Spycentre Security 6762 Quick start guide

Brand: Spycentre Security

Model: 6762

Category: Watches

Type: Quick start guide

SpyCentre Security® Since 1993 1-800-292-7748

6762 – Multi-Functional Digital Voice Recorder Watch with Bluetooth

How to charge the battery:

● Plug the device into a computer or USB wall charger using the included Micro USB

cable. The battery indicator on the screen will show a full green battery when fully

charged.

● It takes 1 hour to fully charge

● Flashing battery indicator bar = Charging

● Full battery indicator bar = Fully charged

How to record an audio file instantly:

● Press and hold the on and off buttons, and the device will turn on

● Press and hold the menu button "M," and the device will begin recording

● To enter the recording screen once the display disappears, tap any button two times

● To save the recording, tap the "M" menu button

● Tap the menu button "M" to make another recording

● To turn it off, press and hold the on and off button

Note: 20 seconds after a recording has begun, the time on the watch will return and 10

sec later will disappear. Tap any button to display the time for 10 seconds.

How to record an audio file by navigating the menu:

● Press and hold the on and off buttons, and the device will turn on

● Navigate the menu with the "Up" and "Down" buttons

● Select the “Recordings” menu option by taping the menu button "M"

● Highlight “Start Voice Recording” and tap the menu button "M"

● A please wait screen will appear, followed by a recording screen. The device is now

recording

● To enter the recording screen once the display disappears, tap any button two times

● To save the recording, tap the menu button "M"

● Tap the menu button "M" again to make another recording

● To turn it off press and hold the on and off buttons

How to set voice-activation:

● Select the "Recordings" section of the menu with the menu button "M"

● Highlight "Record Set," then tap the menu button "M"

● Highlight the "AVR" set, then tap the menu button "M"

● Highlight and select with the menu button "M"

● AVR switch = Voice activation on or off

● AVR level = Adjusts the mic sensitivity

● AVR delay = Delay of recording

● Once completed, press and hold the menu button "M" to return to the main menu

● Create a new recording. In the recording screen will be a VOS in red, indicating the

device is now in voice-activated recording mode

Note: Voice activation will not extend the battery life of the device.

How to set the recording schedule:

Changing this setting will allow the device to only record during the set times

● Select the "Recordings" section of the menu with the menu button "M"

● Highlight "Record Set," then tap the menu button "M"

● Highlight "Auto Record," then tap the menu button "M"

● Highlight and select with the menu button "M"

● Record on/off = Turn on or off the schedule record mode

● Auto Recycle = Record one time or every day

● Start time = What time to begin recording

● End time = What time to end recording

● Use the "Up" and "Down" arrows to adjust the hour, then hold down either of those

buttons to switch to the minutes and tap the menu button "M" when done

● Once completed, press and hold the menu button "M" to return to the main menu

Note: If the device runs out of power during the recording, it will finalize and save the file

before the battery dies.

Buttons :

● Up and down buttons for navigating up and down, left and right between options in menu

settings

● The "M" button is the mode, menu, enter, yes, and confirm in menu settings.

● The power button is for power and back in the menu settings, pause, and start recording

in recording mode

Turning the device on and off :

● With the watch on your left wrist, the power button is located at the bottom right on the

side

● Hold down for 3 seconds to turn it on. A welcome screen will appear and bring you to the

recordings section

● Hold down for another 3 seconds to turn the device off. A “Bye” will appear and turn off

How to playback and delete files off the device using headphones :

● Connect the headphones to the USB port on the device or connect a Bluetooth-enabled

device

● Navigate the menu with the "Up" and "Down" buttons

● Select the "Recordings" menu option by taping the menu button "M"

● Highlight the "Recordings List" and tap the menu button "M"

● Navigate the menu with the "Up" and "Down" buttons to highlight a recording

● Tap the menu button "M" to playback the recorded file

● Fast forward and rewind the recording by holding the "Up" and "Down" buttons

● Change the volume and delete the recordings or adjust the playback type by taping the

menu button "M" to access the playback menu

● Tap the on and off buttons to return to the previous screen. Press and hold the on and off

buttons when done

How to pair the Bluetooth for playback:

● Using Bluetooth headphones or a vehicle Bluetooth: Turn on your Bluetooth device and

enable pairing

● Be sure to turn off Bluetooth connectivity of anything else that usually auto-connects to

your Bluetooth devices

● From the "Main Menu," navigate to the "Set" menu option and tap the menu button "M"

● Highlight Bluetooth on and off and tap the menu button "M"

● Highlight Bluetooth on and tap the menu button "M." The screen will display for a

moment

● Highlight "Search for Device" and tap the menu button "M"

● Navigate to whichever Bluetooth device you want to use by tapping the up and down

arrows and pressing the menu button "M" to select which Bluetooth device to pair with

● Use the on and off buttons to back out of this section until you get back to the main

● You will now be able to navigate to your recordings sections and playback the files

How to set the time and date stamp:

● Navigate to the set menu

● Highlight the date and time and tap the menu button "M"

● Set date = Adjust the time using the "Up" and "Down" arrows

● Set time = Adjust the date using the "Up" and "Down" arrows

Note: Changing this setting changes the time and date displayed on the watch, and

stamp the recordings with the date and time as well.

How to change the clock display timeout settings:

● Navigate to the set menu

● Highlight the "Display Settings" and tap the menu button "M"

● Backlight timer = Adjust how long the time the menu or recording menu displays

● Screensaver hours = How long the watch time is displayed on the watch

Note: Changing this setting will change how long the watches clock is visible on the

watch.

How to manage and delete files from the device:

● Make sure the recorder is turned off and plug in the headphone, then turn on or have the

recorder turned on and paired with a Bluetooth source

● Navigate to "Recordings" within the main menu

● The second option is the "Recordings List." Click the "M" button to enter

● Click the menu "M" on the recording you wish to delete. The file will start to play

● Click the menu "M" to get to the "Playback Menu," where you can adjust the volume,

delete this recording, delete all recordings, and set the playback mode

● Navigate to "Delete" or "Delete All," depending on what you want to do. Press the menu

button "M" to confirm your selection

How to set up password protection:

● Navigate to the "Set" menu and tap the menu button "M"

● Using the up and down arrows, select "Password Setting" with the menu button "M"

● Using the up and down arrow button, you can change the numbers from 1-9

● To move to the following number, hold either the "Up" or "Down" arrow button for two

seconds

● Once finished, tap the menu button "M" to save the password

● The device will now require a password to turn on or connect to a computer

● To turn the password off, navigate back to the "Password Setting" and change the

password back to the default 0000

Note: If the password is forgotten you can use 1028 to unlock the device.

Menu map explained:

● Recordings:

○ Start Voice Recording: Records audio

○ Recordings List: Location of all audio recordings for playback. Volume adjust,

delete, delete all

○ Playback mode: Repeat off, repeat all, single play, repeat 1, backcycling,

backcycling all

○ Record Settings:

■ Recording Quality: 1536kbps - 32kbps quality

■ Recording Sensitivity: High, medium, low mic sensitivity

■ Auto Record

● Record on/off: Turn schedule record on or off

● Auto record cycle: Schedule record once or daily

● Start time: Time schedule record begins

● End time: Time schedule record ends

■ AVR Set

● AVR switch: Voice activation on or off

● AVR level: Change the grade level of activation sensitivity

● AVR delay: Change the delay for recording

■ VOS Mode

● 1-5 Level: 1 is most sensitive, 5 is the least sensitive

● Set

○ Bluetooth

■ Bluetooth on/off: Turn on or off bluetooth connectivity

■ Search for device: Locates bluetooth enabled devices to pair to

■ Device list: Finds previously pair to devices

○ The display settings

■ Brightness: Adjust screen brightness

■ Backlight timer: Adjust the time the menu/record screen stays on before

switching to screensaver

■ Screensaver hours: Adjust the time the screensaver stays on before

switching off

■ Screensaver settings: Turn screensaver setting on or off

○ The date and time: Adjust the date and time

○ power off set

■ Save power off: No activity auto turns device off

■ Set the sleep timer: No activity turns off screen

○ Language: Changes language three is English

○ Information: Displays storage information

○ The format device: Completely erases all recordings

○ The factory settings: Completely erases all recordings and settings

○ Password settings: Password lock the device

Note: If the password is forgotten you can use 1028 to unlock the device.

● Music

○ Location of SpyCentre Security recorded message

How to manage and delete files on a Windows computer:

● Connect the device to the PC

● When connected, the PC will recognize the device as a removable disk

● Open the “Record” folder

● Inside will be the “Voice” folder. Double-click to open the folder

● Double-click the file you wish to play

● To delete a file, right-click and select delete from the popup menu

How to manage and delete files on a Mac:

● Connect the device to your Mac computer

● When connected, the Mac will recognize the device as a removable disk

● Open the “Record” folder

● Open the “Voice” folder

● Double-click the file you wish to play

● To delete a file, click and drag the file you wish to delete to the trash bin

● Empty the trash bin with the device still plugged into your computer to delete the file from

the device permanently

Note: If the above step is not completed on a Mac, the recorded files will not be entirely

deleted from the device. You will have a phantom folder containing the deleted files that

can not be seen on Mac that still take up memory space. Empty the “trash bin” to clear

these files, or your recorder may run out of room.

How to Playback files on a Google Chromebook:

● Connect the device to the USB port of the Chromebook

● A pop-up menu may occur; if so, select “View Files”

● If a pop-up does not occur, select the “O” icon called the “App Launcher“ similar to a

Windows icon button located in the bottom left corner of the screen

● Underneath the “Google Drive” are “My Drive,” “Downloads,” “New Services,” and

something else that may be named “Removable Drive”

● Select the “Removable Drive.” If unsure of this step. Disconnect the device from the

Chromebook and see what is no longer available under Google Drive from step 4

● After selecting the “Removable Drive,” you can now navigate the folders in the main

folder to find the recorded files

● Double click to play

How to playback files on an Android smartphone or tablet (No Apple Products):

● An OTG cable is required for this process. For all other steps, refer to the OTG cable

guide at https://spycentre.com/products/dual-android-otg-cable , scroll to the bottom of

the page and click on user guides

● Go to your “Device Storage,” and look for external memory. Inside will be all the files you

can click on to review what was captured

● For all other steps, refer to the OTG cable guide on spycentre.com

Note: To playback the files on these devices, you may need to download a media

player that can play in WAV format. We recommend VLC Media Player.

VLC Media Player (Recommended for optimal usage)

How to download VLC Media Player on a Mac computer

● Go to www.videolan.org and click the “Download VLC”

● It will open a new window and begin downloading

● If it does not automatically start downloading, press the “Click Here” and select one of

the mirrored sites

● Once completed, a new file named VLC will be visible on the desktop

● Open the folder, and in the folder, move the VLC to the “Applications Folder” by dragging

and dropping it

● Once in the “Application Folder,” the VLC player will complete the installation

● Open VLC Media Player in the “Applications Folder” and drag your video files to the

“Drag Here” dialog box to open and play

● If the VLC player is not installed, a change to the security and privacy settings is needed

● To access your security and privacy, click on the Apple icon on the taskbar and select

“System Preferences”

● Select “Security and Privacy”

● Make sure the lock icon on the bottom of the screen is open and set to “Make Changes”

● Select the button “Open Anyway”

● VLC will now be fully installed

How to download and use VLC Media Player on a Windows computer

● Go to www.videolan.org and click the “Download VLC”

● It will open a new window and begin downloading

● If it does not automatically begin downloading, press the “Click Here” and select one of

the mirrored sites

● Once downloading has been completed, select run and install

● Once finished, a VLC icon will now be available on your PC

● To default, open a file in VLC Media Player, right-click on the file you wish to open and

select “Open With,” and choose VLC

● To change all files to default, open with VLC Media Player: Right-click and choose

“Properties,” then click on the “Change” button next to “Open With” and change it to

VLC, then press ok. Now the files will default open with VLC

Note: If the memory folder of the recorder does not automatically open when connected

to a PC, disconnect the device and perform the following.

1. Type “Control Panel” in the search bar and select “Programs”

2. Under “Default Programs,” click “Change Default Settings for Media or Devices”

3. Under “Removable Devices,” select “Open Folder” to view files

4. Save and reconnect the device to the computer

The Spy Gear Superstore® Since 1993

Spycentre Security 6762 Quick start guide

Brand: Spycentre Security

Model: 6762

Category: Watches

Type: Quick start guide

Download PDF

report

Spycentre Security 6762 Quick start guide

Spycentre Security 6762 Quick start guide

Related papers

Other documents