Jacfit JMate Strap User manual

Type
User manual
More info on the website,
Jact.com
JMate
JMate strap x 2 (260mm/290mm)
USB charging cable
① ②
2. Turn on Location and Bluetooth on mobile setting. Allow Jacfit
app to use them while rst download.
3. Open the Jact app and enter “Boxing” mode.
4. Knock JMate to wake up. When
the LED indicator lights up
“Green”, you will see the sensor
ID appears on the Bluetooth
setting.
5. Click the ID and press “Connect”
to Boxing mode. If connected,
the indicator light will become
“Blue”.
Scan QR code to download the
Jact App
iOS Android
Charging
1. Attach the small end of the USB cable to the
magnetic charging port on your device.
2. Plug the large end of the USB cable into a
USB charging port.
3. LED indicator will light up “Red” until
charging is completed. Note: When indicator
flashes "Green" means battery is low.
Please charge.
Installation
1. Align JMate and
strap with Jact
logo.
2. Connect them with
hook magic tape.
JMate Boxing Mode
1. Knock JMate and check
the indicator light. Wear
it on your “Right wrist”
and the indicator light
side facing you.
Boxing
RunBike
Bluetooth Setting
Device list
JMate
Connect
Skip
"Jact" Would Like to
Use Bluetooth
OKDon't Allow
Jact requries to use Bluetooth to
connect with the device
Cast your screen to TV for a wonderful experience
Regular TV: Using a HDMI cable and an adapter for your phone.
Smart TV: Connect to the Wi-Fi and use airplay or chromecast.
FCC Caution:
Any changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This device and its antenna(s) must
not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT NOTE
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two
conditions:(1) this device may not cause harmful interference,and (2) this device must accept
any interference, including that which may cause undesired operation.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment.
This equipment has been tested and found to be compliant with the limits for a Class B digital
device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and radiates radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception (which can
be determined by turning the equipment o and on) the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected
-Consult the dealer or an experienced radio / TV technician for help
FCC Interference Statement
Casting Calibration
1. If you cast the Jacfit app
to TV, please go to the app
setting and choose “Casting
Calibration”.
2. Watch casting screen and cross when
boxing icon down to the blue area.
3. Adjust the time to make sure your
score achieves at least 12.
JMate Step Coin Mode
1. During “Step Coin Mode”, no
need to connect to the app.
Wear JMate on any wrist, you
are ready to go.
2. When connected, JMate will
upload your data and convert it
to Jcoins once you click “Exchange” .
Total steps
New steps
Total Jcoins
exchanged
Exchange
Jcoins
f
Score
Casting Calibration
/15
Casting Calibration
Copyright Aug. 2022
  • Page 1 1
  • Page 2 2

Jacfit JMate Strap User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI