AP-WX50
AP-WX50
Tilt wall mounting bracket
Installation and Setup Guide
P/NO : 3828VA0495C
Hole Drilling Template
Guide Sticker
4-Product Bracket Bolts
4-Product Bracket Bolts
4-Guide Spacer
10-Bolts for tilt wall mounting bracket 10-Wall Anchor Bolt Sleeves
Installation and Setup Guide
Accessories
4-Product Bracket Bolts
(M8X35)
2-Safety locking Bolts
7-Bolts for tilt wall mounting
bracket
After reading this manual, keep it in the place that the user always can contact easily.
Safety Instructions
Safety Instructions
WARNING
- Qualified service technician should install the product properly after reading this manual thoroughly.
- Qualified service technician should hand this manual over to the customer after installation and ask him/her to
read and keep it.
Do not install this product on the place where it cannot be
supported.
It may cause the product to fall and could
cause injuries.
Contact the qualified service technician
for moving or replacing this
product after installing.
Installing the product needs specified technic,
so it may cause safety problem to move or
install it by yourself.
Do not hang on or impact on this product.
It may cause the product to fall and could
cause injuries.
Do not install this product by yourself. Contact
the service technician qualified by
the manufacturer.
It may cause injuries.
KOREAN / ENGLISH
NOTES
Install this product followed by the instruction of the
manual.
Otherwise it may cause serious injuries or
damage of the product.
Before installing, check whether the
material of wall satisfies the
specifications and make sure to use
enclosed anchors supplied with the
product.
Otherwise it may cause safety problem.
Do not place a heat source
(radiator or heater) or a
humidifier under the installed
product.
It may cause a fire or could give an
electric shock.
Make sure to unplug before installing this product.
Otherwise it may cause a fire or could give an electric shock.
Do not install this product barehanded.
It may cause injuries.
Do not install this product near a
sprinkler, a sensor, a high voltage
electric line, any power source or
the place where impact or vibration
can affect.
When drilling use drill and drill bit
specified by the manufacturer.
And the depth of the hole should
satisfy the specifications.
Otherwise it may cause safety problem.
Do not install this product by yourself. Get some help
from others.
It may cause the product to fall and could cause injuries.
Installation
Installation
Bracket
Push the product brackets in the direction shown by arrow 1, then detach the product brackets from the wall
mounting bracket.
1
Product Bracket
upper
lower
KOREAN / ENGLISH
2
Check the product size. Connect to inch indicated on the bracket for inch adjustment.
Fixate 4 bolts (M4x6) on the width adjustment bracket and angle bracket for wall.
Bolt integrated spot/in the blank (Number of the bolt to be used)
VESA Non-corresponding model
VESA Non-corresponding model
VESA Non-corresponding model
/The installation standard for the model
after the year 2005)
Corresponding model
Size adjustment bracket 1
Size adjustment bracket 2
Tilt wall mounting bracket
3
How to assemble the Guide spacer
Guide Spacer
M5 x35: Plasma/LCD VESA ,
* M6 x35: Plasma/LCD VESA
,
M8 x35: Plasma/LCD 55 (139cm) (50kg )V ESA
Bracket Bolts
M5 x35: Plasma/LCD VESA Non-corresponding model application,
* M6 x35: Plasma/LCD VESA Corresponding model application, M8 x35:
Plasma/LCD 55
inch (50kg
VESA Corresponding(Non-corresponding) model application
As shown above, carefully place the Display screen side down on a cushioned surface that will protect the product and
screen from damage.
If bolts are screwed on the wall mount, remove the bolts first to fasten the wall mount.
M5 x35, M6 x35, M8 x35)
Product Bracket Bolts
M5 x35, M6 x35, M8 x35)
Bracket Hook
Connect the guide spacer to the bracket. Pull the bracket with guide spacer connected in the arrow direction to assemble it.
Fixate the bracket and set with bolt.
Insert the guide spacer in the horizontal direction (with ‘TOP’ letter on left) to the
bracket.
Rotate the guide spacer so that ‘TOP’ letters are shown to the top. There should
not be any movement of guide spacer after connecting. If the length of the bolt
doesn’t match, please refer to SVC Guide.
KOREAN / ENGLISH
5
- Using the hole-drilling template provided, mark the positions of the anchor holes shown on the drawing in the wall;
using a center-punch or other device to clearly identify the 10 drill hole positions.
Note: It is advisable to use a bubble level to make sure that the template is horizontally true.
- Warning: The surface that the tilt wall mounting bracket is to be mounted on should be of sufficient strength to support
the weight of the monitor and speakers typically; concrete, strong/weak natural rock, brick and hollow block.
- Warning: Plasterboard is not a sufficiently strong enough material; unless the bolts are anchored into standard
construction type studs capable of supporting the weight of the monitor and speakers. If you can not determine the
strength of the material, each drilled hole should be capable of supporting normal stress 686kgf/m
2
(70N) and shear
stress 980kgf/m
2
(100N).
In the proportion of horizontal, fix drawing of the accessories on the wall.
Mark position of anchors bolts on he wall.
horizontal
vertical
Keep these instructions for future reference
Keep these instructions for future reference
37LZ3-
,
42LZ3-
, VESA(
600)-
,
42P-
,
50P-
,
60P-
, VESA(
800)-
Bolt the tilt wall mounting bracket to indicated number of a
drawing.
37LZ3-
,
42LZ3-
, VESA(
600)-
,
42P-
,
50P-
,
60P-
, VESA(
800)-
If it’s impossible to bolt in indicated position, bolt it the
closest position. Don’t change the indicated position
more 2 position.
When you install, vertically, insert the bolts in the
proportion of vertical.
a. Using an 8mm drill appropriate for the material on the wall, drill
each hole to a depth of 80mm – 100mm.
b. Clean each drilled hole.
c. Insert an anchor supplied with the tilt wall mounting bracket into
each hole.
d. Mount the tilt wall mounting bracket on the wall using the 12
washers and bolts supplied.
e. Adjust the bolt head angles as necessary, see above.
How to fix anchors and bolts
How to fix bracket
Anchor
Bolts for tilt wall mounting bracket
6
KOREAN / ENGLISH
7
Carefully lift up the product and place it in position on the tilt wall mounting bracket securely as shown by arrow 1.
Push the bottom of the product toward he wall as shown in arrow 2, so that the product will “click” into position onto the
tilt wall mounting bracket.
Assemble the tilt wall mounting bracket with the product bracket using the Safety locking bolt (M4x6) bolts (See 3).
Pull the bottom of the set to check the connected condition on whether the monitor is firmly fixed.
See A above,be sure to lift a product/speakers assembly by the product only, do not lift using only the speakers.
Attach the guide sticker around the product. When separating the wall mounting bracket from the product, refer to the guide sticker.
If the product leans to one side, loose the bolt 3. Then, adjust the tilt with bolt 4 (M4x12) and tighten the bolt 3. The
product tilt is changed according to bolt rotation direction.
When you match product after adjusting tilt angle, refer to figure and explanation below. (Note: Tilt angle can be adjusted after installation and setup.)
You cannot adjust the tilt angle after installation, vertically.
Do not place the hands in the product back side or wall mount. It may cause injury.
Two adult people who are capable of adjusting the tilt angle to need excessive force.
When adjusting the number angle of the product, you must use both hands and then you can adjust the angle as shown above.
When adjusting the number angle of the product, you must use both hands and then you can adjust the angle as shown above.
When adjusting the number angle of the product, first you adjusting the number angle and then adjusting the number angle of
the monitor.
When adjusting the number angle of the product, you must use both hands and then you can adjust the angle as shown above.
When adjusting the number angle of the product, you must use both hands and then you can adjust the angle as shown above.
As size of the product, it may change the tilt angle adjustment. (Upper picture explains the features available on the 42inch Plasma.)
9
Tilt Angle Adjustment
KOREAN / ENGLISH
Width
Height
Depth
Weight
V
Wall mount Vesa
specification
Standard size for the installation of a wall-hanging TV
Specifications
Specifications
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
V7 V7-C5E-25-BLU-S Datasheet
-
V7 C5x Datasheet
-
Samsung WA1350S User manual
-
Electrolux EWF549 User manual
-
Electrolux EMS2388 User manual
-
-
RCA Pro845 User manual
-
Panasonic SJ-MR220 User manual
-
-
American Dynamics Excalibur 168 Operating Instructions Manual
