2. Integra
  3. DRX-2.3

Integra DRX-2.3 Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Integra DRX-2.3 Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
a
b
c
Install & Connections
DRX-2.3
AV Receiver
a
b
2
4-16Ω
1 2
3
ᴧº
1/2˝
(12 mm)
ᴧ
a
3
1
1 2 3
*29403587*
SN 29403587 F1812-0
Initial Setup Guide
http://integraworldwide.com/manual/drx23/top.pdf
Refer to the instruction
manual available on our
website to install and
connect speaker systems
other than 7.1 ch.
http://integraworldwide.com/manual/drx23/top.pdf
Refer to the instruction manual available
on our website to install and connect
speaker systems other than 7.1 ch.
a: 22° to 30°, b: 90° to 110°, c: 135° to 150°
a Speaker cable, b Subwoofer cable
Front Speakers
Center Speaker
Surround Speakers
Powered Subwoofer
Surround Back Speakers
1,2
3
4,5
6
7,8
7.1 ch System
SN29403587_DRX-2.3_QSG_En.indd 1 2018/12/21 9:41:43
BD/DVD Cable/Satellite set-top box
Streaming
media playerGAME
ARC TV
c
Non-ARC TV
c + d
IN
(
ARC
)
d
ARC
c
DIGITAL
OPTICAL OUT
5
4
5
4 5
6
Initial Setup with Auto Start-up Wizard
Inputs
TV
HDMI 1
HDMI 2
HDMI 3
Initial Setup
TV
INPUT
TV’s REMOTE
6
Speaker Channels
Subwoofer
Height Speaker
Zone Speaker
Bi-Amp
Speaker Impedance
6ohms or above
< >
7.1 ch
Yes
No
No
-
-
-
To redo the initial setup
“8. Miscellaneous”
“4.Initial Setup”
c HDMI cable
d Digital optical cable
1
Used during Initial Setup.
2
Connect speakers with 4 Ω to 16 Ω impedance. If any of the connected speakers have 4 Ω or more to
less than 6 Ω impedance, in “Initial Setup”, “Speaker Setup”, set “Speaker Impedance” to “4ohms”.
3
Make sure the wires at the ends of the speaker cables are twisted tightly and do not stick out of the
speaker terminals when connecting. The unit can be damaged if the exposed wires of the speakers touch
the rear panel or the + and - wires touch each other.
4
Choose an HDMI IN jack on the TV that supports ARC when connecting. Settings are required to use the
ARC function. Select "Yes" for "ARC Setup" in "Initial Setup".
5
If you connect this unit to the network using wired LAN, connect an LAN cable to the ETHERNET port.
6
Switch the input on the TV to that assigned to the unit. Follow the guidance displayed on the screen to
complete Initial Setup. If you selected “No, Skip” for “ARC Setup” in the Initial Setup, to enable HDMI
CEC and HDMI Standby Through function, after completing Initial Setup, you will need to press
on the
remote controller and make the settings in “6. Hardware” - “1. HDMI”.
Tips
When the unit is operating erratically
If operation becomes unstable, try restarting the unit. Set the unit to standby,
then press and hold
On/Standby
on the main unit for 5 seconds or more.
If restarting doesn’t x the problem, try unplugging the power cord and HDMI
cables then replugging them in again, initializing settings (with the unit ON, while
pressing CBL/SAT on the main unit, press
On/Standby
.), and trying Firmware
Update.
5"
(North American
models)
(Australian models)
SN29403587_DRX-2.3_QSG_En.indd 2 2018/12/21 9:41:47
/