Citizen CL-E730 User manual

Brand: Citizen

Model: CL-E730

Category: Label printers

Type: User manual

This manual is also suitable for

CL-E720

CL-E720/CL-E730

USER'S

MANUAL

Thermal Transfer Barcode & Label Printer

CONTENTS

INTRODUCTION .............................................................................................................................. 3

COMPLIANCE STATEMENT FOR EUROPEAN USERS ........................................................... 5

GS MARK STATEMENT ................................................................................................................... 5

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS ................................................... 5

EMI COMPLIANCE STATEMENT FOR CANADIAN USERS ................................................... 6

ETAT DE CONFORMITE EMI A L’USAGE DES UTILISATEURS CANADIENS .................... 6

IMPORTANT SAFETY INSTRUCTIONS ...................................................................................... 7

NOTICE ............................................................................................................................................... 8

SAFETY INSTRUCTIONS ................................................................................................................ 9

Chapter 1 Setup

Conrmation of Carton Contents ..........................................................................................11

Part Names and Functions ........................................................................................................13

Connection to Power .................................................................................................................. 20

Driver Installation ........................................................................................................................20

Connection to a Computer .......................................................................................................21

Chapter 2

Printer Operation

Power ON/OFF ..............................................................................................................................22

Normal Operating Mode ........................................................................................................... 23

Setting the Media ........................................................................................................................25

Setting the Ribbon ......................................................................................................................30

Mode Settings ............................................................................................................................... 33

Quick Setup of the Print Method ...........................................................................................52

Emulation Auto Detect: Cross-Emulation

........................................................................ 53

Chapter 3

Printer Adjustments

Sensor Adjustments .................................................................................................................... 55

Media Thickness Adjustment ..................................................................................................59

Media Width Adjustment .......................................................................................................... 60

Adjusting the Ribbon .................................................................................................................61

Cleaning ..........................................................................................................................................67

Appendixes

Troubleshooting ........................................................................................................................... 68

Specications ................................................................................................................................71

Interfaces ........................................................................................................................................76

Replacing the Interface Board .................................................................................................89

■■■

Main Features

■■■

<High-speed, high-quality printing>

This printer can be used for high-speed, high-quality printing thanks to its ARM® Cortex-A9

processor and Citizen’s history control IC.

*ARM and Cortex are registered trademarks or trademarks of ARM Limited.

<Environment-friendly energy-ecient design>

As an energy-ecient product, this printer is compliant with the International Energy Star

Program (ENERGY STAR®).

<Optimal ribbon tension through ARCP

Designed to provide the optimal ribbon tension from the beginning to the end of the ribbon

roll, the ARCP

technology insures stable printing position & printed output accuracy by

preventing ribbon slippage and ribbon wrinkle.

Label creation and printing is easily accomplished through the use of printer control

language emulations. This printer can process either ZPL

or DPL

as standard.

• The printer status can be seen easily and its conguration & setup adjusted easily using

the graphic LCD panel.

• The high-lift printhead and mechanism means that media and ribbon can be loaded with

ease and it is constructed for easy thermal printhead cleaning, etc.

• Media width adjustment, media thickness adjustment, media sensor adjustment, and

ribbon tension adjustment can all be accomplished easily by the user using the colour-

coded operator controls.

Ethernet (LAN) and USB 2.0 are standard equipment, for quick data transfer and printing.

Optional RS232C Serial, IEEE1284 Parallel and Wireless LAN (WiFi) are all quickly installed.

The auto-cutter and peeler units are designed so that they can be installed easily.

INTRODUCTION

Thank you for purchasing the CITIZEN CL-E720/CL-E730 printer. This printer is compatible with the maximum

media width (118 mm or 4.65 inch), which has been developed for a wide range of applications such as

labels, tags and tickets.

The adjustable media sensors - which allow the sensors to be positioned in dierent

locations across the media - are standard features making the printer ideal for use with

special media.

The interface, power switch etc. are installed towards the back and the top cover opens and

closes vertically so that the sides of the printer are not restricted.

COMPLIANCE STATEMENT

FOR EUROPEAN USERS

CE marking shows conformity to the following criteria and provisions:

Low Voltage Directive (2006/95/EC, formerly 73/23/EEC)/EN60950-1

EMC Directive (2004/108/EC, formerly 89/336/EEC)/EN55022, EN55024, EN61000-3-2 &

EN61000-3-3

GS MARK STATEMENT

This product has been tested under EN ISO 7779 and has an acoustic level output no higher than

70db(A).

This device is not intended for use at a video workstation in compliance with Bildscharb V.

This device is not intended for use in the direct eld of view at visual display workplaces. To avoid

incommoding reections at visual display workplaces this device must not be placed in the direct

eld of view.

FCC COMPLIANCE STATEMENT

FOR AMERICAN USERS

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

EMI COMPLIANCE STATEMENT

FOR CANADIAN USERS

This Class A Information Technology Equipment (ITE) complies with Canadian CAN ICES-

3(A)/NMB-3(A).

This equipment generates and uses radio frequency energy and if not installed and used

properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference

to radio and television reception. This Information Technology Equipment (ITE) does not

exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio

Interference Regulations of the Canadian Department of Communications. This equipment is

designed to provide reasonable protection against such interference in a residential installation.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentandreceiver.

•Connecttheequipmentintoanoutletonacircuitdierentfromthattowhichthereceiveris

connected.

•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

CAUTION: Use shielded cables to connect this device to computers.

Any changes or modications not expressly approved by the grantee of this device

could void the user’s authority to operate the equipment.

ETAT DE CONFORMITE EMI A L’USAGE

DES UTILISATEURS CANADIENS

Cet Équipements informatiques (EI) de la classe A est conforme à la norme CAN ICES-3(A)/

NMB-3(A) du Canada.

Cet équipment produit et utilise l’énergie à radiofréquences et s’iln’est pas installé et utilisé

correctment, c’esst à dire en accord strict avec les instructions du fabricant, il risque de provoquer

des intérferences avec la réception de la radio et de latélévision.

Le présent Équipements informatiques (EI) n’émet pas de bruite radio électriques dépassant les

limites applicables aux appareils numériques de la classe A prescrites dans le Réglement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

Cet équipment est conçu pour fournir une protection satisfaisante contre de telles interférences

dans une installation résidentielle. Cependant, il n’y a pas de garantie contre les interférences

avec les réceptions radio ou télévision, provoquées par la mise en et hors circuit de l’équipment;

aussi, il est demandé a l’utilisateur d’essayer de corriger l’interférence par l’une ou plus des

mesures suivantes:

•Réorienterl’antennederéception.

•Installerl’ordinateurautrepart,parégardpourlerécepteur.

•Brancherl’ordinateurdansuneprisedecourantdiérentedefaçonàcequel’ordinateuretle

récepteur soient branchés sur des circuits diérents.

IMPORTANT SAFETY INSTRUCTIONS

• Readalloftheseinstructionsandsavethemforlaterreference.

• Followallwarningsandinstructionsmarkedontheproduct.

•Unplugthisproductfromthewalloutletbeforecleaning.Donotuseliquidoraerosolcleaners.Usea

damp cloth for cleaning.

• Donotusethisproductnearwater.

•Donotplacethisproductonanunstablecart,standortable.Theproductmayfall,causingserious

damage to the product.

• Slotsandopeningsonthecabinetandthebackorbottomareprovidedforventilation.

To ensure reliable operation of the product and to protect it from overheating, do not block or cover these

openings. The openings should never be blocked by placing the product on a bed, sofa, rug or other

similar surface. This product should never be placed near or over a radiator or heat register. This product

should not be placed in a built-in installation unless proper ventilation is provided.

• Thisproductshouldbeoperatedfromthetypeofpowersourceindicatedonthemarkinglabel.

If you are not sure of the type of power available, consult your dealer or local power company.

• Thisproductisequippedwithathree-prongedplug,aplughavingathird(grounding)pin.Thisplugwill

only t into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into

the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the

grounding-type plug.

• Donotallowanythingtorestonthepowercord.Donotlocatethisproductwherethecordwillbewalked

on.

•Ifanextensioncordisusedwiththisproduct,makesurethatthetotaloftheampereratingsonthe

products plugged into the extension cord do not exceed the extension cord ampere rating. Also, make

sure that the total of all products plugged into the wall outlet does not exceed 15 amperes for 120V outlet

and 7.5 amperes for 220V-240V outlet.

•Neverpushobjectsofanykindintothisproductthroughcabinetslotsastheymaytouchdangerous

voltage points or short out parts that could result in a risk of re or electric shock. Never spill liquid of any

kind on the product.

• Exceptasexplainedelsewhereinthismanual,don’tattempttoservicethisproductyourself.Openingand

removing those covers that are marked “Do Not Remove” may expose you to dangerous voltage points or

other risks. Refer all servicing on those compartments to service personnel.

• Themainsplugonthisequipmentmustbeusedtodisconnectmainspower.Pleaseensurethatthesocket

outlet is installed near the equipment and shall be easily accessible.

•Unplugthisproductfromthewalloutletandreferservicingtoqualifiedservicepersonnelunderthe

following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally when the operating instructions are followed. Adjust only

those controls that are covered by the operating instructions since improper adjustment of other

controls may result in damage and will often require extensive work by a qualied technician to restore

the product to normal operation.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance, indicating a need for service.

• ForNorwayUser

The equipment has been designed for connection to IT power distribution system.

NOTICE

• Beforeuse,besuretoreadthismanual.Pleasekeepthismanualforfuturereferenceasneeded.

• Thecontentsofthismanualmaychangewithoutpriornotice.

•Reproduction,transfer,ortransmissionofthecontentsofthismanualwithoutpriorconsentisstrictly

prohibited.

• Wearenotliableforanydamageresultingfromtheuseoftheinformationcontainedherein,regardlessof

errors, omissions, or misprints.

• Wearenotliableforanyproblemsresultingfromtheuseofoptionalproductsandconsumablesupplies

other than the designated products contained herein.

• Donothandle,disassembleorrepairthepartsotherthanthosespeciedinthismanual.

• Wearenotliableforanydamagecausedbymisuseoftheprinterorusageoftheprinterinpoor

environmental conditions.

• Dataresidingintheprinteristemporary.Therefore,alldatawillbelostifpowerislost.Wearenotliablefor

any damage or loss of prots caused by data loss due to failures, repairs, inspections, etc.

• Pleasecontactusifthereareanymistakesorambiguitieswithinthismanual.

• Iftherearemissingorincorrectlycollatedpagesinthismanual,contactustoobtainanewmanual.

Visit the following site to get documentation, drivers, utilities, and other information.

http://www.citizen-systems.co.jp/english/support/index.html

CITIZEN is a registered trademark of CITIZEN HOLDINGS CO., Japan.

CITIZEN es una marca registrada de CITIZEN HOLDINGS CO., Japón.

SAFETY INSTRUCTIONS

which must be strictly observed !

• Topreventpersonalinjuryorpropertydamage,thefollowingshallbestrictlyobserved.

• Thedegreeofpossibleinjuryanddamageduetoincorrectuseorimproperlyfollowing

instructions is described below.

Indicatesasituationwhich,ifnotobservedandhandled

properly,couldresultindeathorseriousinjury.

Indicatesasituationwhich,ifnotobservedandhandled

properly,couldresultininjury.

:This is a mark to call attention to the reader.

Warning

Caution

Warning

Neverperformthefollowing.Ifnotavoided,thesemaycausedamageortroubleto

the printer or cause the printer to overheat and release smoke and cause burns or an

electricalshock.Iftheprinterisdamagedorismalfunctioning,besuretoturnthe

printeroimmediatelyandremovethepowercordfromtheoutlet,thenconsultour

service personnel.

• Donotjoltorimpacttotheprinterbysteppingon,droppingorhittingtheprinter.

• Donotplacetheprinterinapoorlyventilatedarea,orshutotheairventoftheprinter.

• Donotplacetheprinterwherechemicalreactionsoccur,suchasinlaboratoriesorwhereairis

mixed with salt or gas.

• Donotuseapowervoltageorfrequencyotherthanthosespecied.

• Donotplug/unplugthepowercordorattach/detachtheinterfacecablebysimplygrabbingthe

power cord or interface cable. Do not pull or carry the printer when the tension of the power cord

or interface cable is increased.

• Donotdroporputforeignmattersuchasclipsandpinsintotheprinter.Thismaycauseproblems.

• Donotplugthepowercordintoanoutletwithmanyloads.

• Donotspilldrinkssuchastea,coeeandjuiceontheprinterorsprayinsecticideontheprinter.

If drink or water is spilled, rst be sure to turn the power o and remove the power cord from the

outlet, then consult our service personnel.

• Donotdisassembleormodifytheprinter.

Discard or safely store the plastic packing bag. This bag should be kept away from

children.Ifthebagispulledoverachild’shead,itmaycausesuocation.

General Precautions

Caution

• Priortooperation,readthesafetyinstructionscarefullyandobservethem.

• Donotdroporputforeignmattersuchasclipsandpinsintotheprinter.Thismaycauseproblems.

• Becarefulwhenmovingorcarryingtheprinter.Droppingtheprintermaycauseinjuryorproperty

damage.

• Makesureifyouopenthetopcover,itisopenedalltheway.Ifonlypartiallyopen,thecovercould

slam shut, possibly causing injury.

• Whenthecoverisopen,becarefulofthecornersofthecover.Theycouldcauseinjury.

• Donotopentheprinterduringprinting.

•Whencleaningthesurfaceoftheprintercase,donotusethecloththatissoakedinthinner,

trichloroethylene, benzine, ketone or similar chemicals.

• Donotusetheprinterwherethereisalotofoil,ironparticles,ordust.

• Donotspillliquidsorsprayinsecticideontheprinter.

• Donotjoltorimpacttotheprinterbysteppingon,droppingorhittingtheprinter.

• Operatethecontrolpanelproperly.Acareless,roughhandlingmaycauseproblemsormalfunction.

Do not use such sharp-edged tool as a ballpoint pen for operation.

• Becarefuloftheedgesoftheplatessoinjuryorpropertydamageispossible.

• Ifaproblemoccursduringprinting,stoptheprinterimmediatelyandunplugthepowercordfrom

the outlet.

• Whenprintertroubleoccurs,donottrytodissembleit.Instead,consultourservicepersonnel.

Precautions When Installing the Printer

• Priortooperation,readthesafetyinstructionscarefullyandobservethem.

• Donotuseorstoretheprinternearre,excessivemoisture,indirectsunlight,nearanairconditioner

or heater or other source of unusually high or low temperature or humidity or excessive dust.

• Donotplacetheprinterwherechemicalreactionsoccur,suchasinalaboratory.

• Donotplacetheprinterwhereairismixedwithsaltorgas.

•Theprintermustsitonafirm,levelsurfacewherethereisampleventilation.Neverallowthe

printer’s air vent to be blocked by a wall or other object.

• Donotputanythingonthetopofprinter.

•Donotplacetheprinterneararadioortelevision,anddonotusethesamewalloutletforthe

printer and radio or television. Radio or television reception could be adversely aected.

• Donotuseapowervoltageorfrequencyotherthanthosespecied.

• Donotputanythingonthepowercordorsteponit.

• Donotdragorcarrytheprinterwiththepowercordorinterfacecable.

• Avoidpluggingthepowercordintoanoutletwithmanyloads.

• Donotbundlethepowercordwheninsertingtheplug.

• Alwaysgriptheplughousing,notthecord,toplug/unplugthepowercord.

• Makecertainthepoweristurnedobeforeconnecting/disconnectingtheinterfacecable.

•Avoidlengtheningthesignalcableorconnectingittoanynoise-producingdevice.Ifitis

unavoidable, use the shielded cable or twisted pair for each signal.

• Placetheprinterneartheoutletwherethepowercordcanbeunpluggedeasilytoshutopower.

• UsetheACoutletthatacceptsathree-prongedplug.Otherwise,staticelectricitymaybegenerated

and there will be danger of electric shock.

Caution

Chapter 1 Setup

Conrmation of Carton Contents

Check that the following accessories are included with the printer in the

carton.

Printer

[Model CL-E720/CL-E730]

Head cleaner Media holder guide Media holder bar

Test label media

CD-ROM

(User’s Manual)

Power cord

Quick-start guide

Safety Instructions

Sample ribbon Paper core (for ribbon)Ribbon holder

Note: The empty carton and packing materials should be stored for

future shipping of the printer.

Chapter 1 Setup

Caution

• Be careful when moving or carrying the printer and when taking

the printer out of the carton. The printer may cause injury or

property damage if dropped. Be sure to grip the printer housing

rmly when taking it out of the carton. Do not grip the printer by

the foam packing material which may break, causing the printer

to drop.

• When opening the cover, open it all the way. If only part way

open, the cover could slam shut, possibly causing injury.

• Be careful of the edge of the cover when the cover is opened. It

may cause injury or property damage.

• Be careful of the edges of the metal plates so injury or property

damage is possible.

Conrmation of Carton Contents

Chapter 1 Setup

Part Names and Functions

Front View

Top cover window

The amount of ribbon and media remaining can be checked through

this window.

Top cover

Is opened vertically to set media or ribbon.

Operation panel

This is used to make changes and adjustments to the printer and its

conguration

Operation panel (p.18)

Chapter 1 Setup

Part Names and Functions

Inside the printer

Media holder guide

This guide is moved horizontally to match the media size. The guide

can be sliding it from the holder bar.

Media holder bar

The media is supported by the media holder bar when installed in the

printer.

Ribbon drive unit

Head close knob

Push the head close knob to lock the mechanism closed. If you push

on another part of the mechanism, the printer may not lock closed

correctly.

Front cover

It is removed to install optional units such as the peeler or cutter.

Ribbon holder

It is used to attach the ribbon and paper core.

Setting the Ribbon (p.30)

Chapter 1 Setup

Large blue-head open lever

The head unit can be raised to install media by pushing this lever.

It locks the head unit during printing.

Media width adjustment dial

It is adjusted to match the width of the media.

Media thickness adjustment dial

It is adjusted to match the thickness of the media.

Front (winding side) ribbon tension adjustment knob

This is adjusted according to the width of the ribbon that is used. It is

also used when the ribbon is wrinkled or slips.

Front (winding side) ribbon left-right balance adjustment

knob

It is used to perform an adjustment when the ribbon is wrinkled.

Normally set it to the center position.

Media Width Adjustment

(p.60)

Media Thickness Adjustment

(p.59)

Ribbon Tension Adjustment

(p.61)

Ribbon Balance Adjustment

(p.63)

Part Names and Functions

Chapter 1 Setup

-2

-1

-2

-1

Thermal printhead

This is the printhead. Avoid touching this with your ngertips and

leaving grease or dirt on the printhead surface.

Sensor arm

The media can be installed by raising this arm.

The media can be held in place by lowering this arm.

Upper sensor (

-1) and bottom sensor (

-2)

When used as a transparent sensor (for labels and tags with notches),

it is used by matching the sensor markings of the upper sensor and

the bottom sensor. When used as a reective sensor, it is used by

matching the sensor marking on the bottom sensor with the position

of the black mark on the liner or media backing.

Media guides

Left xed media guide (

-1) and right movable media

guide(

-2)

The end of the media is matched to the left xed media guide, then

the right side movable media guide is moved horizontally to match

it to the media size. And the movable media guide is used as a guide

to match the upper sensor and bottom sensor when using the

transparent sensors.

Platen

Interlocked with the thermal printhead, it feeds media backwards or

forwards.

Media damper

When roll paper is used, this prevents marking on the media especially

at higher print speeds.

Setting the Media (p.25)

Setting sensor positions

(p.28)

Sensor Adjustments (p.55)

Part Names and Functions

Chapter 1 Setup

Rear (feeding side) ribbon tension adjustment knob

The adjustment is done according to the width of the ribbon to be

used. It is adjusted when slippage or wrinkling appears in the ribbon.

Ribbon guide adjusting cam

Adjustment can eliminate the slack in ribbon and prevent occurrence

of wrinkles.

Ribbon guide shaft

It guides the ribbon to be fed.

Optional unit connector cover

It is opened when the cables of the cutter unit and the peeler unit are

connected. Do not remove during normal use.

Part Names and Functions

Ribbon Tension Adjustment

(p.61)

Ribbon guide adjustment

(p.65)

Chapter 1 Setup

Part Names and Functions

Operation panel

2 4

3 6

LCD display

This displays the operational status of the printer and the menu

settings.

Pause key

This temporarily stops printing.

LED

This is lit when the printer power is on. (green)

This is lit when the printer is in an alarm or error status. (red)

Stop key

This stops printing or cancels the alarm.

MENU key

This key enters the menu setting mode or reprints the nal label,

depending on printer status.

Feed key

This key feeds the media to the top of the next label or form.

Normal Operating Mode (p.23)

LED Functions (p.24)

Chapter 1 Setup

Part Names and Functions

Rear View

Power switch

The is the power switch for the printer.

Power cord inlet

The connector of the enclosed power cord is connected here.

Fanfold paper insertion slot

If you want to use fanfold paper, insert the media into this slot from

outside the printer.

Option interface

Optional interface board can be installed by removing the interface

cover. Contact your retailer if you want to use the option interface.

USB interface (USB2.0)

This receives USB transmission of data from a host computer.

Ethernet interface

Data from host computer is received via wired LAN communication.

NOTE: Do not connect the USB cable to the wired LAN connector.

Doing so may damage the connector.

Replacing the Interface Board

(p.89)

USB Interface (p.76)

Connection to Power (p.20)

Ethernet Interface (p.77)

Power ON/OFF (p.22)

Chapter 1 Setup

Connection to Power

1. Check that the power switch to the printer is turned OFF.

2. Connect the connector of the power cord to the power cord

inlet on the printer.

3. Insert the plug of the power cord in the AC outlet.

Power Cord Inlet

AC Outlet

Driver Installation

The computer may automatically detect the presence of the new printer

when it is rst started, depending on the computer type, interface and

operating system. Follow any on-screen instruction and also instructions

supplied with any additional CD-ROM disk included with your printer.

Your supplier will assist you with the correct drivers and software which

are compatible with your particular computer system.

Use an AC outlet that accepts a three-pronged plug. Otherwise,

static electricity may be generated and there will be danger of

electric shock.

Caution

Page is loading ...

Citizen CL-E730 User manual

Brand: Citizen

Model: CL-E730

Category: Label printers

Type: User manual

This manual is also suitable for

CL-E720

Download PDF

report

Citizen CL-E730 User manual

This manual is also suitable for

Citizen CL-E730 User manual

Related papers

Other documents