GE Appliances UVC7300SLSS Owner's manual

Brand: GE Appliances

Model: UVC7300SLSS

Category: Cooker hoods

Type: Owner's manual

This manual is also suitable for

UVC7300SLSS

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label on

the inside of the hood.

ESPAÑOL

Para consultar una version en

español de este manual de

instrucciones, visite nuestro sitio de

internet GEAppliances.com.

INSERT HOODS

Custom

49-80797-3 01-19 GEA

SAFETY INFORMATION ...........3

USING THE HOOD

Controls ................................5

Chef Connect ...........................6

CARE AND CLEANING

Filters ..................................7

Surfaces ................................8

Lights ..................................8

INSTALLATION INSTRUCTIONS ..9

TROUBLESHOOTING TIPS ........ 17

LIMITED WARRANTY ............. 18

ACCESSORIES ..................... 19

CONSUMER SUPPORT ............20

UVC7300

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

GE is a trademark of the General Electric Company. Manufactured under trademark license.

2 49-80797-3

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-80797-3 3

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

B. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting

means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the

service panel.

C. Do not use this unit with any solid-state speed

control device.

D. This unit must be grounded.

CAUTION

FOR GENERAL VENTILATING USE

ONLY. DO NOT USE TO EXHAUST HAZARDOUS

OR EXPLOSIVE MATERIALS AND VAPORS.

CAUTION

TO REDUCE RISK OF FIRE AND

TO PROPERLY EXHAUST AIR, BE SURE TO DUCT

AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO

SPACES WITHIN WALLS OR CEILINGS OR INTO

ATTICS, CRAWL SPACES OR GARAGES.

WARNING

TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING*:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do

not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher,

and you already know how to operate it.

2. The fire is small and contained in the area where

it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety” published by NFPA.

4 49-80797-3

How to Remove Protective Shipping Film and Packaging Tape

Carefully grasp a corner of the protective shipping film

with your fingers and slowly peel it from the appliance

surface. Do not use any sharp items to remove the film.

Remove all of the film before using the appliance for the

first time.

To assure no damage is done to the finish of the

product, the safest way to remove the adhesive from

packaging tape on new appliances is an application of

a household liquid dishwashing detergent. Apply with a

soft cloth and allow to soak.

NOTE: The adhesive must be removed from all parts.

NOTE: For further cleaning instructions/suggestions,

please refer to the Care and Cleaning section.

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on

medium settings.

B. Always turn hood ON when cooking at high heat or

when flambéing food (i.e. Crepes Suzette, Cherries

Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware

appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with all

applicable codes and standards, including fire-rated

construction.

B. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s

guidelines and safety standards such as those

published by the National Fire Protection

Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE) and the local code authorities.

C. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. When applicable, install any makeup (replacement)

air system in accordance with local building

code requirements. Visit GEAppliances.com for

available makeup air solutions.

F. Turn off breaker to adjacent rooms while working.

WARNING

TO REDUCE THE RISK OF FIRE,

USE ONLY METAL DUCTWORK.

Ŷ'RQRWDWWHPSWWRUHSDLURUUHSODFHDQ\SDUWRI\RXU

hood unless it is specifically recommended in this

manual. All other servicing should be referred to a

qualified technician.

49-80797-3 5

Controls

USING THE HOOD: Controls

1. Rangehood Control Panel: The control panel

is located on the front of the canopy. The position

and function of each control button are noted below.

2. Fan On/Off Button: On/Off switch for the fan.

The fan can be operated by pressing any of the fan

setting buttons. Hold for 3 seconds to activate Delay

Off feature, which automatically turns the fan off

after 15 minutes.

3. Fan Setting Button: Speed control for the

fan. Press the Low button for LOW speed, Med for

MEDIUM speed, and High for HIGH speed. Hold

down the High button for 3 seconds to activate the

BOOST speed that will run for 10 minutes.

On Remote, press Up to increase fan speed, press

Down to decrease fan speed, including Boost.

4. Light Button: On/Dim/Off switch for the LED

lights. Press the Light button to turn the lights on,

again to set the lights to dim setting, and again to

turn the lights off.

5. Chef Connect: This is a Bluetooth

pairing feature

for use with other compatible Chef Connect enabled

products on a cooktop or range. When the device is

paired, the light and fan will turn ON at the Default

Sync Settings upon receiving a command from the

range or cooktop. It will remain ON at that setting until

the user changes it. To pair devices, hold down the

Chef Connect button for 3 seconds. To turn it back

off, hold the button down for another 3 seconds, see

the Chef Connect section for details.

6. Chef Connect Indicator Light: Light will turn

on when Chef Connect is paired.

7. IR Sensor: Remote Control receiver when used

with Remote Control Kit (UXRC1).

8. Wi-Fi (Remote only): Not available.

9. Delay Off (Remote only): Press and hold

Delay Off to toggle Delay Off function.

327

541

Heat Sensor

Your hood is equipped with a HEAT SENSOR

thermostat. This thermostat is a device that will turn on

or speed up the blower if it senses excessive heat above

the cooking surface.

Ŷ,IEORZHULV2IILWWXUQVEORZHU2QWR0HGVSHHG

Ŷ,IEORZHULV2QDWDORZHUVSHHGVHWWLQJLWWXUQV

blower up to Med speed.

When the temperature level drops to normal, the blower

will return to its original setting.

Remote Control

6 49-80797-3

USING THE HOOD: Chef Connect

Chef Connect Operation Bluetooth

Connection

To pair with another device:

To start the pairing process on the hood, press and hold

the Chef Connect button for 3 seconds. The backlight

for the Low-Med-High-Light-Chef Connect buttons will

flash in that sequence until the hood is paired with the

range or other device. If the pairing is successful, all five

backlights (Low, Med, High, Light, Chef Connect) will

flash simultaneously three times and then turn off and

the Chef Connect indicator light will turn on.

It will time out after 2 minutes if the pairing is not

completed, after which the pairing sequence will need to

be restarted.

To cancel pairing:

To cancel the pairing, hold the Chef Connect button

down for 3 seconds and then turn off the hood.

Default Sync Settings:

The factory default setting for the light will be the

brightest.

The factory default setting for the fan sync will be OFF.

The user can change the Default Sync Settings by

pressing and holding the Low button for 3 seconds. This

will enter the Default Settings Mode. Once in this mode,

the backlights for all buttons (Low, Med, High, Light,

Chef Connect) will blink On/Off indefinitely and the fan

and light will switch to the current Default Sync Setting,

so the user knows what the current default value is.

At this time, set the light and fan to the desired default

levels. Once the user is satisfied with the selection, press

and hold the Off button for 3 seconds. This will exit this

mode. At that time the backlights will stop blinking and

the state of the fan and light will change back to their

prior state before entering the Default Settings Mode.

Chef Connect

49-80797-3 7

Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.

The metal filters trap grease during cooking.

The filter must ALWAYS be in place when the hood is in use. The grease filter is dishwasher-safe and should be

cleaned every month, depending on the usage of the hood.

Mesh Metal Grease Filter

To remove:

Press filter latch in and pull down.

To replace:

Insert the bottom of the filter tabs into the corresponding

holes. Press filter latch in and lift up into place. Release

the latch to lock it in place.

To clean:

Swish the filter in hot soapy water and rinse in clean

water or wash it in the dishwasher. Do not use abrasive

cleansers.

NOTE: Some discoloration of the filters may occur in the

dishwasher.

Charcoal Filter (for recirculation installation only)

NOTE: DO NOT rinse, or put charcoal filter in an

automatic dishwasher.

The charcoal filter cannot be cleaned. It must be

replaced. It is recommended that the charcoal filter

be replaced every 6 months or if it is noticeably dirty

or discolored.

Order Charcoal Filter UXCF91 (not included)

To inquire about purchasing replacement charcoal filters

or to find the location of a dealer nearest you, please call

our toll-free number:

National Parts Center 800.626.2002

To Install

1. Remove the grease filters. See Filters section.

2. Install the charcoal filter mounts to either side of the

motor using three screws per side.

3. Insert the tab on the charcoal filter into the triangular

slot on the mount.

4. Clip the charcoal filter in until it is locked

5. Repeat with second filter on the other side of the

motor.

6. Reattach the metal filters. See Filters section.

To Remove

1. Remove grease filters-See Filters section

2. Unclip the charcoal filter by pressing the release clip.

3. Carefully remove charcoal filter from tab.

Filters

CARE AND CLEANING: Filters

Charcoal

Filter Mount

8 49-80797-3

Lights

CAUTION

Allow lights to cool before touching.

1. Before attempting to replace the lights, make sure that

the light switch is turned off.

2. Rotate light counterclockwise to unlock and pull out.

Wearing latex gloves may offer a better grip.

3. Replace with new light of same type, making sure

pins are inserted properly into the sockets of the lamp

holder and turn clockwise to lock.

All lamps need to be GU10 compatible.

Surfaces

CARE AND CLEANING: Surfaces / Lights

Rotate the lamp until the

pins are located in narrow

neck of the socket to lock.

Lamp

Holder

Stainless Steel Surfaces (on some models)

Do not use a steel wool pad; it will scratch the

surface.

To clean the stainless steel surface, use warm sudsy

water or a stainless steel cleaner or polish. Always wipe

the surface in the direction of the brush line. Follow

the cleaner instructions for cleaning the stainless steel

surface. Cleaners with oxalic acid such as Bar Keepers

Friend Soft Cleanser™ will

remove surface rust, tarnish, and

small blemishes. To receive a

coupon for a trial sample of Bar

Keepers Friend Soft Cleanser™

follow the link below or scan the

QR Code.

barkeepersfriend.com/ge

Use only a liquid cleanser free of grit and rub in the

direction of the brush lines with a damp soft sponge.

To inquire about purchasing stainless steel appliance

cleaner or polish, or to find the location of a dealer

nearest you, please call our toll-free number:

National Parts Center

800.626.2002

GEApplianceparts.com

49-80797-3 9

Installation

Instructions

“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)

or visit our website at: GEAppliances.com”

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT — Save these

instructions for local inspector’s use.

IMPORTANT — Observe all governing

codes and ordinances.

Note to Installer – Be sure to leave these

instructions with the Consumer.

Note to Consumer – Keep these instructions for

future reference.

Skill level – Installation of this vent hood requires

basic mechanical and electrical skills.

Completion time – Approximately 1 to 3 hours

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is not

covered under the Warranty.

FOR YOUR SAFETY

WARNING

Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag,

to the service panel.

CAUTION

Due to the weight and size of

these vent hoods and to reduce the risk of personal

injury or damage to the product, TWO PEOPLE

ARE REQUIRED FOR PROPER INSTALLATION.

WARNING

Disconnect all electrical power

at the main circuit breaker or fuse box before

installing.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with

all applicable codes and standards, including

fire-rated construction.

B. Sufficient air is needed for proper combustion

and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment

manufacturer’s guidelines and safety standards

such as those published by the National Fire

Protection Association (NFPA), the American

Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE) and the local

code authorities.

C. When cutting or drilling into wall or ceiling, do

not damage electrical wiring and other hidden

utilities.

D. Ducted fans must always be vented to the

outdoors.

E. Turn off breaker to adjacent rooms while

working.

WARNING

TO REDUCE THE RISK OF FIRE,

USE ONLY METAL DUCT WORK.

Custom Insert Hood

UVC7300

10 49-80797-3

Installation Preparation

INSTALLATION CLEARANCES

This vent hood must be installed between the 24"

required minimum and 36" recommended maximum

above the cooking surface.

Ŷ$OZD\VUHIHUWRWKHFRRNWRSRUUDQJHLQVWDOODWLRQ

instructions for product-specific clearances.

NOTE: Installation height should be measured

from the cooking surface to the bottom edge of the

cabinet surface.

NOTE: UL requires any combustible surface to be a

minimum of 30" above the cooking surface.

Ŷ7KHFXVWRPFDELQHWLQWHUQDOKHLJKWPXVWEH

16-5/8" minimum for vertical venting, 27-1/8" for

recirculation. If liner is used, the custom cabinet

internal height must be 20-5/8" minimum for

vertical venting, 31-1/8" for recirculation.

Ŷ7KLVKRRGFDQEHYHQWHGWRWKHRXWGRRUVRULW

can be installed for recirculating operation. For

recirculating operation, refer to Recirculating

Installation Planning.

Ŷ7KLVKRRGPD\EHPRXQWHGRQWRDFDELQHWRU

installed over an island.

NOTE: The exhaust duct on the hood is closer to

the rear of the hood. It is important to plan for the

alignment to the connection point of the hood.

CABINET PREPARATION

Liner (Optional) (UXHL30 or UXHL36)

PRODUCT DIMENSIONS

INSTALLATION PREPARATION

28-7/16" or

34-7/16"

19-9/16"

10-1/4"

17-1/4"

1" 1"

9-5/8"

FRONT VIEW

20-5/8"

10-3/16"

11-1/8"20-7/16"

12"

4-1/4"

6-15/16"

9-5/8"

3-1/8"

1-15/16"

3" 1"

SIDE VIEW

9-5/8"

31-1/8"

4-3/4"

Liner is used

*24" Minimum required

*36" Maximum recommended

Typically 36"

20-5/8" min.

9-5/8"

Liner is used

49-80797-3 11

Installation Preparation

PLAN THE INSTALLATION

CAUTION

To reduce risk of fire and to

properly exhaust air, be sure to duct the air

outside – Do not vent exhaust air into spaces

within walls or ceilings or into attics, crawl

spaces, or garages.

WARNING

PERSONAL INJURY HAZARD

It is recommended that 2 people are used to

install the range hood. Failure to properly

lift rangehood could result in damage to the

product or personal injury.

NOTE: This rangehood can be installed as either

ducted or recirculation. In a ducted application,

this rangehood can be vented through the wall

or ceiling. When installed for recirculation, the

rangehood vents back into the room.

REMOVE THE PACKAGING

CAUTION

Wear gloves to protect against

sharp edges.

Ŷ Remove the hardware bag, literature package

and other boxed parts.

Ŷ Remove and properly discard the protective

plastic wrapping and other packaging materials.

INSTALLATION PREPARATION

TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED)

Pencil and tape measure

Step ladder

Phillips and flat-blade

screwdrivers

Level

Safety glasses

8" ducting and

caps as needed

Aluminized

duct tape

Electric drill and

appropriate bits

Gloves

Flashlight

Needle-nose pliers

Tin snips

Wire cutter/

stripper

Strain relief for

junction box

UL listed wire nuts

PARTS PROVIDED

Locate the parts packed with the hood.

NOTE: The hardware bag may contain extra pieces

to accommodate a variety of installation methods

for various models.

Damper

Assembly

Hardware Bag

Hood

Phillips Head

Wood Screws

3/16" x 1-1/2"

(QTY: 4)

Phillips Head

Wood Screws

3/16" x 1"

(QTY: 8)

Philips Head

Machine Screw

1/8" X 3/8"

(QTY: 16)

Phillips Head

Wood Screws

1/8" X 3/8" (QTY: 4)

12 49-80797-3

Installation Preparation

INSTALLATION PREPARATION

ADVANCE PLANNING

Duct Install Planning

Ŷ7KLVKRRGLVGHVLJQHGWREHYHQWHGYHUWLFDOO\

through the ceiling. Use a 8" round duct. Use

locally supplied elbows to vent horizontally

through the rear wall. An 8" duct is required for

optimal performance but a minimum of 6" duct

can be used to ensure consistent performance.

Ŷ8VHPHWDOGXFWZRUNRQO\

Ŷ'HWHUPLQHWKHH[DFWORFDWLRQRIWKHYHQWKRRG

ŶPlan the route for venting exhaust to the outdoors.

To maximize the ventilation performance of the

vent system:

1. Minimize the duct run length and number of

transitions and elbows.

2. Maintain a constant duct size.

3. Seal all joints with duct tape to prevent any leaks.

NOTE: Flexible vent is not recommended. Flexible

vent creates back pressure and air turbulence that

greatly reduces performance.

Ŷ0D[LPXPHTXLYDOHQWGXFWOHQJWKIRU&)0

150 foot for vent hoods.

Ŷ,QVWDOODZDOOFDSRUURRIFDSZLWKGDPSHUDWWKH

exterior opening. Purchase the wall or roof cap and

any transition and length of duct needed in advance.

ŶWhen applicable, install any makeup (replacement)

air system in accordance with local building

code requirements. Visit GEAppliances.com for

available makeup air solutions.

Vent system can terminate either through the roof

RUWKHZDOO7RYHQWWKURXJKDZDOOD๦HOERZLV

needed and installed immediately above the hood.

Wall and Ceiling Framing for Adequate Support

This vent hood is heavy and the cabinet

structure needs to support the weight of the

loaded insert sleeve. Adequate structural support

must be provided in all types of installations.

Ŷ Installation will be easier if the vent hood is

installed before the cooktop is installed.

Roof Cap

Round Duct

Wall Cap

Add Insulation

and/or Caulk

Add Insulation

and/or Caulk

Cabinet

Add tape to joint

Hood

RECIRCULATION INSTALL PLANNING

This hood may be installed in recirculation mode.

The charcoal filter (not included) is necessary for

recirculation installation.

ADVANCE PLANNING (CONT.)

Custom Cabinet Frame Planning

ŶThe custom canopy or cabinet should have a

rectangular hole to accommodate the custom

hood insert by itself. This hole is the same

size for both a wall installation and an island

installation. Ensure parallelism and levelness of

the cabinet so that it doesn't affect flushness of

the hood with the cabinet.

19-7/16"

Front of hole

must be 3"

minimum from

cabinet front

Back of hole

must be 1"

minimum from

back wall

10-3/16"

49-80797-3 13

INSTALLATION PREPARATION

Installation Preparation

PREPARE FOR CABINET

INSTALLATION

NOTE: This bracket must be removed prior to

installation. Remove 2 back (rear) and 2 bottom

screws per illustration bellow.

1. Securely press the damper on top of the exhaust

opening. Check that the damper opens freely.

Attach damper to hood using screws (B) provided.

2. The hood should be centered left to right over

the cooktop.

3. Remove and properly discard the protective

plastic wrapping from the hood.

4. The back surface of the hood must be 1"

minimum from the back wall. The front surface

of the hood must be 3" minimum from the front

custom cabinet panel.

5. The custom cabinet should provide for

removal of panels to provide access to the

electrical wiring and to the ducting and its

connections to the hood in case of any need

for servicing or other reasons.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING

FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before

beginning installation.

Do not use an extension cord or adapter plug with

this appliance. Follow National Electrical Codes or

prevailing local codes and ordinances.

Electrical supply

These vent hoods must be supplied with 120V,

60Hz, and connected to an individual, properly

grounded branch circuit, and protected by a 15 or

20 amp circuit breaker or time delay fuse.

ŶWiring must be 2 wire with ground.

Ŷ If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

Ŷ Route house wiring as close to the installation

location as possible in the ceiling or wall.

Ŷ Connect the wiring to the house wiring in

accordance with local codes.

Grounding instructions

The grounding conductor must be connected to

a ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

WARNING

The improper connection of the

equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician

or service representative if you are in doubt whether

the appliance is properly grounded.

PREPARE HOUSE ELECTRICAL

WIRING

The custom cabinet must allow spacing for house

wiring to reach junction box located in diagram

below. If unit is installed over an island, the wiring

must come from ceiling. If power cord is needed,

accessory is available.

7-5/8"

12"

Electrical

Area

2-13/16"

14 49-80797-3

Installation

INSTALLATION

STEP 1

INSTALL HOOD LINER

(If Used)

1. The rectangular opening in framing or custom

cabinet must be sized for the liner outside and

inside dimensions. Refer to Product Dimensions

section.

2. Secure the liner to the cabinet with 4 wood

screws (A) or (D) as needed.

STEP 2

INSTALL THE HOOD

1. Confirm the damper is in place in the hood

exhaust opening.

2. Insert the hood into the cabinet opening.

STEP 2

INSTALL THE HOOD (Cont.)

3. Fasten with 8 screws (A or L), 4 in the back

and 2 on each side. It is recommended to start

with one corner and fasten screws diagonally to

ensure unit flushness with cabinet.

If the liner is used, fasten 12 machine screws

(B), 4 in the back, 4 in the front, and 2 on each

side. The front 4 screw holes are accessed by

removing the light panel assembly. The light

panel assembly is removed by removing the

two screws on both ends of the panel.

4. Once the hood is in place, seal the duct to the

hood with duct tape (Do not use screws).

49-80797-3 15

Installation

INSTALLATION

ELECTRICAL CONNECTION

1. Remove the electrical junction box cover.

2. Remove the electrical box knockout.

3. Feed the Power Supply Cable through the hole

and secure with a strain relief.

4. Attach the white lead of the power supply (A) to

the white lead of the range hood (D) with a wire

nut. Attach the black lead of the power supply (B)

to the black lead of the range hood (C) with a wire

nut. Connect the house ground wire under the

green grounding screw (E).

5. Reattach the electrical junction box cover.

House Wiring

Hood Wiring

Electrical Box

Knockout with

Strain Relief

16 49-80797-3

INSTALLATION

Installation

STEP 4

FINALIZE INSTALLATION

1. Insert filters, see the Filters section.

2. Check operation of the lights and blower.

3. Finish the custom cabinetry.

STEP 3

RECIRCULATION KIT (If Used)

1. Cut a hole into the soffit for the exhaust duct.

2. Install the vent grill over the exhaust duct.

3. Seal the duct joints with duct tape.

Visit GEAppliances.com to order the optional recirculation kit.

Hood Center Line

Soffit Cutout

90° Angle Boot

8” to 8” ducting

Filters

6-15/16"

9-5/8"

49-80797-3 17

Troubleshooting tips ... Before you call for service

Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem Possible Cause What To Do

Fan/Light does not

operate when button is

turned ON

A house fuse may be blown or a circuit

breaker tripped.

Replace fuse or reset circuit breaker.

Loud or abnormal

airflow noise

Wrong duct size used in installation. This hood requires 8” ducting to perform optimally.

Using smaller duct pipe will cause reduced venting.

Minimize the duct run length and number of transitions

and elbows. GE Appliances service technicians cannot

correct this issue if installed improperly.

Fan fails to circulate

air or moves air slower

than normal and/or

fan is making loud or

abnormal airflow noise

Obstructions in duct work. Make sure nothing is blocking the vent. Make sure

your wall or roof cap has a blade or door.

Damper blade on wall or roof cap may

not be open.

Make sure damper swings freely. Damper blades may

flip over and will not fully open when this happens.

Adjust to original position.

Metal grease filter and charcoal filter (if

present) may be dirty.

Clean the metal grease filter and replace charcoal filter

(if present). See Care and Cleaning of the Vent Hood.

Insufficient makeup (replacement) air Sufficient makeup (replacement) air is required for

exhausting appliances to operate to rating. Check with

local building codes, which may require or strongly

advise the use of makeup air. Visit GEAppliances.com

for available makeup air solutions.

Early light failure Light wattage is too high. Replace with correct wattage.

Fan keeps going off

and on

The motor is probably overheating and

turning itself off. This can be harmful to

the motor.

Check to be sure the filters are clean. If off and on

cycling continues, call for service.

Lights not functioning Wrong bulbs are used. Must use GU10

compatible dimmable bulbs.

Visit GEAppliances.com for replacement bulbs.

TROUBLESHOOTING TIPS

18 49-80797-3

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

GEAppliances.com

All warranty service is provided by our Factory Service Centers, or an authorized Customer Care

technician. To

schedule service online, visit us at GEAppliances.com/service_and_support/, or call GE Appliances at 800.GE.CARES

(800.432.2737). Please have your serial number and your model number available when calling for service.

Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE Appliances factory

service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its

products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be

sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.

What GE Appliances will not cover:

Ŷ Service trips to your home to teach you how to use

the product.

Ŷ ,PSURSHULQVWDOODWLRQGHOLYHU\RUPDLQWHQDQFH

Ŷ )DLOXUHRIWKHSURGXFWLILWLVDEXVHGPLVXVHG

modified, or used for other than the intended purpose

or used commercially.

Ŷ 5HSODFHPHQWRIKRXVHIXVHVRUUHVHWWLQJRIFLUFXLW

breakers.

Ŷ 'DPDJHWRWKHSURGXFWFDXVHGE\DFFLGHQWILUH

floods, or acts of God.

Ŷ 'DPDJHWRILQLVKVXFKDVVXUIDFHUXVWWDUQLVKRU

small blemishes not reported within 48 hours of

delivery.

Ŷ ,QFLGHQWDORUFRQVHTXHQWLDOGDPDJHFDXVHGE\

possible defects with this appliance.

Ŷ 'DPDJHFDXVHGDIWHUGHOLYHU\

Ŷ 3URGXFWQRWDFFHVVLEOHWRSURYLGHUHTXLUHGVHUYLFH

Ŷ 6HUYLFHWRUHSDLURUUHSODFHOLJKWEXOEVH[FHSWIRU/('

lamps.

LIMITED WARRANTY

GE Appliances Vented Range Hood Limited Warranty

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,

including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or

the shortest period allowed by law.

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for

home use within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer

is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized

GE Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service

calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: GE Appliances, a Haier company

Louisville, KY 40225

Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are

available while your warranty is still in effect. You can purchase it online anytime at

GEAppliances.com/extended-warranty

or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.

For the period of GE Appliances will replace

One year

From the date

of the original

purchase

Any part of the cooking product which fails due to a defect in materials or workmanship.

During this limited one-year warranty, GE Appliances will provide, free of charge, all labor

and related service costs to replace the defective part.

49-80797-3 19

ACCESSORIES

Looking For Something More?

GE Appliances offers a variety of accessories to

improve your cooking and maintenance experiences!

Refer to the Consumer Support page for phone numbers

and website information.

The following products and more are available:

Accessories

Parts

Power Cord Kit

Recirculation Kit

Charcoal Filter

Hood Liner

Remote Control

Cleaning Supplies

CitruShine™ Stainless Steel Wipes

CERAMA BRYTE

Stainless Steel Appliance Cleaner

Bar Keepers Friend Soft Cleanser™

20 49-80797-3

Consumer Support

CONSUMER SUPPORT

Printed in China

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support

services designed for your convenience. In the US: GEAppliances.com

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in

the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register

Schedule Service

Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at

your convenience any day of the year. In the US: GEAppliances.com/service

or call 800.432.2737 during normal business hours.

Extended Warranties

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your

warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your

warranty expires. In the US: GEAppliances.com/extended-warranty

or call 800.626.2224 during normal business hours.

Remote Connectivity

For assistance with wireless network connectivity (for models with remote enable),

visit our website at GEAppliances.com/connect or call 800.220.6899 in the US.

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the

details including your phone number, or write to:

In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225

GEAppliances.com/contact

Page is loading ...

GE Appliances UVC7300SLSS Owner's manual

Brand: GE Appliances

Model: UVC7300SLSS

Category: Cooker hoods

Type: Owner's manual

This manual is also suitable for

UVC7300SLSS

Download PDF

report

in other languages

español: GE Appliances UVC7300SLSS El manual del propietario

GE Appliances UVC7300SLSS Owner's manual

This manual is also suitable for

GE Appliances UVC7300SLSS Owner's manual

in other languages

Related papers

Other documents