Duerkopp Adler 878-M PREMIUM User manual

Category
Sewing machines
Type
User manual
878 PREMIUMFacts and USP
Programmable electronic
Programmable
Threading procedure
thread tension
(optional)
Operation panel
OP 3000
top roller lift
(max. 13 mm)
Powerful
direct drive
M-TYPE PREMIUM
Programmable
top roller constant
pressure
Keypad for the
most common
functions
Integrated LED
sewing light
Bottom wheel feed with
possibility of differential
between the top roller
and wheel feeder
(without needle transport)
Automatic thread trimmer
(length of remaining
thread approx. 10 mm)
Vertical hook
L (26 mm)
Thread monitor
for hook thread
(optional)
Electronic hand wheel
(Jog-Dial)
Blocking machine run
after opening the cover
hook (optional)
Integrated bobbin winder
with winding assistant
Stop button
for service
Programmable stitch length
adjustment (max. 7 mm)
including back tack and
short stitch length
Control unit DAC comfort
(max. 999 sewing programs
with max. 30 seam sections)
Electronic knee switch
with a choice of function
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
Basic
information
Programmable favorite
button
Program 000 Manual mode
Stitch length
Thread tension (optional)
Top roller pressure
Differential
Other parameters
Programming mode
1. Select programing mode.
.
TEACH-IN
1. Press button.
〉〉
2. Set the parameters.
3. Select
and sew for the first seam section.
4. Press
button to activate the next seam section; if necessary,
readjust parameters and sew for the next seam section.
Perform for all desired seam sections.
5. Press pedal back → Program is saved, display
switches to Edit mode.
Assigning functions to
the favorite button
1. Press button.
Use numeric buttons to change program number.
4. Press OK button.
MANUAL PROGRAMMING (Edit mode)
Fine adjustment is possible.
Press
ESC
Program is saved.
Delete program
1. Select program to be delete.
2. Press
P
button.
1.
Press
button to select
1 seam section
.
(1) Threading mode
(2) Backtack
(3) Back tack suppression/recall
(4) Top roller position
(5) Needle position (up/down)
(6) New program
(7) Other functions
2.
Press desired function and favorite button at the same time.
Favorite button has been assigned; function appears on the start screen.
2. Press
button to add a seam section.
3. Enter parameters for the selected seam section.
4. Press
button to activate the next seam section.
Press
button to add a seam section
.
5. Enter values for the selected seam section.
Perform for all desired seam sections.
6. Press
ESC
Program is saved.
3. Press button.
4. Press button.
→ Program is deleted.
5. Press
ESC
.
Program selection is active.
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
© Dürkopp Adler AG 0791 878701 EN - 01.0 - 03/2019
2. Press button.
3. Press button.
1
+
Change of
difference
sense
Automatic
material
thickness
detection
Stitch counter
0,2
  • Page 1 1
  • Page 2 2

Duerkopp Adler 878-M PREMIUM User manual

Category
Sewing machines
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI