Supermicro A+ Server 1040C-T, Beige User manual

AS 1040C-T

AS 1040C-8

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates.

The manufacturer reserves the right to make changes to the product described in this manual at

any time and without notice. This product, including software, if any, and documentation may not,

in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or

machine without prior written consent.

IN NO EVENT WILL THE MANUFACTURER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING

THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING

SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. The manufacturer's total liability for

all claims will not exceed the price paid for the hardware product.

Unless you request and receive written permission from the manufacturer, you may not copy any

part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

Manual Revision 1.0

Release Date: September 28, 2006

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the AS1040C-T/1040C-T/1040C-

8. Installation and maintainance should be performed by experienced technicians

only.

The 1040C-T/1040C-8 is a high-end 1U rackmount server based on the

SC818TQ+1000/SC818S+-1000 server chassis and the H8QCE+/H8QC8+

serverboard, which supports four AMD Opteron™ 800 series processors and up

to 32 GB of ECC registered DDR400/333 or 64 GB of ECC registered DDR266

SDRAM memory.

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with

the server system and describes the main features of the H8QCE+/H8QC8+

serverboard and the SC818TQ+1000/SC818S+-1000 chassis, which make up the

1040C-T/1040C-8.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the 1040C-T/1040C-8 into a

rack and check out the server conﬁ guration prior to powering up the system. If your

server was ordered without processor and memory components, this chapter will

refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

iii

Preface

iv

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

1040C-T/1040C-8.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the H8QCE+/H8QC8+ serverboard,

including the locations and functions of connectors, headers and jumpers. Refer

to this chapter when adding or removing processors or main memory and when

reconﬁ guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC818TQ+1000/SC818S+-1000

1U rackmount server chassis. You should follow the procedures given in this chapter

when installing, removing or reconﬁ guring SATA/SCSI or peripheral drives and when

replacing the system power supply unit and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: BIOS POST Codes

Appendix C: System Speciﬁ cations

AS1040C-T/1040C-8 User's Manual

v

Preface

Notes

vi

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1-3

Chapter 2: Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System ................................................................................... 2-1

2-3 Preparing for Setup ........................................................................................ 2-1

Choosing a Setup Location ...................................................................... 2-2

Rack Precautions ..................................................................................... 2-2

Server Precautions ................................................................................... 2-2

Rack Mounting Considerations ................................................................ 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rails ........................................................ 2-4

Installing the Inner Rails .......................................................................... 2-4

Installing the Outer Rails .......................................................................... 2-5

Installing the Server into the Rack ........................................................... 2-6

2-5 Checking the Serverboard Setup ................................................................... 2-7

2-6 Checking the Drive Bay Setup ....................................................................... 2-9

Chapter 3: System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons .................................................................................... 3-1

Reset ........................................................................................................ 3-1

Power ....................................................................................................... 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Overheat/Fan Fail .................................................................................... 3-2

NIC2 ......................................................................................................... 3-2

NIC1 ......................................................................................................... 3-2

HDD .......................................................................................................... 3-3

Power ....................................................................................................... 3-3

3-4 Drive Carrier LEDs ......................................................................................... 3-3

AS1040C-T/1040C-8 User's Manual

Chapter 4: System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ........................................................................... 4-2

4-3 ESD Precautions ............................................................................................ 4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the Serverboard .............................................................................. 5-1

5-2 Mounting the Serverboard into a Chassis ...................................................... 5-2

5-3 Processor and Heatsink Installation ............................................................... 5-3

5-4 Connecting Cables ......................................................................................... 5-6

Connecting Data Cables .......................................................................... 5-6

Connecting Power Cables ....................................................................... 5-6

Connecting the Control Panel .................................................................. 5-6

5-5 I/O Ports ......................................................................................................... 5-7

5-6 Installing Memory ........................................................................................... 5-8

5-7 Adding PCI Cards ........................................................................................... 5-9

5-8 Serverboard Details ...................................................................................... 5-10

H8QC8+/H8QCE+ Layout ...................................................................... 5-10

H8QC8+/H8QCE+ Quick Reference ...................................................... 5-11

5-9 Connector Deﬁ nitions ................................................................................... 5-12

ATX Power Connector ........................................................................... 5-12

Auxiliary 1 Power Connector ................................................................. 5-12

Auxiliary 2 Power Connector ................................................................. 5-12

Power LED ............................................................................................. 5-12

HDD LED ............................................................................................... 5-13

NIC1 LED ............................................................................................... 5-13

NIC2 LED ............................................................................................... 5-13

Overheat/Fan Fail LED .......................................................................... 5-13

Power Fail LED ...................................................................................... 5-14

Reset Button .......................................................................................... 5-14

Power Button .......................................................................................... 5-14

Universal Serial Bus Ports ..................................................................... 5-14

Extra USB Headers ................................................................................ 5-15

Serial Ports ............................................................................................. 5-15

Fan Headers .......................................................................................... 5-15

JLAN 1/2 (Ethernet Ports) ....................................................................... 5-15

Power LED/Keylock/Speaker ................................................................. 5-16

ATX PS/2 Keyboard & Mouse Ports ...................................................... 5-16

vii

Table of Contents

viii

Chassis Intrusion .................................................................................... 5-16

Wake-On-LAN ........................................................................................ 5-17

Wake-On-Ring ........................................................................................ 5-17

Overheat LED ........................................................................................ 5-17

3rd Power Supply Alarm Reset Header ................................................. 5-17

I

2

C Header for Power Supply ................................................................. 5-18

SMBus Header ....................................................................................... 5-18

Additional Fan Headers ......................................................................... 5-18

Compact Flash Power Headers ............................................................. 5-18

5-10 Jumper Settings ............................................................................................ 5-19

Explanation of Jumpers ......................................................................... 5-19

CMOS Clear ........................................................................................... 5-19

SCSI Controller Enable/Disable ............................................................. 5-20

SCSI Termination Enable/Disable .......................................................... 5-20

3rd Power Supply Fail Signal Enable/Disable ....................................... 5-20

Watch Dog Enable/Disable .................................................................... 5-21

JLAN1/2 Enable/Disable ........................................................................ 5-21

VGA Enable/Disable ............................................................................... 5-21

5-11 Onboard Indicators ....................................................................................... 5-22

JLAN1/JLAN2 LEDs ............................................................................... 5-22

5-12 Floppy, IDE, Parallel Port, SCSI and SATA Drive Connections ................... 5-23

Floppy Connector ................................................................................... 5-23

IDE Connectors ...................................................................................... 5-24

Parallel Port Connector .......................................................................... 5-25

SATA Ports ............................................................................................. 5-25

SCSI Connectors ................................................................................... 5-26

5-13 Enabling SATA RAID .................................................................................... 5-27

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 System Fans ................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

Replacing System Fans ........................................................................... 6-3

6-4 Drive Bay Installation/Removal ...................................................................... 6-4

Accessing the Drive Bays ........................................................................ 6-4

SATA/SCSI Drive Installation ................................................................... 6-5

DVD-ROM and Floppy Drive Installation ................................................. 6-7

6-5 Power Supply ................................................................................................. 6-8

AS1040C-T/1040C-8 User's Manual

Table of Contents

ix

Chapter 7: BIOS

7-1 Introduction ...................................................................................................... 7-1

7-2 Main Menu ....................................................................................................... 7-2

7-3 Advanced Settings Menu ................................................................................ 7-2

7-4 Boot Menu ..................................................................................................... 7-15

7-5 Security Menu ................................................................................................ 7-17

7-6 Exit Menu ....................................................................................................... 7-17

Appendices:

Appendix A: BIOS Error Beep Codes ...................................................................... A-1

Appendix B: BIOS POST Checkpoint Codes .......................................................... B-1

Appendix C: System Speciﬁ cations ........................................................................ C-1

x

Notes

AS1040C-T/1040C-8 User's Manual

Chapter 1

Introduction

1-1 Overview

The AS1040C-T/1040C-8 is a high-end quad processor server that is comprised of

two main subsystems: the SC818TQ+1000/SC818S+-1000 1U server chassis and

the H8QCE+/H8QC8+ serverboard. Please refer to our web site for information on

operating systems that have been certiﬁ ed for use with the 1040C-T/1040C-8.

In addition to the serverboard and chassis, various hardware components have

been included with the 1040C-T/1040C-8:

 One (1) slim DVD-ROM drive [DVM-PNSC-824(B)]

 Six (6) 4-cm counter-rotating chassis fans (FAN-0086)

 Four (4) heatsink retention modules with 8 screws (BKT-0005)

 Four (4) CPU backplates, pre-installed (BKT-0004)

 One (1) 1U chassis air shroud (CSE-PT0128)

 One (1) rackmount kit (CSE-PT51)

 SATA Accessories (1040C-T only)

One (1) SATA backplane (BPN-SAS-818TQ)

One (1) SATA cable (CBL-0044L)

Three (3) SATA drive carriers [CSE-PT39(B)]

 SCSI Accessories (1040C-8 only)

One (1) SCSI backplane (CSE-SCA-818S)

One (1) SCSI cable (CBL-0063)

Three (3) SCA SCSI drive carriers [CSE-PT39(B)]

 Four (4) passive heatsinks for 1U systems (optional, SNK-P0012)

 One (1) CD containing drivers and utilities

Note: (B) indicates the item is available in black.

Chapter 1: Introduction

1-1

1-2

AS1040C-T/1040C-8 User's Manual

1-2 Serverboard Features

At the heart of the 1040C-T/1040C-8 lies the H8QCE+/H8QC8+, a quad proces-

sor serverboard based on the nVidia nForce Pro 2200 (CK804)/AMD8132 chipset.

Below are the main features of the H8QCE+/H8QC8+. (See Figure 1-1 for a block

diagram of the chipset).

Processors

The H8QCE+/H8QC8+ supports four 940-pin AMD Opteron 800 Series 64-bit pro-

cessors. Please refer to the serverboard description pages on our web site for a

complete listing of supported processors (www.supermicro.com/aplus/).

Memory

The H8QCE+/H8QC8+ has sixteen 184-pin DIMM slots (four for each CPU), which

support up to 32 GB of registered ECC DDR400/333 SDRAM or up to 64 GB of

registered ECC DDR266 SDRAM. The memory is an interleaved conﬁ guration,

which requires modules of the same size and speed to be installed in pairs.

Onboard SATA (1040C-T only)

SATA is provided with an on-chip 3 GB/sec SATA controller. The H8QCE+provides

four SATA ports.

Onboard SCSI (1040C-8 only)

Onboard SCSI is provided with an Adaptec AIC-7902W SCSI chip, which supports

dual channel, Ultra320 SCSI at a throughput of 320 MB/sec for each channel. The

H8QCE+ provides two LVD Ultra320 SCSI ports.

Onboard Controllers/Ports

One ﬂ oppy drive controller and one ATA/133/100 controller are provided to sup-

port up to four hard drives or ATAPI devices. The color-coded I/O ports include

one COM port (an additional COM header is located on the serverboard), a VGA

(monitor) port, two USB 2.0 ports, PS/2 mouse and keyboard ports and two G-bit

Ethernet ports.

ATI Graphics Controller

The H8QCE+/H8QC8+ features an integrated ATI video controller based on the

Rage XL graphics chip.

1-3

Chapter 1: Introduction

1-3 Server Chassis Features

The 1040C-T/1040C-8 is a high-end, scaleable server platform. The following is a

general outline of the main features of the SC818TQ+1000/SC818S+-1000 server

chassis.

System Power

The SC818TQ+1000/SC818S+-1000 features a single 1000W power supply. If

it fails, the system will shut down and you will need to replace the power supply

unit. The power supply is a cold-swappable unit that is installed from the front of

the chassis.

SATA Subsystem (1040C-T only)

The SATA subsystem supports up to three 3 Gb/sec SATA hard drives, which are

hot-swappable. The SCSI drives are connected to a SATA backplane. A RAID

controller card can be used with the backplane to provide data security.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the SCSI drives.

SCSI Subsystem (1040C-8 only)

The SCSI subsystem supports up to three 80-pin SCA Ultra320 SCSI hard drives,

which are hot-swappable. Any standard 3.5" drives are supported. SCA = Single

Connection Attachment.) The SCSI drives are connected to a duale channel SCA

backplane with SAF-TE. A RAID controller card can be used with the SCA back-

plane to provide data security.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the SCSI drives.

PCI Expansion Slots

The chassis supports the use of one standard size (full-height, full-length) expansion

card (for PCI-Express x8) with the use of a preinstalled riser card.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-4

AS1040C-T/1040C-8 User's Manual

Front Control Panel

The control panel provides you with system monitoring and control. LEDs indicate

system power, HDD activity, network activity and overheat/fan fail. A main power

button and a system reset button are also included.

I/O Backplane

The I/O backplane on the SC818S+-1000 provides one PCI expansion slot, one

COM port, a VGA port, two USB 2.0 ports, PS/2 mouse and keyboard ports and

two gigabit Ethernet ports.

Cooling System

The SC818S+-1000 chassis has an innovative cooling design that includes six 4-

cm counter-rotating fans located in the middle section of the chassis. The power

supply module also includes a cooling fan. All chassis and power supply fans

operate continuously.

A setting in BIOS (see Chapter 7) is used to control the system fan speed. This

setting uses voltage control to allow fans to run at different speeds. [The recom-

mended setting for the 1040C-T/1040C-8 is "3-pin (Server)".]

1-5

Chapter 1: Introduction

Figure 1-1. nVidia nForce Pro 2200/AMD 8132 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your serverboard. See the previous pages for the

actual speciﬁ cations of your serverboard.

8132

2200

(CK804 )

AMD Opteron

TM

CPU #2

128-bit data + 16-bit ECC

DDR400/333/266

16 x 16 HT link (1 GHz)

Slot #2: PCI-X 100 MHz

Dual SCSI Channels

Gb LAN Ports (2)

SATA Ports (4)

UDMA133

USB Ports (4)

LPC I/O FWH

Kybd/

Mouse

FDD

Parallel

Port

COM

Ports

AMD Opteron

TM

CPU #1

AMD Opteron

TM

CPU #3

AMD Opteron

TM

CPU #4

DIMMs D1-D4

DIMMs A1-A4

DIMMs C1-C4

DIMMs B1-B4

16 x 16 HT link

(1 GHz )

128-bit data + 16-bit ECC

16 x 16 HT link

(1 GHz )

Slot #1: PCI-X 100 MHz

Slot #3: PCI-X 100 MHz

Slot #4: PCI-X 100 MHz

PCI-X CH A

PCI-X CH B

Slot #5: PCI-E x8

Slot #6: PCI-E x8

PCI-E

IPMI

Rage XL

HW

Monitor

Fans

(8)

PCI-32

LPC Bus

1-6

AS1040C-T/1040C-8 User's Manual

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your 1040C-T/1040C-8 up and

running. Following these steps in the order given should enable you to have the

system operational within a minimum amount of time. This quick setup assumes that

your 1040C-T/1040C-8 system has come to you with the processors and memory

preinstalled. If your system is not already fully integrated with a serverboard, pro-

cessors, system memory etc., please turn to the chapter or section noted in each

step for details on installing speciﬁ c components.

2-2 Unpacking the System

You should inspect the box the system was shipped in and note if it was damaged

in any way. If the server itself shows damage you should ﬁ le a damage claim with

the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the 1040C-T/1040C-8.

It should be situated in a clean, dust-free area that is well ventilated. Avoid areas

where heat, electrical noise and electromagnetic ﬁ elds are generated. You will also

need it placed near a grounded power outlet. Read the Rack and Server Precau-

tions in the next section.

2-3 Preparing for Setup

The box the 1040C-T/1040C-8 was shipped in should include two sets of rail assem-

blies, two rail mounting brackets and the mounting screws you will need to install the

system into the rack. Follow the steps in the order given to complete the installation

process in a minimum amount of time. Please read this section in its entirety before

you begin the installation procedure outlined in the sections that follow.

2-2

AS1040C-T/1040C-8 User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack to allow for

sufﬁ cient airﬂ ow and ease in servicing.

- This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets, etc.).

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to the

ﬂ oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack.

• In multiple rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more simul-

taneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack ﬁ rst, and

then work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a

power failure.

• Allow the hot plug SATA/SCSI drives and power supply units to cool before touch-

ing them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

!

Warnings and Precautions!

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tem-

perature of the rack environment may be greater than the ambient temperature

of the room. Therefore, consideration should be given to installing the equip-

ment in an environment compatible with the manufacturer’s maximum rated

ambient temperature (Tmra).

Reduced Airﬂ ow

Equipment should be mounted into a rack so that the amount of airﬂ ow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does

not arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might

have on overcurrent protection and power supply wiring. Appropriate consid-

eration of equipment nameplate ratings should be used when addressing this

concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply con-

nections other than the direct connections to the branch circuit (i.e. the use of

power strips, etc.).

2-4

AS1040C-T/1040C-8 User's Manual

2-4 Installing the System into a Rack

This section provides information on installing the system into a rack unit with the

rack rails provided. If the system has already been mounted into a rack, you can

skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market,

which may mean the assembly procedure will differ slightly. You should also refer

to the installation instructions that came with the rack unit you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies in the rack mounting kit. Each

assembly consists of two sections: an inner ﬁ xed chassis rail that secures directly

to the server chassis and an outer ﬁ xed rack rail that secures directly to the rack

itself (see Figure 2-1). Two pairs of short brackets to be used on the front side of

the outer rails are also included.

Installing the Inner Rails

Both the left and right side inner rails have been pre-attached to the chassis.

Proceed to the next step. A

Figure 2-1. Identifying the Sections of the Rack Rails

(right side rail shown)

Page is loading ...

Supermicro A+ Server 1040C-T, Beige User manual

This manual is also suitable for

Supermicro A+ Server 1040C-T, Beige User manual

Related papers

Other documents