Panasonic C-HDM-203 Installation guide
- Category
- Mounting kits
- Type
- Installation guide
1
4
3
5
2
A
DETAIL A
1.428
FULLY
COMPRESSED
E
(DISASSEMBLY PROCESS; NOTE THIS SHOULD ONLY BE DONE IN
1.
EXTREME CIRCUMSTANCES).
LOOSEN HANDLE OR BOLT AND TWIST THE COLLAR UNTIL THE SLOT
2.
IN THE POLE IS OPPOSITE THE SLOT IN THE COLLAR.
PULL STRAIGHT UP AND THE COLLAR SHOULD COME OFF WITH THE
3.
INNER POLE.
TO REASSEMBLE REVERSE STEPS 1-3 ENSURING THE SWAGE IS
4.
OPPOSITE THE SLOT IN THE COLLAR WHEN EVERYTHING IS
TIGHTENED UP.
5
2
C
(SKIP IF 2 PIECE SHAFT COLLAR
1.
CLAMP IS NOT IN USE)
INSTALL (ITEM 4) SHAFT COLLAR
2.
ASSEMBLY TO (ITEM 1) INNER POLE.
LOCATE DESIRABLE LIMIT HEIGHT
AND SECURE SHAFT COLLAR CLAMP
USING SUPPLIED HARDWARE AND
5/32 ALLEN WRENCH.
4
(OPTIONAL)
B
LOOSELY ATTACH 2 PIECE SPLIT COLLAR AROUND
1.
LOWER TUBE AS HIGH AS POSSIBLE WITHOUT
CROSSINGTHE HORIZONTAL SLOT. USE 5/32" ALLEN
WRENCH.
ATTACH SUPPORT ARM TO COLLAR USING 1/4 X 3/4
2.
HEX BOLT, SPLIT LOCK WASHER AND FLAT WASHER.
ATTACH "L" BRACKET TO OTHER END WITH 1/4 X 3/4
3.
HEX BOLT, FLAT WASHERS, SPLIT LOCK WASHERS AND
NUT. FIND MOUNTING LOCATION FOR THE "L" BRACKET
UNDER DASH AT GLOBE BOX DOOR HINGE AREA.
(PREFERABLY TO METAL FRAME). SOME VEHICLES
REQUIRE A HOLE TO BE DRILLED.
ADJUST LENGTH OF SUPPORT ARM AS NEEDED.
4.
*** BE CAREFUL OF WIRING, VACUUM LINES ETC ..***
TIGHTEN COLLAR ON POLE WITH 5/32" ALLEN
5.
WRENCH.
TIGHTEN LARGE NUT ON SUPPORT ARM WITH
6.
ADJUSTABLE WRENCH.
3
(OPTIONAL)
SUPPORT COLLAR
MUST NOT BE FIXED
ABOVE HORIZONTAL
SLOT IN HDM POLE.
D
(SKIP IF GAS SHOCK IS NOT IN USE)
1.
REMOVE SMALL PLASTIC DISC OFF THE WIDER
2.
DIAMETER OF THE GAS SHOCK BY UNSCREWING.
INSERT GAS SHOCK FROM THE BOTTOM OF THE
3.
HDM POLE ASSEMBLY.
SCREW SMALL PLASTIC DISC BACK INTO
4.
POSITION.
ATTACH POLE TO C-HDM-100 BASE AND C-HDM-
5.
300 TOP PLATE ADAPTERS, BOTH NOT SHOWN.
COMPRESSING THE GAS SHOCK IN THE PROCESS.
5
(OPTIONAL)
A
1) THE HDM SERIES ADJUSTABLE COLLAR
COMES PRE-ASSEMBLED AND SECURED
FOR SHIPPING PURPOSES USING A HEX NUT.
REMOVE THE HEX NUT USING A 7/16" WRENCH
REPLACE WITH HANDLE FOUND IN HARDWARE KIT.
2) IF ORDERING WITHOUT HANDLE ASSEMBLY WILL
COME WITH A 1/4-20 SHCS PRE INSTALLED.
(1)
(2)
ASSEMBLY INSTRUCTIONS , HDM
200 SERIES, POLE ASSEMBLY
"OUTER POLE
SWAGE TONGUE"
HEAVY DUTY MOUNT POLE
INSTALLATION INSTRUCTIONS
REV.
DESCRIPTION
DATE
BY
CHECKED BY
A
RELEASED TO PRODUCTION
12/03/09
PMELAYA
-----
ITEM NO.
QTY.
DESCRIPTION
1 1
ASSEMBLY, WELDMENT, HDM , OUTER POLE
2 1
ASSEMBLY, ADJUSTABLE COLLAR CLAMP, HDM
3 1
PVC, SPLIT SLEEVE, E-HDM POLE
4 1
GUIDE RING BUSHING, HDM
5 1
ASSEMBLY, WELDMENT, HDM, INNER POLE
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
THE INFORMATION CONTAINED IN THIS DRAWING
IS THE SOLE PROPERTY OF HAVIS SHIELDS
EQUIPMENT CORP. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF HAVIS SHIELDS EQUIPMENT CORP.
IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
ALL DIMENSIONS ARE IN INCHES
ALL THREADS ARE IN UNC-2B OR
UNF-2B AFTER COATING AND
TOLERANCES ARE:
.XX .XXX ANGLES
.02 .010 .5 DEG
MATERIAL:
FINISH: NONE
DRAWN BY:
Paul Melaya
CHECKED BY:
-
SIZE
SCALE: 1:4
UNLESS OTHERWISE SPECIFIED:
SHEET 1 OF 1
DO NOT SCALE DRAWING
REF # C-HDM-200-INST
AREA(SQ. IN.): 472.710
DESIGNED BY:
Dave E'nama
WEIGHT (LB): 6.434
TITLE:
DWG. NO.
REV
SEE BOM
A
C-HDM-200-INST
A
-
1
Panasonic C-HDM-203 Installation guide
- Category
- Mounting kits
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic C-HDM-106 Installation guide
-
-
Panasonic C-HDM-114 Installation guide
-
-
-
-
-
-
-