Havis PKG-PSM-276 Installation guide

Havis
Brand
Havis
Model
PKG-PSM-276
Category
Mounting kits
Type
Installation guide
Installation Instructions
ATTACH SUPPORT FOOT TO MAIN BASE USING (2X) 1/4-20 X 3/4"
1.
HEX HEAD CAP SCREWS, LOCK WASHERS AND FLAT WASHERS.
ADJUST SUPPORT FOOT TO ITS HIGHEST POSITION, AND LIGHTLY
2.
SECURE IT.
INSTALL (2X) 5/16-18 X 1-1/4" HHCS, LOCK WASHERS AND FLAT
3.
WASHERS INTO THE THREADED HOLES ON THE MAIN BASE PLATE.
DO NOT TIGHTEN.
REMOVE TRIM AROUND PASSENGER SEAT.
4.
REMOVE PASSENGER SIDE REAR SEAT BOLTS.
5.
MANEUVER FRONT SEAT HOOKS OUT OF CORRESPONDING
6.
RECTANGULAR FLOOR HOLES.
POSITION MAIN BASE INTO THE VEHICLE, LARGE RECTANGULAR
7.
HOLES SHOULD LINE UP WITH SEAT HOOK HOLES.
PUT THE PASSENGER SIDE SEAT BACK INTO PLACE POSITIONING
8.
THE FRONT SEAT HOOKS FIRST. IT MAY BE NECESSARY TO
POSITION THE PLATE AS FAR TO THE REAR AS POSSIBLE TO ALLOW
THE SEAT TO BE EASILY TILTED FOR INSTALLATION.
REPLACE REAR SEAT BOLTS AND FINGER TIGHTEN.
9.
IF THE BASE WAS SHIFTED TO THE REAR TO INSTALL THE SEAT,
10.
PULL IT AS FAR FORWARD AS POSSIBLE.
IN NON-POWER SEAT APPLICATIONS, THE SINGLE THREADED HOLE
11.
ON THE OUTBOARD EDGE OF THE PLATE SHOULD LINE UP WITH A
HOLE IN THE SEAT RAIL.
IF APPLICABLE, INSTALL THE 1/4-20 X 1/2" HHCS, LOCK WASHER
12.
AND FLAT WASHER THROUGH THE SEAT RAIL INTO THE THREADED
HOLE AND TIGHTEN.
SLIDE TWO TABS INTO THE DRIVERS SIDE SEAT RAIL AND SECURE
13.
WITH (2X) 1/4-20 X 3/4" HHCS, LOCK WASHERS AND FLAT
WASHERS.
ATTACH BASE OFFSET ASSEMBLY TO BASE USING (4X) 5/16-18
14.
3/4" HHCS, (4X) 5/16 SPLIT LOCK WASHER AND (4X) 5/16" FLAT
WASHER.
TIGHTEN 2X 5/16-18 X 1-1/4" BOLTS TO EXTEND SUPPORT FOOT
15.
TO THE FLOORING UNTIL EITHER THE BOLTS ARE FULLY
TIGHTENED OR SUFFICIENT SUPPORT FOR THE BASE HAS BEEN
REACHED.
BASE OFFSET
MAIN BASE
TABS
1/4-20 1/2" LG HHCS
1/4" LOCK WASHER
1/4" FLAT WASHER
(NOT USED FOR
POWER SEAT APPLICATIONS)
4X
5/16-18X 3/4" HHCS
5/16" LOCK WASHER
5/16" FLAT WASHER
2X
5/16-18X 1-1/4" HHCS
5/16"SPLIT LOCK WASHER
5/16" FLAT WASHER
ADJUSTABLE
SUPPORT FOOT
2X
1/4-20X 3/4" HHCS
1/4" LOCK WASHER
1/4" FLAT WASHER
2X
1/4-20X 3/4" HHCS
1/4" LOCK WASHER
1/4" FLAT WASHER
C-HDM-176
INSTALLATION INSTRUCTIONS
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 1 OF 1
DO NOT SCALE DRAWING
WEIGHT (LB): 21.87
TITLE:
DWG. NO.
C-HDM-176_INST
REV
A
A
HAVIS, INC.
INSTALLATION, HDM BASE, 2014
SILVERADO 1500/ 2015 TAHOE
  • Page 1 1

Havis PKG-PSM-276 Installation guide

Havis
Brand
Havis
Model
PKG-PSM-276
Category
Mounting kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents