2. Atdec
  3. TH-2250-VTP
TH-2250-VTP

Atdec TH-2250-VTP User manual

  • Hello, I'm your chat assistant. I've reviewed the installation instructions for the Telehook TH-2250-VTP wall mount. This document provides detailed guidance on mounting the bracket and attaching your display, including tilt adjustment. I am ready to answer any specific questions you have about this product or the installation process.
  • What is the maximum weight that the Telehook Wall Mount can support?
    What VESA hole configurations are supported by this mount?
    Can the display be tilted after being mounted?
Component Checklist
Step 1. Component Checklist
Check you have received all parts against the Component Checklist above.
Hardware
Mounting Fasteners
Step 2. Remove the Wall Bracket Cover
TH-2250-VTP

TM
Installation Instructions
[B] Nylon
Anchor (x2)
[C] M4 Washer (x4)
[D] M5 Washer (x4)
[A] Wall Mount
Screw (x2)
Flat Screen Wall Mount | Tilt
[J] M6x8mm / [K] M6x12mm (x4 each)
[F] M4x8mm / [G] M4x12mm (x4 each)
[H] M5x8mm / [I] M5x12mm (x4 each)
[E] M6 Washer (x4)
TOOLS REQUIRED:

ps Head Screw Driver
3/16”) Drill Bit
5/16”) Masonry Drill Bit
Remove the two Locking Screws,
on both left and right sides.
Step 3. Remove the Mounting Plate
Step 4. Fix the Wall Bracket to the Wall
Using the Wall Plate as a drilling template, choose from one of the following Mounting options, 7LPEHU6WXG250DVRQU\:DOO.
'ULOOWZRKROHVPP
GHHSZLWKDPP
GULOOELW
Masonry Wall
Nylon Anchor
(x2)
Wall Mount Screw (x2)
Wall Plate
M6 Washer (x2)
Wall Plate
Wall Mount Screw (x2)
M6 Washer (x2)
Timber Stud
'ULOOWZRKROHVPP
GHHSZLWKDPP
0DVRQU\GULOOELW
LIFT
TH-2250-VTP
(fully assembled)
IMPORTANT INFORMATION
,03257$17,QVWDOO7HOHKRRN:DOO0RXQWDVSHU,QVWDOODWLRQ,QVWUXFWLRQV
! Telehook Wall Mount supports Displays weighing up to 30kg (66lbs), with VESA hole configurations:
50x50mm, 75x75mm, 100x100mm, 200x100mm, 200x200mm.
! The Manufacturer accepts no responsibility for incorrect installation.
Cover
Locking
Screw (x2)
PULL
PULL
Step 6. Fasten the Mounting Plate to your Display
Mounting Screw (x4)
Choose appropriate Mounting Screws
and Washers from the Hardware
supplied to suit your Display.
Washer (x4)
Top of
Display
Mounting Plate
Step 7. Attach the Display to the Wall
Step 8. Tilt Adjustment
Locking
Screw (x2)
Hook the Mounting Plate
onto the Wall Bracket.
Wall Bracket
Mounting Plate
Re-insert the two
Locking Screws
on boths sides.
Display
bb
( required)
Tighten the Lever to lock the
Display in the desired position.
Step 5. Reinstall Wall Bracket Cover
Push the two pieces of
the Cover together.
PUSH
PUSH
TILT
TILT
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 17.01.11 ©
LOOSEN
Loosen the Lever before adjusting tilt.
TIGHTEN
Lever
LOWER
/