CAME amico Installation guide

Brand: CAME

Model: amico

Category: Gate Opener

Type: Installation guide

AMICO SERIES

INSTALLATION MANUAL

A1824U

AUTOMATION FOR SWING GATES

Pag. 2 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

IMPORTANT UL-325 SAFETY INSTRUCTIONS

A1824U

It is extremely important that all parties involved in the installation and operation of the gate operator system read and understand

the following warning instructions.

WARNING – To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with gate controls. Keep the remote control away from children.

3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.

4. Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object activates

the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and

retest the gate operator properly can increase the risk of injury or death.

5. Use the emergency release only when the gate is not moving.

6. KEEP GATES PROPERLY MAINTAINED. Read the installation manual and have a qualified service person make repairs

to gate hardware.

7. The entrance is for vehicles only. Pedestrians must use separate entrance.

8. SAVE THESE INSTRUCTIONS.

Instructions regarding intended installation of the gate operator.

A. Install the gate operator only when:

1. The operator is appropriate for the construction of the gate and the usage Class of the gate.

2. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of

4 feet (1.22m) above the ground to prevent a 2-1/4 inch (57.2mm) diameter sphere from passing through the

openings anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open

position.

3. All exposed pinch points are eliminated or guarded.

4. Guarding is supplied for exposed rollers.

B. The operator is intended for installation only on gates for vehicles. Pedestrians must be supplied with a separate access

opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that

persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.

C. The gate must be installed in a location so that enough clearance is supplied betweehbe employed, and adjacent

structures when openening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.

D. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.

Do not over-tighten the operator clutch or pressure relief valve to compensate for a damaged gate.

E. For gate operators utilizing Type D protection:

1. The gate operator controls must be placed so that the user has full view of the gate area when the gate is not

moving.

2. The placard provided marked in letters at least 1/4 - in (6.4mm) high with the word “WARNING” and the

following statement or equivalent: “Moving Gate Can Cause Serious Injury or Death” shall be placed adjancent

to the controls.

3. An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed.

4. No other activation device shall be connected.

Pag. 3 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

F. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet (1.22m)

above the ground to prevent a 2-1/4 inch (57.2mm) diameter sphere from passing through the openings anywhere in the gate,

and in that portion of the adjacent fence that the gate covers in the open position.

G. All exposed pinch points are eliminated or guarded.

H. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent

structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access area.

I. Controls intended for user activation must be located at least six feet (6’) away from any moving part of the gate and

where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily

accessible controls shall have a security feature to prevent unauthorized use.

K. FOR GATE OPERATORS UTILIZING A NON-CONTACT SENSOR:

1. See instructions on the placement of non-sontact sensors for each type of application.

2. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while

the gate is still moving

3. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as

the perimeter reachable by a moving gate or barrier.

L. FOR A GATE OPERATOR UTILIZING A CONTACT SENSOR:

1. One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as the

leading edge, trailing edge, and post mounted both inside and outside of a vehicular horizontal slide gate.

2. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.

3. One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate.

4. A hardwired contact sensor shall be located and its wiring arranged so that the communication between the

sensor and the gate operator is not subjected to mechanical damage.

5. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate.

Additionally, if the bottom edge of a swing gate is greater than 6 inches (152mm) above the ground at any

point in its arc of travel, one or more contact sensors shall be located on the bottom edge.

M. A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.

a. Power should be disconnected before installing or servicing a gate operator.

b. All electrical wiring should comply with all local building and electrical codes.

c. All entrapment zones and pinching points should be covered.

d. All safety devices should be tested to assure their proper functionality.

e. The operation of the gate system: operator, controls and safety devices should be reviewed with the end user

or owner, who should be informed of the need for periodic maintenance of the safety and control equipment.

f. All installation operating and safety manuals should be left with the owner.

N. All gate operators systems should include safety devices such as reversing edges or photocells in order to provide

added protection. These safety devices should be installed in accordance to the design and application of the system

being installed.

O. A qualified professional installer should install a gate operator system, its safety accessories and should observe these

minimum procedures:

Pag. 4 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

CAME AMERICAS AUTOMATION, LLC

MANUFACTURER’S LIMITED 3-YEAR WARRANTY

Veriﬁcation of the warranty period requires copies of receipts or other proof of purchase.

Warranty cannot be honored without proof of purchase. Please retain these records.

Came Americas Automation, LLC (“CAME®”) products are warranted by CAME® against defects in materials and manufacturer

workmanship for a period of thirty-six (36) months from the date of purchase, provided the recommended installation manual and

procedure have been followed. CAME®’s sole obligation under this warranty is limited to repairing or replacing, at our option, any

parts which shall be determined by CAME® to be defective, and is conditioned upon CAME® receiving notice of any such defect

within the warranty period. Claims under this warranty may only be made by a purchaser of CAME® products (the “Customer”).

CAME® reserves the right to make the ﬁnal determination as to whether there is a defect in the materials and/or workmanship, and

whether or not a product is within the warranty period. CAME® is not responsible for any damages or other costs caused by, or which

may result from installation, handling, non-recommended operation, product abuse, or modiﬁcations not authorized by CAME® or for

any damages which may arise out of the use of CAME® products.

CAME® sells its products through authorized distributors. This warranty on CAME® products is NOT VALID if the products have been

purchased from an unauthorized distributor, reseller, online E-tailer ( e.g., E-bay®), or if a product serial number has been altered,

removed, or replaced in any way. To verify that you are buying from an authorized CAME distributor or reseller please

call +1 305-433-3307.

In the case of product failure due to defective material or manufacturer workmanship within the thirty-six (36) months warranty

period, the product will be repaired or replaced (at the manufacturer’s option) at no charge to the Customer, if returned, freight

prepaid, to CAME AMERICAS AUTOMATION, LLC, 11345 NW 122nd Street Medley, Florida 33178.

IMPORTANT: Obtain a Return Goods Authorization (RGA) number before returning item(s) to our facilities by submitting a warranty

claim and request for RGA with our customer service department. Products shipped without an RGA number will not be accepted.

Replacements or repaired parts are covered by this warranty for the remainder of the thirty-six (36) month warranty for the original

product or six (6) months from the date of repair or replacement, whichever is greater. CAME® will pay shipping costs at the ground

transport rate for the return to owner of item(s) repaired under warranty.

The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair, or the

reinstallation of these parts after repair. Use of any (00021996.doc V.2) components that are not CAME® speciﬁed (e.g. batteries, light

bulbs, drive belts, chains or transformers) will void the warranty. This warranty shall be void if damage to the product(s) was due to

improper installation or use, neglet, accident, use of non-CAME® speciﬁed or approved components or replacement parts, connection

to an improper power source, tampering, or if damage was caused by lighting, strikes, power surges, wind, ﬁre, ﬂoor, insects, or other

natural agents or disasters.

This warranty gives you specific legal rights, and you may also have other rights, which vary from

state to state (or jurisdiction to jurisdiction.) CAME's responsibility for malfunctions and defects in

equipment is limited to repair and replacement as set forth in this warranty statement.

THE CUSTOMER ACKNOWLEDGES AND AGREES THAT THIS WARRANTY IS MADE

EXPRESSLY IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES FOR THE

PRODUCT(S), INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES AND

CONDITIONS OF MERCHANTABLE QUALITY, MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, OR ANY OTHER EXPRESS OR IMPLIED WARRANTY ARISING

OUT OF LAW, STATUTE, USAGE OF TRADE OR COURSE OF DEALINGS.

The warranty hereunder is limited in time to the term of the limited warranty period reflected in this

limited warranty. No warranties, whether express or implied, will apply after the limited warranty

period has expired. Some states do not allow limitations on the term of an implied warranty, so this

limitation may not apply to you.

Pag. 5 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Be sure that the circuit breaker for the line input power is turned off before connecting the input power to the unit.

Warning: CAME SPA is not responsible for researching and complying with local building codes. Be sure to check these

codes before installation.

The installer must use 14AWG conductors and ½” conduit for the power connection.

Power Connection

CAUTION

CLASS DESCRIBTION DUTY CYCLE A1824U

IResidential Vehicular Gate Operator

Typical use: Home, 1-4 apartment condominium.

Limited public access. Continuous X

II Commerical/ General Access Vehicular Gate Operator

Typical use: Condominiums, hotels, parking lots.

No general public access. Continuous X

III Industrial/ Limited Access Vehicular Gate Operator

Typical use: industrial location, Factory, Loading Dock.

No general public access. Continuous X

IV Restricted Access Vehicular Gate Operator

Typical use: Security area with restricted access.

No general public access. Continuous X

CAME AUTOMATION GATES UL 325 CLASSES

CAME® DOES NOT ASSUME, AND SPECIFICALLY DISCLAIMS, ANY LIABILITY OR OBLIGATION WHATSOEVER IN THE SALE OF THE

PRODUCT(S), INCLUDING ANY LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES TO YOU OR ANY OTHER

PERSON OR ENTITY, INCLUDING, WITHOUT LIMITATION, ANY LIABILITY FOR THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES. THE

CUSTOMER ACKNOWLEDGES THAT THIS LIMITED WARRANTY PROVIDED IN LIEU OF ALL OTHER WARRANTIES AND CUSTOMER’S

WAIVER OF SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES IS COMMERCIALLY NECESSARY AND REASONABLE, AN ESSENTIAL

AND MATERIAL ELEMENT OF THIS TRANSACTION, AND UPON WHICH BOTH THE CUSTOMER AND CAME® HAVE RELIED AND HAVE HAD

THE OPPORTUNITY TO NEGOTIATE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. CAME®‘s liability will be no more than the amount you paid for the product that is the subject of a claim.

This is the maximum amount recoverable under this warranty. The limitations in this section shall apply whether or not the alleged

breach or default is a breach of a fundamental or material condition or term, or a fundamental or material breach.

-4°F

131°F

Pag. 6 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

4.1 Gate Operator

4 Description

2.1 Intended use

1 Legend of symbols

This symbol tells you to read the section with particular care.

This symbol tells you that the sections concern safety issues.

This symbol tells you what to say to the end-users.

2 Intended use and application

The A1824U operator is designed to automate swing gates used in residential or condominium settings.

The use of this product for purposes other than those described above and installation executed in a manner other

than as instructed in this technical manual are prohibited.

3 Reference Standards

“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”

“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”

“THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS”

2.2 Applications

This product is engineered and manufactured by CAME cancelli automatici s.p.a. and complies with current safety regulations.

The gearmotor is made up of two aluminium alloy half shells housing the Encoder gearmotor - which features an electric blocking

mechanism - and an epicyclical reduction system with endless screw.

4.2 Technical features

Control board power supply: 120V A.C. 50/60Hz

Motor power supply: 24V D.C.

Max draw: 4A

Power: 1/3 Hp

Adjustable thrust: 400 - 2000N

Opening time (90°): Adjustable

Gear ratio: 1/36

Duty Cycle: Intensive use

Protection Rating: IP44

Weight: 16.5 lbs.

The company CAME cancelli automatici s.p.a. is ISO 9001:2000 quality certified; it has also obtained the ISO 14001 environmental

safeguarding certification. Came engineers and manufactures all of its products in Italy.

This product complies with the following standards: UL-325 and CSA C22.2 NO.247-92.

Length of gate leaf 3 ft 5 ft 6 ft

Weight of gate leaf 551 lbs 474 lbs 441 lbs

-4°F

131°F

-4°F

131°F

35” in

6” in

3.4” in

29” in

12” in

(inches)

Pag. 7 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

4.4 Dimensions

4.3 Description of parts

A1824U

1) Operator

2) Pilaster bracket

3) Gate bracket

4) Screw, bushing and nut for the pilaster bracket

5) Bolt and nut for the gate bracket

6) Pin distancer

5 Installation

Before installing, do the following:

• Make sure you have suitable tubing and conduits for the electrical cables to pass through and be protected against mechanical

damage.

• Fit tubing to drain away any water leaks which may cause oxidation.

• Make sure that any connections inside the case (that provide continuance to the protective circuit) be fitted with extra insulation

as compared to the other conductive parts inside.

• Make sure the structure of the gate is sturdy, the hinges work and that the is no friction between moving and

non-moving parts.

• Make sure there is a mechanical stop for opening and closing.

Installation must be carried out by expert qualified personnel and in full compliance with current regulations.

5.1 Preliminary checks

Pag. 8 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and compliance with

the current standards and regulations. The following figure illustrates the minimum equipment needed by the installer.

Note: If the cable length differs from that specified in the table, then you must determine the proper cable diameter in the basis of the

actua l power draw by the connected devices. For connections that require several, sequential loads, the sizes given on the table must

be re-evaluated based on actual power draw and distances. When connecting products that are not specified in this manual, please

follow the documentation provided with said products.

5.3 Cable list and minimum thickness

Connections Type of cable Length of cable

3 < 32 ft

Length of cable

32 < 65 ft

Length of cable

65 < 100 ft

Control panel power supply 120V

UL LISTED

CABLE/WIRE

3G x 14AWG 3G x 14AWG 3G x 14AWG

Motor power supply 24V 3G x 14AWG 3G x 14AWG 3G x 14AWG

Flashing light 2 x 20AWG 2 x 20AWG 2 x 20AWG

Photocell transmitters 2 x 20AWG 2 x 20AWG 2 x 20AWG

Photocell receivers 4 x 18AWG 4 x 18AWG 4 x 18AWG

Accessories power supply 2 x 20AWG 2 x 20AWG 2 x 20AWG

Control and safety devices 2 x 20AWG 2 x 20AWG 2 x 20AWG

Antenna RG58 max. 32 ft

5.2 Tools and materials

1) A1824U operator

2) Control panel

3) Reception antenna

4) Flashing light

5) Selector switch

6) Photocells

7) Electric cable junction box

8) Mechanical gate stops

5.4 Standard installation

28.3

23.2

28.3

(inches)

Pag. 9 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Warning: After establishing the best point to which you will secure the gate bracket, secure the bracket to the pillar and make sure the

quotas shown in the table below are met.

Note: By increasing measurement B, the opening angle and gate speed are reduced. While the gearmotor thrust is increased by

increasing the measurement A, the opening angle and gate speed increases, while the gearmotor thrust is decreased.

Opening A

(in)

90° 5.11 5.11 2.3

120° 5.11 4.3 1.9

Ideal securing

point

Gate bracketPillar bracket

Lay the corrugated tubing needed for the connections deriving from the junction box.

Note: The number of tubes depends on the type of system and accessories employed.

The following illustrations are only examples, given that the space available for anchoring the operator and accessories may vary

from gate to gate. It is up to the installer, thus, to choose the most suitable solution.

5.5 Installing the operator

Electric cable junction box

Pag. 10 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Assemble and weld the two parts of the pillar bracket. Secure the bracket to the point you have chosen with proper plugs and screws

or - if the pillar is made of metal - weld it on.

Weld the gate bracket to the gate leaf making sure the quotas shown in the table are met.

Note: On non-metal gate leaves assemble and weld the two parts of the bracket and secure them with proper screws. Secure the tail

joint to the bracket.

Tail joint

Screw M8 x 35

Insert the bushing (lubricated) into the pillar bracket’s hole. The bracket has holes that allow the opening angle to be changed. Secure

the tail joint to the bracket.

Bushing

Nut UNI 7474 M8

Pag. 11 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Attachment pin

Washer

Nut M12

Bushing

Insert the bushing onto the main lug as shown in the drawing.

Attachment pin

Open the gate to the max opening position, place the mechanical stop against it with the pin attachment and ﬁx it in place.

Slotted hole

Open the gate leaf, insert the faceted anchoring lug into the slotted hole in the head bracket and tighten it using the (1) issued

washer and nut or, alternatively, release the gearmotor (see manual release paragraph), remove the head cover and move the faceted

anchoring lug using a screwdriver until it lines up with the slotted hole, then secure it.

(2) Procedure to carry out even when lubricating the endless screw (see maintenance paragraph)

Warning: Make sure that the anchoring lug is perfectly inserted in line with the slotted hole.

Loosen the nuts of the mechanical stops.

ENC

B1 B2

10 11 E1 1 2 3 3P 4 5 7 CX CY TS

LNM1 N1

ENC1

M2 N2

ENC2

ENC

Pag. 12 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Slide open the small door that protects the release, insert the tri-lobed key (part # 119RY077) and turn it.

5.6 Manual release of the gearmotor

For the electrical connection procedures, use the junction box and branching boxes.

5.7 Connecting to the control panel

Power

120V a.c. - 50/60 Hz

Connecting the 24V d.c. delayed

closing gearmotor

Connecting the 24V d.c. delayed

opening gearmotor

ZLJ24U Control panel

Close the gate leaf, loosen the nuts on the closing mechanical stop, place it up against the attachment pin, then secure it.

B1 B2

10 11 E1 1 2 3 3P 4 5 7 CX CY TS

LNM1 N1

ENC1

M2 N2

ENC2

ENC

Pag. 13 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

5.8 Outward opening installation

Opening A

(in)

90° 5.11 5.11 28.3

Weld the extra bracket to that of the pillar, secure the extra

bracket to the pillar making sure the A and B quotas are met

as shown in the table. Open the gate to a 90° arc, weld or

secure using proper screws the gate bracket making sure the

E measurement is met.

Secure the gearmotor to the brackets.

Connect the gearmotors to the panel as shown in the diagram.

Pillar bracket

Extra bracket

Gate bracket

Power

120V a.c.

50/60 Hz

Extra bracket

Delayed

closing

action

Delayed

opening

action

Pag. 14 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

6 Safety instructions

This product must only be employed for its originally intended use. The automation installation using these gearmotors requires

adequate safety systems on the gate leaves to detect any obstacles (e.g. sensitive edges), in compliance with UL325 standards and

CSA C22.2 No.247 for both the US and Canada. Any other use is wrong and potentially dangerous. The manufacturer cannot be held

liable for any damages resulting from wrongful, erroneous or negligent uses.

Avoid working close to the hinges or other moving mechanical parts. Stay out of the opening/closing arc when operator is in motion.

Do not exercise force against the motion of the operator as this could result in potentially dangerous situations.

Important safety instructions

Do not allow children to play or loiter within the opening/closing arc of the operator.

Keep remote controls and any other command device out the reach of children, to prevent operator from being activated by accident.

In the event of anomalous behaviour, stop using the operator immediately.

Danger of crushing hands

Danger of crushing feet

Danger! High voltage

No transit during operation

Pag. 15 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

Periodic maintenance to be carried out by the end-user is as follows: Wipe clean the glass surface of the photocells; check that

the safety devices work properly; remove any obstructions.

We suggest checking the state of lubrication and tightness of the anchoring screws on the operator.

To check the efficiency of the safety devices, move an object in front of the photocells when gate is closing.

If the operator inverts the motion or stops, the photocells are working properly.

This is the only maintenance procedure to be carried out with the power source connected.

Before performing any maintenance procedures, cut off the main power, to prevent possible accidents due to gate movement.

To clean the photocells use a water dampened cloth. Do not use solvents or other chemical products which may ruin

the devices.

In the event of any strange vibrations or squeaking, lubricate the joints with grease, as shown in the diagram.

Lubricate the worm screws through the slits in the pressure die-cast. To do this, remove the head cover (fig. A).

Make sure there are no plants within the photocell’s beam, and that the gate motion is free of any obstacles.

7 Maintenance

7.1 Periodic maintenance

MALFUNCTIONS POSSIBLE CAUSES CHECK AND REMEDIES

The gate will not open

nor close

• There is no power

• The gearmotor is released

• The transmitter’s batteries are run down

• The transmitter is broken

• The stop button is either stuck or broken

• The opening/closing button or the selector switch are stuck

• If not using EMERGENCY stop botton

• If not using PHOTOCELLS.

• Check that the power is up

• Call assistance

• Replace batteries

• Call assistance

• Jump between 2-1

• Jump N/C contacts if not used.

The gate opens but

will not close

• The photocells are engaged • Check that photocells are clean

and in good working order

• Call assistance

The Flashing light

does not work

• The bulb is burnt • Call assistance

7.2 Trouble shooting

Fig.A Slits

Pag. 16 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

7.3 Extraordinary maintenance

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________

__________________________________________________________________________________________________

The following table serves to note down any extraordinary maintenance, repairs or improvements performed by specialised firms.

Note: Any extraordinary maintenance must be performed by specialised technicians.

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________

__________________________________________________________________________________________________

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________

__________________________________________________________________________________________________

Extraordinary maintenance log

Date Notes Signature

Periodic maintenance log for end-user (every 6 months)

Pag. 17 - Manual code: 119DV30 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

CAME Cancelli Automatici S.p.A. employs a UNI EN ISO 14001 certified and compliant environmental protection system at

its plants, to ensure that environmental safeguarding.

We ask you to keep protecting the environment, as CAME deems it to be one of the fundamental points of its market operations

strategies, by simply following these brief guidelines when disposing.

DISPOSING THE PACKING MATERIALS

The packing components (cardboard, plastic, etc.) are solid urban waste and may be disposed of without any particular difficulty, by

simply separating them so that they can be recycled.

Before actions it is always advisable to check the pertinent legislation where installation will take place.

DO NOT DISPOSE OF IN NATURE!

DISPOSING OF THE PRODUCT

Our products are made using different types of materials

The majority of them (aluminium, plastic, iron, electric cables) can be considered to be solid urban waste

They may be recycled at authorised firms

Other components (electrical circuit board, remote control batteries etc.) may contain hazardous waste.

They must, thus, be removed and turned in to licensed firms for their disposal.

Before acting always check the local laws on the matter.

DO NOT DISPOSE OF IN NATURE!

8 Phasing out and disposal

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________

__________________________________________________________________________________________________

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________

__________________________________________________________________________________________________

CAME Cancelli Automatici S.p.A.

via Martiri della Libertà, 15

31030 Dosson di Casier - Treviso - ITALY

tel (+39) 0422 4940 - fax (+39) 0422 4941

internet: www.came.it - e-mail: [email protected]

Intertek Testing Services NA Inc.

165 Main Street, Cortland, NY 13045

Telephone 800-345-3851 or 607-753-6711 Fax 607-756-6699

Standard for Door, Drapery, Gate, Louver, and Window Operators and Systems, UL 325 - 5th edition,

Issued 06/07/2002. Revised 08/29/2007.

Standard(s):

Standard for Operators and Systems of Doors, Gates, Draperies and Louvres, CSA C22.2 No. 247.

Issued 12/01/1992 (R2004), General Instruction No. 1

Product: Vehicular Horizontal Swing Gate Operators

Models: AXO Series: Models AX 5024U and AX 3024U

AMICO Series: Model A 1824U

FROG Series: Models A 24U and FROG JU

THIS PAGE LEFT INTENTIONALLY BLANK

CAME AMERICA AUTOMATION, LLC

11345 NW 122nd ST

MEDLEY FL 33178

Tel (305)433-3307

Fax (305)396-3331

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.