement (A) Stop (A)
TM501 MANUAL
  • Page 1 1
  • Page 2 2

Tutti Milano TM501 User manual

Brand
Tutti Milano
Model
TM501
Type
User manual

Tutti Milano TM501

This wristwatch features a stopwatch and date display. The stopwatch can measure time up to 59 minutes and 59 seconds in 1/1 second units. To use the stopwatch, press button "A" to start and stop it, and press button "B" to reset it. To set the date, pull the crown out to the 1st position and turn it counterclockwise.

The TM501 also includes a chronograph function, allowing you to measure elapsed time. To use the chronograph, start it by pressing button "A" and stop it by pressing button "A" again. You can reset the chronograph by pressing button "B".

In addition, the Tutti Milano TM501 is water-resistant, so you can wear it while swimming or showering. However, it is important to screw the crown back down into the case to ensure water resistance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents