GE GNSL05CBL Owner's manual

Brand: GE

Model: GNSL05CBL

Type: Owner's manual

This manual is also suitable for

GEAppliances.com

Safety Instructions ........... 2

Operating Instructions

Specification Guidelines ....... 3

Using the System ............ 4

Installation Instructions ...5-11

Battery Pack Installation ....... 8

Faucet Installation .......... 7, 8

Feed V(ater Supply ........... 6

Filter Cartridge Installation

or Flush Procedure ....... 10, 11

Important Recommendations ...5

Replacement ............ 10, 11

Step-by-Step Instructions ..... 7-9

Tools/Mamrials Required ...... 5

Tubing Connections .......... 9

_4'all Mounting ............... 9

Troubleshooting Tips ....... 12

Consumer Support

Consumer Support .......... 16

Parts List/Catalog ........ 13, 14

_a'arranty .................. 15

62MS'V25CBL

(;NSV3OC-WW

(;,MgV30CCC

CNSLOSCBL (rev. 2)

(;NISISCBL (rev. 2)

GNSL05CBL(rev. 2) and SNIS15CBL (rev. 2)

are Tested andCertified by NSFInternational

against ANSI/NSF Standard 42for the reduction

of Particulate Class I, Chlorine, and Taste/Odor

and Standard 53for the reduction of Lead, Cyst,

Turbidity, Asbestos, Mercury, Atrazine and

Lndane.

SNSV25CBL,GNSV30CWWand SNSV30CCC

are Tested and Certified by NSFInternational

against ANSI/NSF Standard 42for the reduction

of Particulate ClassI, Chlorine, and Taste/Odor

and Standard 53for the reduction of Lead, Cyst,

Mercury, Turbidity, Asbestos and VOC.

Write the model and serial numbers here:

Model #

Serial #

_m can find them on the sump bracket.

215C1001P019-3

7239707

49-50057-3 05-02 JR

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

A WARNING; Foryoursafety,theinformationinthismanualmustbefollowedtominimizethe

risk of property damage or personal injury.

SAFETYPRECAUTIONS

• Check with }our local public works departn]ent

fi>r I)ltunl)ing, codes. Ybu must fi>llow these

guidelines as )ou install the _\'ater Filtration

S_SteIll,

• Use the _Ahter Filtration system on a potable,

sale-to<lfink, home COLDwater supply only.

The filter cartridges x_illnot purit}' the x_zJte_;

(:,rmake it sale to drink.

• Do not use on a hot x_zJter supply (l ()()°F max.).

A WARNING: D...,use with water that

is microbiologically unsate or of unknown

qt_dity without adequate disintection befiwe

or after the system. Systems certified tot cyst

x'educfion may be used on disinfected water

that may contain filterable c}'sts.

PROPERINSTALLATION

This Water Filtration system must be properly instated and located in accordance with the

Installation Instructions before # is used.

• Install or store where it will not be exposed to

temperatures below fl'eezing or exposed to any

type of weather _,\hter fl'eezing in the system

will damage it. Do not attempt to treat water

over IO0°E

a, WARNING:Discard all unused

and I)ackagin°, _ material atter installation.

Small parts remaining after installation

could be a choke hazard.

IlYour Water Filtration system will withstand up to

125 pounds per square inch (psi) water pressure.

If your house water supply pressure is higher than

11)O psi, install a pressure reducing \:dve befi)re

installing the }\hter Filtration system.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Specifications guidelines, www.GEAppliances.com

Many bad tastes and/or odox_ are renloved fl'oln water using acti;'ated carbon filter cartridges. They are

most often used to remove a chlorine taste and odin: They can also reduce other undesirable elements ti'om

drinking water sui)plies, such as o_ganic chemical contaminants and lead.

/VOTE'.Small amotmts (ff hydrogen sulfide (noticeable as "rotten egg" odor) may be reduced by taste and

odor filte_ tot a short time, but the carbon media is quickly exhausted. Other water conditioning

equipment is usually required tin" the continuous treatment of hydrogen sulfide.

The Water Filtrationsystem uses two filter cartridges.

For Model GNIS15CBL

(rev.2)

FXUI£; (rev. 2) Filter

(600-Galhm Capadty)

Fther - \_lfim with

yellow end caps

• Reduces dirt, rust and

sediment

• Reduces tmpleasant

tastes and odoiN

" Reduces Chlorine:

%_sm and Odor

" Reduces i,ead

• Reduces _&sbestos

" Reduces filterable cysts

(such as

cryptosporidium

and giardia)

" Reduces iJm-lane

(a pesticide)

" Reduces Tm'biditv

• Reduces Mercm'v

• Reduces Atrazine

" 0.5-1 micron nominal

particulate reduction

ForModel GNSLO5CBL

(rev.2)

FXSI,C (rev. 2) Filter Set

(600-Gallon Capadty)

Fdter I - White with no

end caps

Filter 11- \,_]fite with

yellow end caps

" Reduces dirt, rust and

sediment

• Reduces tmpleasant

tastes and o(lo_

" Reduces Chlorine:

Taste and Odor

) Reduces I,ead

• Reduces _&sbestos

" Reduces filmrable cysts

(such as

cryptosporidium

and giardia)

• Reduces i,indane

(a pesticide)

" Reduces Tm'biditv

" Reduces Mercury

" Reduces Atrazine

• 0.5-1 micron nominal

particulate reduction

ForModels GNSV25CBL

GNSV3OCWW and

GNSV30CCC

FXS_VC (rev. 2) Filter Set

(600-Gallon CapaciU')

Fdter I - White with

green end caps

Fdter II - Gray

• Reduces dirt, rust and

sedim ent

" Reduces tmpleasant

tastes and odoiN

" Reduces Chlorine:

Taste and Odor

" Reduces I,ead

" Reduces Asbestos

" Reduces filterable cysts

(such as

c_Tpt()sporidium

and giardia)

• Reduces Volatile

O_ganic Chemicals

(VO(:s)

" Reduces Mercury

" 0.5-1 micron absolute

particulate reduction

This system confimns to ANSI/NSF 42 and 53 fin" the specific perfimnance

claims as verified and sustained by test data.

Minlknum- MaximumSupplyWaterPressure- 40-125poundspersquareinch(psi)

Minlknum- Maxl_numSupplyWaterTemperature- 40°-100°F

Inlet- Outlet- 3/8" NPT,fittingsandtubingincluded

RatedServiceFlow- t_6gpm[GNSLO5CBL(re_2)andGNIS15CBL(re_2)]

0.6gpm(GNSV25CBL,GNSV3OCWWand GNSV30CCC)

Dependingonthetreatmentneededforaspecihcwatersupply,thewaterfiltrationsystem

canbecustoml#eduslhganycombinationoftheprecedingfiltercartridgesets.

About the water filtration system.

Using the Water Filtration System and About the Filter Cartridge

The countertop timcet dispenses filtered drinking water when opened.

It has a hand-operated, spring-loaded closed lever to prevent waste,

Ym can keep the timcet open bv pushing upward on the lever to lock it

against the timcet spout.

Filter Cartridge Life -Se',eral ",ariables detemfine how long the cartridges

will last in your Water Film_tion system. These include:

E_] How much water you use.

r-_'] How much sediment, taste and/or odor, lead, or other unwanted substance

is in the water

No matter which Water Filtration system you have, you should replace the

cartridges eve_T six months, when indicated bv the electronic indicator

light on the base. In extremely poor water supplies, you may notice the

return of the unwanted substance in vour water before the six months

are up. In this case the camidges should be replaced immediamly.

If the s):stem is also fin" lead or chemical contaminant removal, it is

MORE IMPORTANTto replace the cartridges at least every six months.

NOTE:If the water supply contains high aillotlnts of sediments, the carbon

filte_ may plug prematurely, reducing filtered water fl_)w to the system

timcet. Cartridge replacement is needed to restore flow.

Electronic Indicator Light(not available onall models) - Th eelectronic

indicator light on the base ot the timcet is a six-month timer that shows

w)u when to replace the filter cartridges. _,_]_en the battery pack is fi_t

installed, the indicator light will light briefly to show that the electronics

are operating. If this does not happen, the batteries may be installed

backwards or the lead wires are not connected.

_Mter about six months, the indicator light begins to flash. It is time to

replace the filter cartridges. X._qmn rel)lacin,*_ the filter cartridges, also

replace the batteries in the batte_, pack. Two __ batteries are required.

Dr_ _i@Fiitered water faucet

_ Lock

Open

Indicatorlight

InstallationInstructions.

Important Installation Recommendations

Read entire manual. Failure to follow all guides and rules could cause personal injury or proper_' damage.

• Checkwithyourlocalpublicworksdepartmentfor

plumbingcodes.Youmustfollowtheirguidesas

youinstalltheWaterFiltrationsystem.

• UsetheWaterFiltrationsystemonapotable,

safe-to-drink,homeCOLDwatersupplyonly.Thefilter

cartridgeswillnotpurifywaterormakeunsafewater

safetodrink.DONOToseonHOTwater(100°Fmax.).

• ProtecttheWaterFiltrationsystemandpipingfrom

freezing.Waterfreezingin thesystemwill damageit.

• YourWaterFiltrationsystemwillwithstandupto

125psi waterpressure,ff yourhousewatersupply

pressureishigherthan100psi duringtheday

(itmayreachhigherlevelsat night),installa

pressure-reducingvalvebeforethesystem.

_i WARNING: Do not use with water that is

microbiologically tmsate or of tmknown quality

without adequate disintection betore or alter

the system. These systems are certified tot cyst

reduction and may be used on disintected

water that may contain filterable cysts. The

water should be tested periodically to vefit}' that

the system is perfimning satisfi_ctofil> Small

parts remaining after the installation could be

a choke hazard. Discard satelv.

Toolsand Materials Required for Installation

• Slotted and Phillips screwdrivei_

• Plie_ and a(!iustablejawwrench

• Hand- or batte_Tq)owered drill and 1/4" bit

(saddle \:dve installation)

• Electric drill and drill bit to drill 1" - 1 1/4" hole

(type as required) if motmting hole is needed

tot [i_ucet

CAUTION: To avoid damaging the sink, consult

a qualified l)lumber or installer tot drilling

procedm'es. Special drill bits may be needed

tot porcelain or stainless steel.

Contents included with the product'.

• _'\_ter filter assembly, including mounting bracket

;:111(1 ScI'e_S

• Product IJteratm'e (Owner's Manual and

Installation Instructions, Product Data Sheet,

Owner Product Registration Card)

• _'\_ter supply/saddle \:dye

• Filtered water filucet tor sink or cotmtertop

motmting

• Electronic indicator fimcet base and batte_ T pack

(not a\;filable on all models)

• 3/8" tubing and fittings to make all needed

connections

• Sump wrench

Installation Overview

Locate the drinking water system on the cold water supply pipe, under

the kitchen and/or bathroom sink, to filter the cold drinking water.

Filtered _Tubing Insert

wa e.a.cet__.{

Ba.e pack.- t, ...-'" "%,

HotCold \ _ /_._ v-<_

Shutoffvalve/ . _ _/I]t---.]i

NOTE" 7-0change the filter I _\, mater i H

.' ' IRsert w_ '

cartndge yolmssttuToff "' "'''_ I I [

thewato_Anearbyshutoff . . hi I,Irill, ,I

valveis convenient.Most \. T,ib,,ig_ /lIIi _

sinksalreadyhaveshutoff FilierI !..,[

valveson fl?esupply pipes.

Dual Stage

Waterout

Mounting

screw(2)

FilterII

Nut_

Tubing_j_

Waterout

Mounting

screw(2/

Single Stage

InstallationInstructions.

Feed Water Supply

Check and comply with local plumbing codes as you plan; then instnll a cold feed water supply fitting. For new

l_ome instnllation using st;mdard phunbing fittings, see fiI_t two illustrations below. A _'pical installation for

existing homes using the saddle \_dve is shown ill third illustration below.

A. PREFERREDINSTALLATION

F_Tum off the cold water suppl):

F_ Comph,ing with phunbing codes, instnll a fitting on tile cold _ater pipe to adapt .'4/8" OD tubin , _ t_/ical

connection is shm_n ill illustrations at right (parts not included). Make sure a x_ater suppl)vahe is used.

water

Preferred water supply connection

(using compression fitting)

Watersupplyvalve

Insert(notincluded)

Ferrule

€

3/8" tubing to inlet

B. OPTIONAL HOME INSTALLATION Where codes permit

*For 1/2" ODor larger metal tubing only.

NOTE: Codesin the state of Massachusetts require installation by a licensed plumber and do not perm# the use of

the saddle valve. For installation, use plumbing code 248-CMR ofthe Commonwealth ofMassachusetts.

F_] Turn off the cold water supply and attnch saddle xalxe as shown ill illustration at d ,ht

._DANGERJTo protect yourself from serious injury or fataJ shock, use a battery-powered hmld drill only

to make the hole. DO NOT USEAN ELECTRICDRILL

F_ Close the _ater supply xalxe b) turning the handle clock_ise.

F_ Open the inain water supply ;al;e and se;eral house filucets to purge air fl'oln the s)steln. Close tilucet,s

when water i'[lns Sllloothlx: '

Optionalwatersupplyconnection(usingsaddlevalve)_

*For I/2" OD or larger metal tubing only.

Snugvalveinto

OVERTIGHTEN.

Nut(2) not J Predrill

requiredif holesin i_ 4 1/4"hole Seal makesurethe

clamparethreaded sealisin place

Clair

Somethreads

Tubin(

Tubinc

Rubbergasket Compressionnut

Use to connect the tubing

Step-by-stepinstallationinstructions.

Faucet Installation for Model GNIS15CBL (rev. 2) only

Be sure there is room underneath tile sink to make

tile needed connections. Select one of tile tollowing

places to install tile timcet:

_]N an existing sink spray attachment or soap

dispenser hole.

--IN a hole to be drilled in the sink top.

_]N a hole to be drilled in the countertop, next

to the sink.

Lever

NOTE:I,ooking at second illustration at right, be sure

tile fimcet base will fit fiat against tile surti_ce at tile

selected location so the gasket will seal.

_]If drilling is needed, make a ?/4" to 1" dia. hole.

Be sure touse the proper procedure for drilling

porcelain or stainless steel Special drill bits may

be needed.

Smallgasket

Faucet

stud

Base

ASSEMBLED

[]

Place small gz_sket, base and large gasket (in that

order) onto the fimcet stem. Next, place lock

x_nsher and hex nut onto timcet stud.

_] Insert washer into tubing ada )ter Securely

tighten to ti_ueet stud.

[_ Feed the length of .'4/8" OD tube fl'om the

bottom uI) through, tile mounting hole.

Connect to tile tubing adapter as shown in

second illust_tion, tightening tile compression

n/It securelv.

_] Remoxe tile short shipi)ing tube and insert

tile spout into tile timcet bod). Rotate spout

into place.

@ I,ower tile thucet assembly into place on tile

tmde_ide of tile mounting hole. Place tile

mounting bracket above the lock washe_:

}\]file holding the mounting bracket in place,

securely tighten the hex nut.

Sink

Large gasket

Lockwasher_

Hexnut_ I

Tubing_,

insert

_Mounting bracket

_ Tubingadapter

_[_'_'_ Compressionnut

Tubing

Compression

Tubingadapter

3/8" tubing,{I

to FilterIIoutlet}

Step-by-stepinstallationinstructions.

Electronic Faucet Installation (not available on all models)

Be sure there is room underneath the sink to make the needed

connections. Select one of the tk)ll()wing places to install the ti_ucet:

---IN an existing sink spray attachment or soap dispenser hole.

_]N a hole to be drilled in the sink top.

_]N a hole to be drilled in the countertop, next to the sink.

NOTEJi,ooking at fimrth illustration at right, be sure the timcet base

will fit flat against the suriilce at the selecmd location so the gasket will

seal. The base inav have to be angled sideways or diagonally.

_]If drilling is needed, make a 1" - 1 1/4" dia. hole. Be sure to use the

proper procedure fordrilling porcelain or stainlesssteel, Special drill

bits maybe needed,

[] i,ookino at tix_t illustration, insert a screw into the NON_SI,OTTED

base mounting hole. Turn a fiat nut a few turns onto the screw.

_] Posidon the base gasket oxer the mounting hole. Set the base on

the gasket, routing, the leadwire through, the mounting hole.

Holding the fiat nut under the sink with one finge_; tighten the

screw until just snug.

[_ Turn the remaining fiat nut a tew turns onto the other screw.

Posidon the screw in the slotted base motmdng hole and tighten

tmtil snug. Make sure the gasket posidon is properly aligned and

carefullytightenboth screws until the base is held fimflv in place.

Do not overtighten and break the base.

_] Assemble the top timcet base and hex nut onto the timcet stud

(third illustration). Tighten the nut until snug.

_] Insert tubing insert into tubing adapte_: Securely tighten to timcet

stud.

3 " )

_] Feed the length of,/8 O[ tubing fl'om the bottom up through

the timcet base. Connect to the tubing adapter as shown in tourth

illustration, tightening the compression nut securel>

_ Remoxe the short shipping tube and screw the spout into the

thucet body.

_ I,ower the flmcet assembly and lock into place on the faucet base.

Battery Pack Installation and Connection

_]n a dr) location, within reach of the electronic base 3' lead wire,

select a [)lace for the battex_' pack (see illustration on [)age 5).

The battery pack attaches to most sudi_ces, using the included

"stick)q)ack" Velcro T_Istrip.

]The battery pack tlses two size _A batteries. Check to be Stli'e they

are installed correctly. Then remoxe the paper backing

on the Velcro TMstrip and secure the pack in place.

[_] Fasten electronic base lead wire and battery pack connector

together.

Screw(2)

Faucet

base

Nut12}

TOPVIEW

Nut(2)_ Screw(2)

Faucetbase_ _ _4/.- 1" 11/4"dia.

\\ // !r,ou,,t n ho,e

Gasket---_-_ mo_::'tker_rop

Lever

_ Faucet

,_,_ Faucetstud

@%p2ucet

@_e--- Hexnut

-_ Tubinginsert

_ Tubingadapter

_ Compressionnut

Tubinginsert

3/8" tubing,(run

toFilter2 outlet)

Tubingadapter

Baseleadwireconnector,_ \ \

(to batten/pack} / \ \

Mounting Bracket to Cabinet Wall

The bracket can be used as a ten@late fin" marking the location of the mounting screx_s. _,\q_en detemfining the location of

the bracket, make sm'e )ou leave ] 1/2" to 2" of free area trader the sumps to allow fin" smnp remoxal and enough space on

either side to make the robing com_ections.

Tubing _._r _

connector

(inlet/

Sump-_}_

Filter I

FilterII

Dual Stage

Tubing

connector

{outlet)

Mounting

screws

_'-_ Sump

2-3/4" ]

Mounting -_

bracket

Tubingconnector..I_'_

(inlet)

Sump._,

Tubingconnector

_._ _utlet/

_'_ Mounting

screws

TubingConnections - Compression Style

_]Rtm the length of the 3/8" robing, c(nmected to the bottom of the

fimcet, to the filter system outlet (illtBtmtion aboxe). Allow enough

slack in the robing so that the refit can be easily returned.

V_ Measm'e and cut the end of the tubing square usim,,_ a shaq_ cutter

LmJ or knife. Remoxe any bm'_ (illustration A).

_] Inspect the end of the tubing, about 1 inch, to be sm'e there are no

impertections. It may be necessar) to cut the robing again.

[_ Slide plastic nut oxer the 3/8" robing.

_] Then slide plastic insert into 3/8" robing.

_] h_sert the plastic tubing all the way to the bottom of the elbow,

Tubing must be fully inserted to avoid leaks,

[_ Slide nut up to the elbow and thread on by hand tmfil fight.

_ Repeat the procedm'e to connect the tubing between the filter system

inlet and the water suppl)/saddle xalxe (illustration in the Installation

Overview section ) .

_]IMPORTANT. Be sure to check fin" leaks at all connections. Tighten as

needed.

IMPORTANE 24 hom_ after instnllation, check fin" an) slow leaks that

Ill;IX' OCC/II; Tighten connections ;is needed,

IMPORTANE If unit is not going to be put into use immediately

mrn off the water supply xalxe.

NOTE: A\oid instnlling the refit where the robing is pulled at a shaq) angle.

This bpe of instnllafion ram' cause the fittings to leak. If using tubing other

than what is supplied, be sm'e it is, hioho qualib'; exact size and rotmdness,

and has a Sillooth S/lI'l_ilCe,

Cuttubingsquare

t I

Endoftubingroundandsmooth,with nocuts,nicks

orflatspots(approximately1inch)

Tubing

EIb°w"_" ;i [

Nut,_,- [:3::_

..... J

Tubing

Nut

Head _- Insert

_-Sump

Aboutthe water filtrationsystem.

Filter Cartridge Installation or Replacement

CAUTION: Ne',er remo',e the sumps when water

i_ressure is in the _tei" Filtration svsteln.

[]Close the water supply/saddle valve to the filter.

(See illustration in the Installation Overview

section fin" locadon of the water supi)ly ",d',e.)

Open the filtered water fimcet.

_ RelnoXe the sumi), using the sum I) _i'ench tool

provided, from the filte_: head by rotating the

sum I) as shox_n in the belox_ illustration.

Be careflfl, the sum I) may be flfll of x_ater

Be sm'e to kee I) the large o-ring seal.

If v(,m are tel)lacing, a filter cartridge, remox e

_]and discard the used filter cartridge.

[_Be sm'e the inside of the sump is clean.

Thoroughly wash the inside of the sump

with hot, soap} water aim rinse.

[_ Remoxe the wrapper from the new filter

cartridge and insert the filter cartridge in the

sulni). Some cartlidges fit either way, while

others fit onl} one _say. ()bsec, e iimrkings on

the cartridge.

NOTEJThe _'ater Filtration svsteln InaV use two

different _'pes of filter cartlidges. Be Stli'e to

inst;dl theln cort'ecfl_,. Filter Icartrklge should

ah_avs be placed in the Filter I sump. Filter II

cartrklge should alx_a}s be placed in the FilterII

sunlp. See page 3 for a complete list of filter

i)ertimnance charactelistics.

Turnsumpwrenchtool

providedclockwiseto L.

removesulep

Sump

_ t--I _:_ _ Bracket

INLET_

Cartridge_ _% Head

Sumpl---_q II It I _4--._J.___..L_y::_TURNSUMP

TURNSUMP_ I_"-_] _ _I I

"ro.mow

ForModel GNIS15CBL

(rev.2)

FX/JI,C (rev. 2) Filter

(600-Gallon Capadty)

Filter - White with

vellow end caps

For Model GNSLO5CBL

(rev.2)

FXSI,C (rev. 2) Filter

Set

(600-Gallon Capacity)

Filter I - White with no

end caps

Filter I1 - White with

yellow end caps

ForModelsGNSV25CBL,

GNSV3OCWW&

GNSV30CCC

FXSVC (rev. 2) Filter Set

(600-Gallon Capacib' )

Filter I - X,\]fite with

green end caps

Filter II - Gray

_] I,ightl_ lubricate the o-ring seal in the smnp with clean fi)od-grade silicone grease (silicone grease is

a_ filable through (;E Parts and Services: 1_00-626-2002, Part Number: _\_S60X 10005). Be sm'e it is fitly

seated in its groove.

_Hold the smnp up to the filter head, aligning the center hole in the cartridge with the protrusion on

the bottom of the head. Failm'e to obtain proper aligmnent ma) cause damage to the filter and/or

filtration system, which will degrade filter perfinmance.

[]Being careflfl not to cros_thread, rotate the sump onto the filter head and tighten secm'ely by hand.

NOTE'. If the sump will not tighten up to the head or if you feel resistax_ce, you may have the cartridge

in upside down or misali_ed, Take the cartridge out and check for correct orientation or aJigmnent

mid reasseinble.

_ Repeat steps2 through 8 for the Filter II cartridge in the Filter II sump, if necessary.

_7_ Turn on the filtered water faucet. Then, slowly open the water suppl)/saddle _al_e and allow the

filter housing to fill.

_ Close the filtered water fimcet. Then, check fin" leaks between the sump and the head.

NOTE."If leaking, turn off the water supply and turn on the filtered water fimcet. Disassemble the filter

housing and check the o-ring for cuts, flat spots, etc., and sealing sui_li_ces fi)i" fin'eign InateI_ial. (:lean

the o-ring and lightly lubricate with clean silicone grease. Caretully press into the groove in the sump.

Reassemble and check tot leaks.

• I _ ...... I I ,.........

_ If you are re )lacin,* the batteries remoxe )re )erlx discard and install two new _M&_alkaline batteries in

the battery pack. Remoxing the batteries or momentaril_ disconnecting the lead wires resets the

six-month electronic time_: It is recommended that )ou change )ore" batteries at least once a _ea_:

_The filter cartridges contain acfixated carbon. X._hen new, ttli'n oIT the filtered water tilucet for ten

minutes to flush the s_stem.

]f yore" s) stem does not have an electronic monitm, place filter change label on sump, inside cabinet

doo_, or in another convenient location. _._rite in date of filter change fin" flmue reference. Filte_

should be changed exer) six months.

Flush Procedure

_._]/enever water of tmknown quali_' is passed through the GE _\'ater Filtration systeln, filter elelnents

should be discarded and the filtration system flushed.

Circumstances that may require flushing the system are:

• Boil-water ad\'ism_'.

• Flooding of the GE _._ater Filtration s_:stem.

• i,ong-tem/ non-use.

TheprocedureforflushingtheGEWaterFiltrationsystemis:

_]See Filter Cartridge Replacementsection and tbllow steps 1, 2, 3 and 4.

_ Next, reinstall the sumps (without the filter elements), turn water on and flush water through the

fimcet fin" one minute.

_] Then, turn water off, remo_e sumps, erupt' water out of sumps and install new filter elements.

[_ Follow steps 5-11 in the Filter Cartridge Replacementsection to complete.

Beforeyoucall forservice...

Troubleshooting -tips

Save time and money! Review the chart below

first and you may not need to call for service.

Problem Possible Causes What To Do

Water contains tiny New filter cm'tridges contain • Turn on the filtered water timcet and allow these

black particles activated carbon, which is a hamfless carbon particles to i)mge fl'()m the cartridge.

harmless black powder. Turn oft the thucet when the water is clem:

Water hasair bubbles Air in system after installation. "Will go away after water runs for a while.

and is cloudy

Indicator light on the Six months usage has occurred. • Replace both filter cartridges and batteries in the

faucet base is flashing This is the maJdmmn ffe of the batte_ y pack.

(net available en all medels) filter caxtridges.

Indicator light on the The faucet base lead wire • Connect.

faucet base is net working is not commcted to the battery

(notavailable onall models) pack lead wire.

Batteries may need to be • Observe orientation markings on the holder and install

replaced or they may have been correctly. Replace batteries if they are old.

installed incorrectly,

Lead wires damaged. • Inspect and repair as needed.

Chlorine taste and/or The fiher cartridges axe no • Replace both filter cartridges.

odor in the product water longer removhlg chlorine

from the water supply.

Water dispenses Filter may have ma integral "A slower flow (approx. 0.6 g/min.) is nomml with this

veryslowly flow restrictor, style ot filte_: If flow rate is unacceptable, replace the

filte_ with ones that do not have integral flow restricto_

(Filter Numl)er FXUTC).

The filters have been hastalled • A six-month change-out period is recommended.

for too long. Replace both filter cartridges.

The filter cartridges have • High sediment levels can cause premature clogging.

become clogged. Replace both filter cartridges.

Fittingsare leaking Tubing may not be hastalled • Fullx follow the installation instructions (page 9) and

properly, be sure the tubing is installed to the proper depth.

Parts List. www.GEAppliances.com

Electronic

Monitor

Faucet

*NOTE:Codesin thestate ofMassachusetts

requireinstallationbya licensedplumberand

do not permittheuseofthesaddlevalve.

Forinstallation,useplumbingcode248-CMR

of theCommonwealthof Massachusetts.

Toobtainreplacementparts,call toll-free

800.626.2002(U.S.),800.663.6060(Canada-English),

800.361.3869(Canada-French)

GeneralElectricpartscatalog.

REE NO. PART NO,

0001 WS02X 10001

t)t)02 WS28X 10010

0003 WS22X 10008

0004 WS22X 10007

0005 WS02X 10003

0006 WS22X 10(t02

0007 WS 19X 10011

0008 WS03X 10001

0009 WS30X 10002

0010 WS22X 10003

0012 WS07X 10(t08

0015 WS03X 10(t44

0017 WS 15X 10008

0018 WS 15X 10002

WS 10X 10020

WS 10X 10026

0019 WS 10X 10(t08

WS10XI0010

WS 1(IX 10(t22

0020 WS02X 10007

0021 WS 10X 10002

WS 1(IX 10221

WS 10X 10027

0022 WS02X 10008

0023 WS08X 10003

0024 WS06X 10001

0(t25 FXSI.C (rex. 2)

FXSVC (re_; 2)

0200 WX5X140

0999 49-50057

0 G G G

5 N N N

C S S S

B V V V

L 2 3 3

R 5 0 0

E C C C

V B W C

PART DESCRIPTION 2 L W C

S(_REW, #10-14 X 3/4" 8 8 8 8

MOt NTIN(; BRA(_t<ET 1 1 1 l

N[ TI-,3/8" TEBE 2 2 2 2

INSEI/_I. 3/8" TEBE 2 2 2 2

SCREW, #10-14 X 1-1/4" 2 2 2 2

EI.BOW, 3/8" NPT X 3/8" (compression) 2 2 2 2

II EAI) 2 2 2 2

O-RING, 3-3/8" X 3-5/8" 2 2 2 2

SUMP 2 2 2 2

NIPPLE, 3/8" NPT X 1-1/2" 1 1 1 1

TI BING, 3/8" X 20 FT-WII 1 1 1 1

TI BING AI)APTER ASM. 2 2 2 2

SADI)LE 11_IAI< !SUPPIX 1 1 l l

FAI ClqI' ASM. (monitored) (HACK ON CIIROME) 1 1 -

FA[ C1CI' ASM. (monitored) (WttH-E ON WIIH-E) - 1

FA[ ClqI' ASM. (monitored) (I_,ISQ[ E) - - 1

TOP FAI CET BASE (BLACK) l 1 -

TOP FAI 5CET BASE (Wt tH'E) - 1

TOP FAISCET BASE (BISQISE) - - l

S(]REW, #6-32 X 1-3/8" 2 2 2 2

BASE FA[ CET KIT (BLACK) l 1 -

BASE FA[ CET KIT (WI IITE) - 1

BASE FAt C1CF KIT (BIS@SE) - - 1

NET 2 2 2 2

GASKET FAI CET 1 1 1 1

IIOI.DER BAFFH<Y 1 1 1 1

FIIJI'ER S1CF- I.EAI)iCYST 1 -

FIIJI'ER S1CF- V()C - 1 1 1

WRENCtt StMP 1 1 1 1

PM MANI AI [SE & CARI{i

INSTALI.\HON 1 1 1 1

Parts List.

*NOTE:Codesin thestate ofMassachusetts

requireinstallationbya licensedplumber

and donotpermit theuseofthesaddle

valve. Forinstallation,useplumbing code

248-CMRofthe Commonwealthof

Massachusetts.

Toobtainreplacementparts,call toll-free

800.626.2002(U.S.),800.663.6060(Canada-

English),800.361.3869(Canada-French)

GeneralElectricpartscatalog.

I_]E NO. PART NO.

0001 _4S02X10001

0009 _4S98X 10010

0003 WS22X 10008

0004 WS22X 10007

0005 _AS02X 10003

0006 _4S22X 10002

0007 WS19X10011

0008 WS03X10001

0009 _4S30X 10002

0012 _4S07X 10008

0015 WS03X 10044

0017 WS15X10008

0018 _4SI5X10022

0025 _LXUI,C (rev. 2)

0200 WXSX 140

0999 49-50057

PART DESCRIPTION

SCREW, #10-14 X 3/4" 4

MOIJNTING BIL_tCKET 1

NUT, 3/8" TUBE 2

INSERT, 3/8" TUBE 2

SCREW4. #l 0-I 4 X 1-I/4" 2

EI.BO_4. 3/8" NPT X 3/8" (compression) 2

HEAD 1

O-RING, 3-3/8" X 3-5/8" 1

SUMP 1

TUBING, 3/8" X 20 FT - WH 1

TUBING ADAPTER ASM. 2

SADDI,E VALVE/SUPPI,Y 1

FAUCET ASM. (nonmonitored)

(BLACK ON CHROME) 1

F]I FER - I,EAD/(_ST 1

_ARENCH SUMP 1

PM MANUAl, USE & CAP,E/

INSTAI,I ATION 1

GEWater Filtration System Warranty.

_ II warranty service provided by our SmartWateFMAuthorized

Servicer Network. Toschedule service, on-line, 24 hours a day,

vis# us at www.GEAppliances.com, or carl 800.GE.CARES(800.432.2737)

(U.S.),or 866.777.7627(Canada).

Staple your receipt here.

Proof of the original purchase

dateis needed to obtain service

under the warranty.

For The Period Of."

OneYear

Fromthedateof the

originalpurchase

GE Will Replace:

Anypart of the _,_hter Filtration System (excluding tiltei_) which flfils due to a dele(t in materials

or workmanship. During this full one-year warranty,GE will also provide, free ofcharge, all labor

and in-home service to replace the defective part. _MIwarran b' service will be pro\_ded by a (;E

Smart_,_'ater TM Authorized SeIMceI:

What GE Will Not Cover:

• Service trips to your home to teach you how to use

the product.

• Improper hlstallation.

• FaAlure of the product if it is abused, misused, or used

for other than the intended purpose.

• Defects that result from hnproper h_stadlation or damage

not caused by GE.

• Liability on the part of GE under this or may other

warranty for any hadJrect or consequential dmnage.

• Products that are used for commerciaJ or industrial

applicatiol_s.

• Use of this product where water is microbiologicaMy

tmsafe or of m_lown quality, without adequate

disinfection before or after the system. Systems certified

for cyst reduction may be used on dJshffected water that

may contain filterable cysts.

• Filter cartridges.

• Replacement of house fuses or resetting of circuit

breakers.

• Damage to the product caused by accident, fire, floods or

acts of God.

• h_cidentaJ or consequentiaJ damage caused by possible

defects with this applimice.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. In Alaska, the warranty excludes the cost of shipping or service cafls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your

legal rights are, consult your local or state consumer affairs office or your state's Attorney General. THIS

WARRANTY IS INTENDED TO BE IN LIEU OFALL OTHER WARRANTIES, WHETHEREXPRESS ORIMPLIED,

INCLUDING THE WARRANTIES OFMERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE.

Warrantor: General Electric Company.Louisville, KY 40225

ConsumerSupport.

gEAppliancesWebsite www.GEAppliances.com

Have a question or need assistance with your appliance? Try the GE Appliances X_'ebsite 24 hom_ a day,

any day of the year'. For greater convenience and faster service, you can now download Owner's Manuals,

order parts, catalogs, or even schedule service ondine. You C[IXl [llso "Ask O/xY Weanx of EN)erts .....

your questions, and so much more...

ScheduleService

www.GEAppliances.com

Expert (;E repair sexs,ice is only one step away fl'om your doox: Get on-line and schedule your sex'vice

at your, conxenience 24 hom_ am dm (_'fthe _eai ' Or call 800.GE.CARES (800.432.2737) (U.S.) or

866.777.7627 (Canada) (hxxJxlg xloxillal bHsixless hoHxB.

RealLifeDesignStudio www.GEAppliances.com

GE supports the IJni\'ex_al Design concept--products, services and environments that can be used by

people at all ages, sizes and capabilities. We recognize the need to design fin" a wide range of physical and

mental abilities and impaimmnts. For details of GE's lJnivex_al Design applications, including kitchen

design ideas t0r people with disabilities, check out our Website today Fox"the heating impaired, please call

800.TDD.GEAC (800.833.4322).

ExtendedWarranties www.GEAppliances.com

Purchase a GE extended warx'ant_ and learn about special discounts that are a_ailable while your warranla,

is still in effect. You can i)urchase it on-line an) time, or call 800.626.2224 during natural business hom_.

GE (_onsuxner Home Set\ices will still be there after your warrant} expires.

PartsandAccessories www.GEAppliances.com

Individuals qualified to sex_'ice their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line toda> 24 hom_ every day or by phone

at 800.626.2002 (U.S.), 800.663.6060 (Canada-English) or 800.361.3869 (Canada-French) during natural

business hom_.

Instructions contained in this manual cover procedures tobe performed by any user. Other servicing generally should

be referred to qualified service personnel Cautionmust be exercised, since improper servicing may cause unsafe

operation.

ContactUs www.GEAppliances.com

If you are not satisfied with the service you receive ti'om GE, contact us on our _'ebsite with all the details

including your phone numbex; or write to: General Managex; Customer Relations

GE Appliances, Appliance Park

I,ouisville, KY 40225

RegisterYourAppliance www.GEAppliances.com

enhanced communication and prompt service Hxlder the terms of}otxr warx'axltv should the need arise.

You may also mail in the prepfinted registration card included in the I)ackin°_ material.

Printed in flTeUnited States

GE GNSL05CBL Owner's manual

Brand: GE

Model: GNSL05CBL

Type: Owner's manual

This manual is also suitable for

Download PDF

report

GE GNSL05CBL Owner's manual

This manual is also suitable for

GE GNSL05CBL Owner's manual

Related papers

Other documents