Bradley 6324-SR Installation guide

Brand: Bradley

Model: 6324-SR

Category: Sanitary ware

Type: Installation guide

Soap Reservoir for

3060 Series Lav

Decks

Model No. 6324-SR

Installation

Instructions

FOR SERVICE ONLY

215-1304 Rev. B; EN 03-1101

Page 1 of 4 8/11/03

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone (262) 251-6000 Fax (262) 251-5817

http:\\www.bradleycorp.com

Table of Contents

Assembly of Components . . . . . . . . . . . . . . . . . . . . . .2

Rough-In Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . .3-4

Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . .4

IMPORTANT

Read this entire instruction sheet to

ensure proper installation.

File these instructions with the owner or

maintenance department.

Soap Reservoir for 3060 Series Lav Decks

6324-SR Installation Instructions - FOR SERVICE ONLY

8/11/03 Bradley Corporation • 215-1304 Rev. B; EN 03-1101

Assembly of Components

Check Contents

Separate all parts from packaging and check each part with the drawing below. Make sure all parts

are accounted for before discarding any packaging material. If any parts are missing, do not attempt

to install your Bradley Lav Deck Soap Dispenser until you obtain the missing parts.

Bradley Soap Reservoir Warranty

Bradley Corporation warrants to commercial and institutional purchasers only each unit free from defects in material and

workmanship under normal use and service upon the following terms and conditions:

1. This warranty is limited to replacing or repairing, at our option, transportation charges prepaid by the purchaser, any

Bradley unit or part thereof which our inspection shall show to have been defective within the limitations of this war-

ranty.

2. The period during which Terreon

Lavatory System components are warranted is as follows:

• Terreon

components warranted for two years

• All other Lavatory System components warranted for one year.

3. This warranty does not cover installation or any other labor charges and does not apply to any units which have been

damaged by accident, abuse, improper installation or improper maintenance.

4. The replacement or repair of defective units as stated in this warranty shall constitute the sole remedy of the purchaser

and the sole liability of Bradley Corporation under this warranty. Bradley Corporation shall not otherwise be liable

under any indirect damages caused by defects in the repair or replacement thereof.

5. This warranty extends only to commercial and institutional purchaser and does not extend to any others, including con-

sumer customers of commercial institutional purchasers.

6. This warranty is in lieu of all other warranties, expressed or implied, including any implied warranty of mer-

chantability or fitness for a particular purpose or otherwise.

Soap Reservoir for 3060 Series Lav Decks

Installation Instructions - FOR SERVICE ONLY 6324-SR

Bradley Corporation • 215-1304 Rev. B; EN 03-1101 8/11/03

6324-SR Soap Reservoir Rough-In Dimensions

Installation Instructions

Step 1: Connect filler tubing to reservoir

1. Assemble the filler components (cap, body,

nut and washer) to the Lav Deck as

shown in Figure 2.

2. Connect the male elbow to the reservoir

as shown in Figure 2.

3. Connect one end of the filler tube to the

male elbow on the soap reservoir and

secure the tube with the hose clamp pro-

vided (see Figure 2).

Step 2: Mount soap reservoir to wall

1. Install the hanger brackets to the wall at

the locations shown in Figure 1.

2. Place the soap reservoir assembly onto

the hanger brackets as shown in Figure 1.

3. Connect the other end of the 5/8" filler

tube to the male connector on the filler

assembly and secure the tube with the

hose clamp provided (see Figure 2).

Installation Instructions continue...

Figure 1

Figure 2

Soap Reservoir for 3060 Series Lav Decks

6324-SR Installation Instructions - FOR SERVICE ONLY

8/11/03 Bradley Corporation • 215-1304 Rev. B; EN 03-1101

Installation Instructions continued . . .

Step 3: Install soap dispensers and supply tubes

1. Insert the shank through the hole in the Lav Deck and secure

the shank to the Lav Deck with the washer and nut provided.

NOTE: For ease of installation, moisten the end of the tube before

inserting into the 7/8" O.D. vinyl tube. The tube must be fully

inserted into the reservoir for the soap to properly dispense (see

Figure 3).

2. Insert the supply tube into the soap reservoir through the rub-

ber grommet as shown in Figure 3.

Step 4: Fill soap reservoir

NOTE: The soap system dispenses vegetable/coconut oil liquid

soaps, synthetic detergents, viscous lotion soaps and antiseptic

solutions. A 10-15% concentration is recommended for vegetable

and coconut oil soaps. All other soaps and solutions require no

dilution. Reservoir capacity is 1.5 gallons.

1. Remove the filler cap using the soap wrench provided.

2. Pour the soap into the filler assembly.

3. Install the filler cap and prime both of the soap valves until soap is dispensed.

Changing soap type

1. If your Lav Deck is equipped with an optional access panel, remove the panel from the deck.

2. Disconnect the filler tube from the soap reservoir at the male connector by first removing the

hose clamp, then removing the tube.

3. Disconnect the supply tubes from the reservoir by pulling the tubes out of the 7/8" O.D. vinyl

tubing.

4. Remove the soap reservoir from the hanger bracket.

5. Pour out all of the old soap in the reservoir, utilizing the drain plug. Then fill the reservoir with

hot water. Shake the reservoir to loosen any soap residue and rinse repeatedly until it is clean.

Allow to air dry.

6. Place the soap reservoir on the hanger bracket and reinstall the filler and supply tubes following

the procedures outlined in Step 2 on page 3, and Step 3 above.

7. Refill the soap reservoir following the procedures outlined in Step 4 above.

Cleaning the soap dispenser and reservoir

NOTE: Monthly cleaning of the soap system is recommended to ensure optimum performance and

maximum service life.

Clean exterior: Use warm water and soap to clean the soap valves. Dry with a soft cloth.

Clean interior: Inspect the interior of the soap reservoir for residue and/or coagulation of soap.

Clean and refill the soap tank following the procedures outlined in Changing soap type above.

Clean internal components: To clean the internal components of the soap dispenser, pump hot

water through the soap system until a clean flow of water comes out of the valve.

Figure 3

Bradley 6324-SR Installation guide

Brand: Bradley

Model: 6324-SR

Category: Sanitary ware

Type: Installation guide

Download PDF

report

Bradley 6324-SR Installation guide

Bradley 6324-SR Installation guide

Related papers

Other documents