TomTom Go User manual

TomTom GO

What’s in the box1.

2

What’s in the box

aTomTom GO AOn/Off button

BMicrophone

CLight sensor

DSpeaker

EMemory card (micro SD card)

slot

bWindshield Mount

cAdhesive disk for Windshield

Mount

dUSB car charger

eHome Dock fDocumentation pack

A

B

C

D

E

Before you start2.

3

Before you start

Switching on and off

Install your TomTom GO navigation device in your car following the

instructions in the installation section at the start of this book.

To switch on your navigation device, press and hold the On/Off button until

you see the start-up screen. The first time you switch on your device, it may

take a short time to start.

To set up your device you need to answer a few questions by tapping the

screen.

Device not starting

In rare cases, your TomTom GO navigation device may not start correctly or

may stop responding to your taps.

First, check that the battery is properly charged. To charge the battery,

connect your device to the car charger. It can take up to 2 hours to fully charge

the battery.

If this does not solve the problem, you can reset the device. To do this, press

and hold the On/Off button for fifteen seconds and release the button when

your device begins to restart.

Battery notes

The battery in your TomTom GO navigation device charges when you connect

it to the car charger or to your computer.

The light next to the On/Off button is orange while the battery is charging and

is green when the battery is fully charged.

When you connect your device to a computer, you are asked if you want to

connect to the computer. If you select No and then do not tap the screen

within three minutes, the device will automatically switch off. This happens so

that the battery can charge faster.

Note: You should plug the USB connector directly into a USB port on your

computer and not into a USB hub or USB port on a keyboard or monitor.

Windshield Mount

Use the Windshield Mount to install your TomTom GO inside your car.

Make sure that both the Windshield Mount and your windshield are clean and

dry before you attach the mount. Place the Windshield Mount so that it does

not interfere with your view of the road or of any of the controls in your car.

4

To attach the Windshield Mount, press the suction cup firmly against the

windshield on an area where the glass is flat. Then twist the rubber grip near

the base of the Windshield Mount in a clockwise direction until you hear a

click.

Home Dock

The home dock is used for charging your TomTom GO when it is not in the car

and for connecting your GO to your computer.

When connected to your computer, you can use TomTom HOME to manage

your GO.

GPS reception

When you first start your TomTom GO navigation device, the device may

need a few minutes to determine your GPS position and show your current

position on the map. In future, your position will be found much faster, usually

within a few seconds.

To ensure reception of a strong GPS signal, you should use your device

outdoors. Large objects such as tall buildings can sometimes interfere with

reception.

Important: Some vehicles have heat reflective shielding in the windshield

which may prevent your navigation device from locating your position.

The TomTom External Antenna Kit (available for purchase as an accessory)

can help to improve reception.

Safety Notice

Your TomTom GO contains a GSM/GPRS module which can interfere with

electrical devices such as cardiac pacemakers, hearing aids and aviation

equipment.

Interference with these devices may endanger the health or life of others.

Do not use near unprotected electrical units nor in areas where the use of

mobile telephones is prohibited, such as hospitals and airplanes.

Take care of your device

Never leave your TomTom GO navigation device or accessories on view when

you leave the car or they may become an easy target for thieves.

It is important to take care of your device.

• Your device is not designed for use in extreme temperatures and any such

exposure may cause permanent damage.

• Do not open the casing of your device under any circumstances. Doing so

may be dangerous and will invalidate the warranty.

• Wipe or dry the screen of your device using a soft cloth. Do not use any

liquid cleaners.

Safety3.

5

Safety

Choosing where to attach the Windshield Mount

Consider carefully where you place the Windshield Mount in your car. The

Windshield Mount should not block or interfere in any way with the following:

• Your view of the road

• Any of the controls in your car

• Any of your mirrors

• The airbag

You should be able to reach your GO easily when it is in the Windshield Mount

without leaning or stretching. The diagrams show where you can safely attach

the Windshield Mount.

You can attach the Windshield Mount to the windshield, side window or use a

Dashboard Mount Disk to attach the Windshield Mount to your dashboard.

TomTom also offers alternative mounting solutions for your TomTom device.

For more information about Dashboard Mount Disks and alternative mounting

solutions, go to www.tomtom.com/accessories.

Installing the Windshield Mount

Make sure that both the Windshield Mount and your window are clean and

dry.

1. Press the suction cup firmly against the window on an area where the glass

is flat.

2. Twist the rubber grip near the base of the Windshield Mount in a clockwise

direction until you hear a click.

The Windschield Mount is now installed.

6

Safety preferences

We recommend using the safety preferences to make your driving as safe as

possible. The safety preferences include, for example, the following options:

• Hide most menu options when driving

• Show safety reminders

• Warn when driving faster than allowed

You can also drive more safely by using voice commands to control your

TomTom GO.

Making your first journey4.

7

Making your first journey

Planning a route with your TomTom GO navigation device is easy. To plan a

route, follow the steps below.

Important: For safety reasons, you should always plan a route before you

start your journey.

1. Tap the screen to bring up the Main Menu.

Note: The buttons on your navigation device are shown in full color unless a

button is currently unavailable. For example, the button named Find

alternative in the Main Menu is not available until you have planned a route.

2. Tap Navigate to...

3. Tap Address.

When you enter an address, you can choose from the following options:

• City center - tap this button to set your destination as the center of a city

or town.

• Street and house number - tap this button to set an exact address as your

destination.

• Zip code - tap this button to enter a zip code as your destination.

Note: You can enter a zip code for any country. In the UK and the Netherlands,

ZIP codes are detailed enough to identify a house on their own. In other

countries you can enter a zip code to identify a town or area. You will then

have to enter a street and house number.

8

• Cross street or intersection - tap this button to set your destination as the

point where two streets meet.

• Spoken address - tap this button to set your destination by saying the

address to your navigation device.

In this example, we will enter an exact address.

4. Tap Street and house number.

Note: When planning a trip for the first time your navigation device asks you

to choose a state or country. Your choice is saved and used for all routes you

plan.

You can change this setting at any time by tapping the flag.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are

shown. When your destination appears in the list, tap the name of the town

to set the destination.

Tip: Instead of typing the name, tap this button to say the address by

speaking to your navigation device.

6. Start to type the street name and tap on the street when it appears in the list.

As with the name of the town, the names of the streets that match what you

have typed are shown. When your destination appears in the list, tap the

name of the street to set the destination.

7. Enter the house number and then tap Done.

9

8. Your navigation device asks if you need to arrive at a particular time. For this

exercise, tap NO.

The route is calculated by your device using IQ Routes

TM

.

IQ Routes is used to plan the best possible route taking into account the real

average speeds measured on the roads.

9. When the route has been calculated, tap Done.

Your TomTom GO navigation device will warn you about any traffic delays

and immediately begin to guide you to your destination, using both spoken

instructions and on-screen directions.

Arrival times

When you plan a route, your TomTom GO asks you if you need to arrive at a

particular time.

Tap YES to enter a preferred arrival time.

Your GO calculates your arrival time and shows you whether you will arrive

on time.

You can also use this information to work out when you need to leave. If your

GO shows that you will arrive 30 minutes early, you can wait and leave in 30

minutes time, rather than arrive early.

Your arrival time is constantly recalculated during your trip. The status bar

shows whether you will arrive on time or if you are going to be late, as shown

below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before

the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the

time you entered, it is shown in yellow.

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered,

it is shown in red.

Status bar

preferences

Tap Status bar preferences in the Preferences menu, to enable or disable

arrival time notifications.

Select the required options on the first menu screen and then tap Done.

To enable arrival time notifications, select Show leeway to arrival time.

10

Other navigation options

When you tap Navigate to..., you can set your destination in many ways, not

just by entering the address. The other options are listed below:

Local search

Tap this button to use TomTom Local Search with Google search to help

you find shops and businesses in and around your current location.

You can choose to search for stores and businesses near you, near your

destination, near any other destination or in a city.

For example, if you are looking for a swimming pool near your current

location, enter ’swimming pool’ and choose the best search result.

Home

Tap this button to navigate to your Home location.

You will probably use this button more than any other.

Favorite

Tap this button to select a Favorite as your destination.

Address

Tap this button to enter an address as your destination.

Recent

destination

Tap this button to select your destination from a list of places you have

recently used as destinations.

Point of

Interest

Tap this button to navigate to a Point of Interest (POI).

Point on map

Tap this button to select a point on the map as your destination using the

map browser.

Latitude

Longitude

Tap this button to enter a destination using latitude and longitude values.

TomTom

Buddy

Tap this button to navigate to the last known position of a TomTom Buddy.

Don’t forget that the Buddy may move before you reach him.

11

Planning a route in advance

You can use your GO to plan a route in advance, selecting your starting point

and your destination.

Here are some more reasons to plan a route in advance:

• Find out how long a trip is going to take before you start.

You can also compare trip times for the same route at different times of the

day or on different days of the week. Your TomTom GO uses IQ Routes

when planning a route. IQ Routes calculates routes based on the real

average speeds measured on roads.

• Study the route of a trip you are planning.

• Check a route for someone who is coming to visit you and then explain the

route to them in detail.

To plan a route in advance, follow these steps:

1. Tap the screen to bring up the main menu.

2. Tap the arrow button to move to the next menu screen and tap Prepare

route.

3. Select the starting point for your trip in the same way that you would select

your destination.

4. Set the destination for your trip.

5. Choose the type of route that should be planned.

• Fastest route - the route which takes the least time.

• Shortest route - the shortest distance between the locations you set. This

may not be the quickest route, especially if the shortest route is through

a town or city.

• Avoid freeways - a route which avoids freeways.

• Walking route - a route designed for making the trip on foot.

• Bicycle route - a route designed for making the trip on a bicycle.

• Limited speed - a route for a vehicle which can only be driven at a limited

speed. You have to specify the maximum speed.

6. Choose when you will make the trip you are planning. There are three

options:

• Now

• Specific date and time - you will be asked to enter the date and time.

• No specific date and time

If you select either Now or Specific date and time, your GO uses IQ Routes

to work out the best possible route at that time, using the real average

speeds measured on roads. In this way you can compare how long a trip

takes at different times of day, or on different days of the week.

Position of

last stop

Tap this button to select your last recorded position, as your destination.

Prepare route

12

7. Your TomTom GO plans the route between the two locations you selected.

More information about a route

You can access these options for the route you last planned by tapping View

route in the Main Menu or the Details button on the route summary screen.

You can then select from the following options:

Browse as

text

Tap this button for a list of all the turn instructions on the route.

This is very useful if you need to explain a route to someone else.

Browse as

images

Tap this button to see each turn in the trip. Tap the right and left arrows to

move forwards and backwards through the trip.

Tap the screen to turn off the 3D display and view the map from above.

Browse map

of route

Tap this button to see an overview of the route using the map browser.

Show route

demo

Tap this button to watch a demo of the trip. You can interrupt the demo at

any time by tapping the screen.

Show route

summary

Tap this button to open the route summary screen.

View route

Tap this button to see your route.

Voice recognition5.

13

Voice recognition

Instead of tapping the screen to control your TomTom GO, you can now give

instructions to your GO using your voice.

For example, to increase the volume on your GO, you can say, "Increase

volume."

Important: To use voice recognition, you must have a computer voice

installed on your TomTom GO. If you don’t have a computer voice installed,

use TomTom HOME to install one.

To view the list of available commands, tap Voice Control preferences in the

Preferences menu and then tap What can I say?

You can also look at the voice recognition reference card in your box.

Using voice recognition

Note: You must select a computer voice in order to use voice recognition. To

select a computer voice, tap Change preferences in the Main menu. Then tap

Voice preferences and Change voice. Select a computer voice.

In this example, you will use voice recognition to plan a journey to your Home

address.

1. Tap the voice recognition button in the Driving View.

Note: To add or remove this button from the Driving View, tap Voice control

preferences in the Preferences menu and then tap Enable voice control or

Disable voice control.

The voice recognition monitor is shown in color, unless voice recognition is

busy with another task.

2. When you hear a beep, say, "Navigate to Home."

When you speak, the voice recognition monitor shows if you are talking too

loudly or quietly:

A green bar means your voice is at the right level for your GO

to hear your commands.

14

A red bar means your voice is too loud.

A grey bar means your voice is too quiet.

For some phrases, your GO will always repeat the command and then ask

you if the command has been correctly recognized.

3. If the command is correct, say, "Yes."

If the command is incorrect, say, "No" and when prompted, say the

command again after the beep .

Your GO plans a route from your current position to your Home address.

Tips

• Voice recognition switches off after a few seconds if you don’t say anything.

For example, if your GO asks you to confirm the last command you gave

and you don’t say anything, voice recognition switches off after a few

seconds.

• You can stop your GO from listening for commands either by tapping the

screen or by saying any of the following commands: Back, Cancel, Quit.

• To select an item from a list, tap the screen to select the item. Voice

recognition cannot be used to select items from a list.

Planning a trip using your voice

Important: You should always plan your journey before you start driving. It is

dangerous to plan a route while driving.

To plan a route to an address using speech, do the following:

1. Tap the voice recognition button in the Driving View.

2. When you hear a beep, say, "Navigate to address."

When you speak, the voice recognition monitor shows if you are

talking too loudly or quietly:

A green bar means your voice is at the right level for your GO

to hear your commands.

A red bar means your voice is too loud.

A grey bar means your voice is too quiet.

For some phrases, your GO will always repeat the command and then ask

you if the command has been correctly recognized.

15

You can now enter an address using speech.

Alternatively, you can tap the screen to start planning a trip, then tap

Spoken address (dialog) or Spoken address to start entering an address by

voice.

3. Say the city name.

When you say the city name, you are then shown a list of six names that

match what you said.

Your GO tells you the name at the top of the list. If the name you hear is

correct, then say, "Done" or "OK" or "Yes" or "One" or tap on the name.

If the city name you hear is not correct, but the name appears in the list, then

say the number next to the correct name or tap on the correct name.

For example, if the correct name is Rotterdam and this name is number two

in the list, you could say, "Two" or tap on the name, Rotterdam.

If the city name is not shown in the list, then say "Back" or "No" or tap the

Back button to return to the previous screen. Then say the city name again.

Note: You need to say numbers in the same language that is used for menu

buttons.

4. Say the street name.

Your GO states the name shown at the top of the list. If the name you hear

is correct, then say, "Done" or "OK" or "Yes" or "One" or tap on the name.

Note: Different locations may have similar names, such as a road that has

multiple zip code locations. In such cases, all of these locations are shown in

the list and you need to look at the screen and select the correct location.

If the name you hear is incorrect but the correct name is shown in the list,

then say the number next to the correct name or tap on the street name.

If the street name is not shown in the list, say "Back" or "No" or tap the Back

button to return to the previous screen. Then say the street name again.

5. Say the house number.

16

Numbers should be pronounced normally. For example, you would say the

number 357 as one continuous sentence, "Three hundred and fifty seven."

If the number is shown incorrectly, say, "Back" or "No" or tap the Backspace

key. Then say the number again.

Tip: If you say, "Back" when there are no numbers shown on the screen, then

your GO will return you to the previous screen.

When the number is shown correctly say, "Done" or "OK." Alternatively,

enter the number by tapping the screen.

To select a crossroads as the location, say "Crossing".

Note: You need to say numbers in the same language that is used for menu

buttons.

6. Your GO asks if you need to arrive at a particular time. For this exercise, tap

NO.

The route is calculated by your GO.

7. When the route has been calculated, tap Done.

Voice address input

Important: You should always plan your journey before you start driving. It is

dangerous to plan a route while driving.

If you don’t use voice recognition to start planning a journey, you can still

enter an address using speech.

To start planning a trip, tap Navigate to... in the Main Menu, then tap Address.

To enter your destination using your voice, tap one of these buttons:

Spoken

address

(dialog)

Tap this button to enter an address using only speech. Using this option,

your GO can recognize the following:

• Commands: Yes, No, Back, Done, OK, Crossing.

• Street names.

•Place names.

• Numbers: Numbers should be pronounced as individual numerals. For

example, to say the number 35, say "Three" and then say "Five."

Using Spoken address (dialog), you can enter information without tapping

the screen.

Spoken

address

Tap this button to enter an address using both speech and by tapping the

screen. Using this option your GO can recognize the following:

• Street names.

•Place names.

Using Spoken address is typically faster than using Spoken address

(dialog).

17

Your GO recognizes place and street names spoken using the local language

and pronunciation.

It is not possible to use voice address input to say place and street names in

all countries.

You can use speech to enter destinations wherever you see this button.

You can use speech to enter these types of destination:

• City center - to say the center of a city or town, tap the speech button at

the bottom of the keyboard.

• Street and house number - to say an address, tap the speech button at

the bottom of the keyboard.

• Crossing or intersection - to say the point where two streets meet, tap

the speech button at the bottom of the keyboard.

When this button is shown in gray, you cannot use speech to enter an

address.

Note: Zip code address entry is not possible using speech.

Driving View6.

18

Driving View

When your TomTom GO starts, you are shown the Driving View along with

detailed information about your current location.

Tap the center of the screen at any time to open the Main Menu.

Note: The Driving View is shown in black and white until your GO locates your

current position.

ATap + and - to zoom in and out.

BQuick menu - swich this on in the Preferences menu.

CYour current position.

DThe name of the next major road or road sign information, if applicable.

The name of the next major road, road sign information, if applicable, or the

next street name, if enabled.

ETraffic sidebar.

FVoice recognition button.

GNavigation instruction for the road ahead.

Tap this area to repeat the last spoken instruction and to change the

volume.

HThe name of the street you are on.

IInformation about your trip such as trip time, remaining distance and arrival

time.

To change the information shown, tap Status bar preferences in the

Preferences menu.

JGPS signal strength.

Advanced Lane Guidance7.

19

Advanced Lane Guidance

Your TomTom GO helps you prepare for highway exits and intersections by

showing you which lane you should be in.

Note: This information is not available for all intersections or in all countries.

For some exits and junctions, an image shows the turn and the lane you

should take.

To turn the images off, tap Hide lane images in the Preferences menu.

For other exits and intersections, your GO shows the lane you should take in

the Status bar. To turn this guidance off, tap Change preferences in the Main

Menu, then tap Status bar preferences. Clear the checkbox for Show lane

guidance.

Finding alternative routes8.

20

Finding alternative routes

Once you have planned a route, you may want to change something about the

route, without changing your destination.

Why change the route?

Maybe for one of these reasons:

• You can see a roadblock or a line of traffic ahead.

• You want to travel via a particular location, to pick someone up, stop for

lunch or fill up with gas.

• You want to avoid a difficult intersection or a road you don’t like.

Find alterna-

tive...

Tap Find alternative... in the Main Menu to change the route that is

currently planned.

The Find alternative... button is also shown in the route summary screen

after you plan a route.

Calculate

alternative

Tap this button to calculate an alternative to the route already planned.

Your GO will look for another route from your current location to your

destination.

If you decide you would prefer to use the original route after all, tap

Recalculate original.

Why would I need to do this?

Apart from the roads near your position and near your destination, the new

route will use totally different roads to reach your destination. This is an

easy way of calculating a totally different route.

Avoid

roadblock

Tap this button if you can see a roadblock or a line of traffic ahead. You then

have to choose how much of the route ahead you want to avoid.

Choose from the different options: 100m, 500m, 2000m, 5000m. Your GO

will recalculate your route avoiding the section of the route for the distance

you selected.

Don’t forget that once a new route is calculated, you may have to turn off

the road you are on very soon.

If the roadblock suddenly clears, tap Recalculate original to return to your

original route.

Page is loading ...

TomTom Go User manual

TomTom Go User manual

Related papers

Other documents