Chauvet Professional STRIKE Reference guide

Category
Stroboscopes & disco lights
Type
Reference guide

This manual is also suitable for

1
EN
QUICK REFERENCE GUIDE
STRIKE Saber QRG Rev. 7
About This Guide
The STRIKE Saber Quick Reference Guide (QRG) has basic product information such as connection, mounting, menu
options, and DMX values. Download the User Manual from www.chauvetprofessional.com
for more details.
Disclaimer
The information and specifications contained in this QRG are subject to change without notice.
LIMITED WARRANTY
FOR WARRANTY REGISTRATION AND COMPLETE TERMS AND CONDITIONS PLEASE VISIT OUR WEBSITE.
For Customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration
.
For Customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and
Germany: www.chauvetlighting.eu/warranty-registration/
.
Chauvet warrants that this product shall be free from defects in material and workmanship under normal use, for the period
specified in and subject to the exclusions and limitations set forth in, the full limited warranty on our website. This warranty
extends only to the original purchaser of the product and is not transferable. To exercise rights under this warranty, you
must provide proof of purchase in the form of an original sales receipt from an authorized dealer that shows the product
name and date of purchase. THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. This warranty gives you
specific legal rights. You may also have other rights that vary from state to state and country to country. This warranty is
valid only in the United States, United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France,
Germany and Mexico. For warranty terms in other countries, please consult your local distributor.
Safety Notes
These Safety Notes include important information about installation, use, and maintenance.
DO NOT open this product. It contains no user-serviceable parts.
DO NOT look at the light source when the product is on.
CAUTION: Flashing light is known to trigger epileptic seizures. User must comply with local laws regarding
notification of strobe use.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the
product from power via breaker or by unplugging it.
CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid
ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow
product to fully acclimate to the surrounding environment before connecting it to power.
CAUTION: This product’s housing may be hot when lights are operating.
Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
DO NOT leave any flammable material within 50 cm of this product while operating or connected to power.
USE a safety cable when mounting this product overhead.
DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect
it. (IP20)
DO NOT operate this product if the housing, lenses, or cables appear damaged.
DO NOT connect this product to a dimmer or rheostat.
ONLY connect this product to a grounded and protected circuit.
ONLY use the hanging/mounting bracket to carry this product.
In the event of a serious operating problem, stop using immediately.
The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.
Contact
Outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact your distributor to request support or
return a product. Refer to Contact Us at the end of this QRG for contact information.
What is Included
STRIKE Saber
Neutrik® powerCON® power cord
Floor stand
Quick Reference Guide
EN
2
STRIKE Saber QRG Rev. 7
QUICK REFERENCE GUIDE
AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
Power Linking
You can link up to 9 STRIKE Saber products at 120 V, 16 products at 208 V, or 18 products at 230 V. Never exceed this
number. Power linking cords can be purchased separately.
AC Plug
Replacing the Fuse
1. Disconnect this product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.
DMX Linking
The STRIKE Saber will work with a DMX controller using a 5-pin DMX data connection. A DMX Primer is available from
www.chauvetprofessional.com
.
DMX Connection
The STRIKE Saber uses a 5-pin DMX data connection for its DMX personalities: 1Ch, 3Ch, 7Ch, 10Ch, 11Ch, 20Ch, and
27Ch. See the User Manual for information about connecting and configuring the product for DMX operation.
Master/Slave Connection
The STRIKE Saber uses the DMX data connection for its Master/Slave mode. See the User Manual for information about
connect and configure the product for master/slave operation.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. The STRIKE Saber supports RDM protocol that allows feedback to monitor changes to the
menu map options. Download the User Manual from www.chauvetprofessional.com
for more details.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow/Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
To eliminate wear and improve its lifespan, during periods of non-use completely disconnect the
product from power via breaker or by unplugging it.
3
EN
QUICK REFERENCE GUIDE
STRIKE Saber QRG Rev. 7
Mounting
Before mounting this product, read the Safety Notes. Use at least one mounting point per product. Make sure the
mounting clamps are capable of supporting the weight of the product. For our CHAUVET Professional line of mounting
clamps, go to http://trusst.com/products
.
Floor Stand
The STRIKE Saber comes with a Floor Stand which can be installed with the included screws.
Mounting Diagram
Safety cable
Mounting clamp
Secure the safety
cable using the
passageway on
the back of the
product
Overhead Mounting
Floor Stand Installation
Insert included screws (x4)
EN
4
STRIKE Saber QRG Rev. 7
QUICK REFERENCE GUIDE
Control Panel Description
Menu Map
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value into the selected function
<UP> Navigates upwards through the menu list and increases the numeric value when in a function
<DOWN> Navigates downwards through the menu list and decreases the numeric value when in a function
Main Level Programming Levels Description
DMX Address 001–512
Selects DMX address (highest channel restricted to
personality chosen)
DMX
Personality
1Ch 1-channel: dimmer
3Ch 3-channel: dimmer, strobe, red shift
7Ch
7-channel: 16-bit dimmer, strobe, auto programs, auto
speed, red shift, dimmer speed
10Ch 10-channel: 10-cell dimmer
11Ch 11-channel: 10-cell dimmer, red shift
20Ch 20-channel: 10-cell 16-bit dimmer
27Ch
27-channel: 10-cell 16-bit dimmer, strobe, auto programs,
auto speed, red shift, dimmer speed
Red Shift
On
Turns on or off Red Shift (Amber LEDs imitate lamp when
dimming
Off
Static
Fixed Color
Amber Amber
White White
Amber&White Amber and white
Manual
Color Mixer
Amber
0–255
Combine amber and white to make a custom color
temperature
White
Auto Show Auto 1–6 1–100 Selects automatic programs and program speed
Master/Slave
Master DMX mode (Master)
Slave Slave mode
Dimmer Mode
Off Linear dimmer
Dimmer 1–3 Dimming curves Dimmer 1 (fast) to Dimmer 3 (slow)
LED
Frequency
600Hz
Sets the PWM frequency
1200Hz
2000Hz
4000Hz
6000Hz
25KHz
Back Light
10S Turns off display backlight after 10 seconds of inactivity
30S Turns off display backlight after 30 seconds of inactivity
2min Turns off display backlight after 2 minutes of inactivity
Always On Display backlight always on
Information
Fixture
Hours
<_ _ _ _H> Shows total hours the product has been powered on
Version <V_._> Shows current firmware version
UID <_ _ _ _ _ _ _ _ _ _ _ _> Shows product UID
Reset Factory
No
Resets the product to factory default settings
Yes
5
EN
QUICK REFERENCE GUIDE
STRIKE Saber QRG Rev. 7
DMX Values
27Ch
Channel Function Value Percent/Setting
1 Dimmer 000
255 0–100%
2 Fine Dimmer 000
255 0–100%
3 Dimmer 1 000
255 0–100%
4 Fine Dimmer 1 000
255 0–100%
5 Dimmer 2 000
255 0–100%
6 Fine Dimmer 2 000
255 0–100%
7 Dimmer 3 000
255 0–100%
8 Fine Dimmer 3 000
255 0–100%
9 Dimmer 4 000
255 0–100%
10 Fine Dimmer 4 000
255 0–100%
11 Dimmer 5 000
255 0–100%
12 Fine Dimmer 5 000
255 0–100%
13 Dimmer 6 000
255 0–100%
14 Fine Dimmer 6 000
255 0–100%
15 Dimmer 7 000
255 0–100%
16 Fine Dimmer 7 000
255 0–100%
17 Dimmer 8 000
255 0–100%
18 Fine Dimmer 8 000
255 0–100%
19 Dimmer 9 000
255 0–100%
20 Fine Dimmer 9 000
255 0–100%
21 Dimmer 10 000
255 0–100%
22 Fine Dimmer 10 000
255 0–100%
23 Strobe
000
010 No function
011
125 Strobe, slow to fast
126
255 Random strobe
24 Auto Programs
000
010 No function
011
032 Auto program 1
033
076 Auto program 2
077
120 Auto program 3
121
164 Auto program 4
165
208 Auto program 5
209
255 Auto program 6
25 Auto Speed 000
255 Auto speed, slow to fast
26 Red Shift
000 Red shift on, amber channels disabled
001
255 Red shift off, amber channels enabled
27 Dimmer Speed Mode*
000
051 Preset dimmer speed from display menu
052
101 Dimmer speed mode off
102
152 Dimmer speed mode 1 (fastest)
153
203 Dimmer speed mode 2
204
255 Dimmer speed mode 3 (slowest)
*Hold desired dimmer speed value for 3 seconds, then release. This changes the dimmer speed
setting in the menu.
EN
6
STRIKE Saber QRG Rev. 7
QUICK REFERENCE GUIDE
20Ch
11Ch
10Ch
Channel Function Value Percent/Setting
1 Dimmer 1 000
255 0–100%
2 Fine Dimmer 1 000
255 0–100%
3 Dimmer 2 000
255 0–100%
4 Fine Dimmer 2 000
255 0–100%
5 Dimmer 3 000
255 0–100%
6 Fine Dimmer 3 000
255 0–100%
7 Dimmer 4 000
255 0–100%
8 Fine Dimmer 4 000
255 0–100%
9 Dimmer 5 000
255 0–100%
10 Fine Dimmer 5 000
255 0–100%
11 Dimmer 6 000
255 0–100%
12 Fine Dimmer 6 000
255 0–100%
13 Dimmer 7 000
255 0–100%
14 Fine Dimmer 7 000
255 0–100%
15 Dimmer 8 000
255 0–100%
16 Fine Dimmer 8 000
255 0–100%
17 Dimmer 9 000
255 0–100%
18 Fine Dimmer 9 000
255 0–100%
19 Dimmer 10 000
255 0–100%
20 Fine Dimmer 10 000
255 0–100%
Channel Function Value Percent/Setting
1 Dimmer 1 000
255 0–100%
2 Dimmer 2 000
255 0–100%
3 Dimmer 3 000
255 0–100%
4 Dimmer 4 000
255 0–100%
5 Dimmer 5 000
255 0–100%
6 Dimmer 6 000
255 0–100%
7 Dimmer 7 000
255 0–100%
8 Dimmer 8 000
255 0–100%
9 Dimmer 9 000
255 0–100%
10 Dimmer 10 000
255 0–100%
11 Red Shift
000 Red shift on, amber channel disabled
001
050 Red shift off, amber channel enabled
051
100 Use Warm White LEDs ONLY
101
255 Use Amber LEDs ONLY
Channel Function Value Percent/Setting
1 Dimmer 1 000
255 0–100%
2 Dimmer 2 000
255 0–100%
3 Dimmer 3 000
255 0–100%
4 Dimmer 4 000
255 0–100%
5 Dimmer 5 000
255 0–100%
6 Dimmer 6 000
255 0–100%
7 Dimmer 7 000
255 0–100%
8 Dimmer 8 000
255 0–100%
9 Dimmer 9 000
255 0–100%
10 Dimmer 10 000
255 0–100%
7
EN
QUICK REFERENCE GUIDE
STRIKE Saber QRG Rev. 7
7Ch
3Ch
1Ch
Channel Function Value Percent/Setting
1 Dimmer 000
255 0–100%
2 Fine Dimmer 000
255 0–100%
3Strobe
000
010 No function
011
125 Strobe, slow to fast
126
255 Random strobe
4 Auto Programs
000
010 No function
011
032 Auto program 1
033
076 Auto program 2
077
120 Auto program 3
121
164 Auto program 4
165
208 Auto program 5
209
255 Auto program 6
5Auto Speed 000
255 Auto speed, slow to fast
6Red Shift
000 Red shift on, amber channel disabled
001
255 Red shift off, amber channel enabled
7 Dimmer Speed Mode*
000
051 Preset dimmer speed from display menu
052
101 Dimmer speed mode off
102
152 Dimmer speed mode 1 (fastest)
153
203 Dimmer speed mode 2
204
255 Dimmer speed mode 3 (slowest)
*Hold desired dimmer speed value for 3 seconds, then release. This changes the dimmer speed
setting in the menu.
Channel Function Value Percent/Setting
1 Dimmer 000
255 0–100%
2Strobe
000
010 No function
011
125 Strobe, slow to fast
126
255 Random strobe
3Red Shift
000 Red shift on, amber channel disabled
001
255 Red shift off, amber channel enabled
Channel Function Value Percent/Setting
1 Dimmer 000
255 0–100%
Multi-Language
QUICK REFERENCE GUIDE
36
STRIKE Saber QRG Rev. 7
Contact Us
Visit the applicable website above to verify our contact information and instructions to request support. Outside the
U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the dealer of record.
General Information Technical Support
Chauvet World Headquarters
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: [email protected]
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetprofessional.com
Chauvet Europe Ltd
Address: Unit 1C Email: UKtech@chauvetlighting.eu
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetprofessional.eu
NG16 6NT
Voice: +44 (0) 1773 511115
Fax: +44 (0) 1773 511110
Chauvet Europe BVBA
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetprofessional.eu
Voice: +32 9 388 93 97
Chauvet France
Address: 3, Rue Ampère
91380 Chilly-Mazarin
Email: FRtech@chauvetlighting.fr
France Website: www.chauvetprofessional.eu
Voice: +33 1 78 85 33 59
Chauvet Germany
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Email: DEtech@chauvetlighting.de
Germany Website: www.chauvetprofessional.eu
Voice: +49 421 62 60 20
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetprofessional.mx
Lerma, Edo. de México, CP 52000
Voice: +52 (728) 690-2010
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

Chauvet Professional STRIKE Reference guide

Category
Stroboscopes & disco lights
Type
Reference guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI