Dynex DX-2P2C User manual

USER GUIDE

GUIDE DE L’UTILISATEUR • GUÍA DEL USUARIO

2-Port USB 2.0 PCI card

Carte PCI USB 2.0 à 2 ports

Tarjeta PCI para USB 2.0 de 2 puertos

DX-2P2C

DX-2P2C.fm Page 1 Friday, April 21, 2006 4:48 PM

2

Contents

Dynex DX-2P2C

2-Port USB 2.0 Card

Contents

Introduction .............................................................2

Important safety instructions ...................................2

Setting up the USB card ............................................3

Legal notices .............................................................8

Français........................................ 9

Español .......................................17

Introduction

The DX-2P2C 2-port USB 2.0 PCI card provides two additional USB 2.0

ports for your computer. With these additional ports, you can connect a

USB mouse, keyboard, camera cable, printer, or other high-speed USB

devices.

Important safety instructions

• Always read the safety instructions and User Guide

carefully. Keep the User Guide for future reference.

• When using some operating systems, the driver software

must be installed before operation.

• Do not drop or strike the card, or install it in locations

exposed to heavy vibrations.

• Do not disassemble or modify the card in any way.

Disassembly or modification may not only void the

warranty, but also could cause damage or lead to fires or

electric shock.

DX-2P2C.fm Page 2 Friday, April 21, 2006 4:48 PM

Setting up the USB card

3

• Do not use or store the card in damp locations. Liquid

entering the card may cause damage or lead to fires or

electric shock.

• Before removing the card from its anti-static package,

safely discharge any static electricity buildup which may

damage the computer or the card by touching an

unpainted piece of metal on the computer. Handle the card

by the metal mounting bracket and printed circuit board

edges only. Avoid touching the gold-plated PCI bus

contacts and the on-board electronic components.

• This card is for general computer use. It is not to be used for

equipment requiring exceptional reliability, particularly

when the breakdown or malfunction of this card may

jeopardize life or health.

Setting up the USB card

System requirements

• Computer with one free PCI slot

• Computer with Windows XP SP1 or higher, Windows ME,

Windows 2000, or Windows 98 SE

Installing the USB card

Before installing

• Touch the exposed metal casing on your computer’s power

supply before taking the card from its anti-static package.

This safely discharges any static electricity that may have

built up on your body.

• Handle the card by the edges only. Avoid touching the

gold-plated PCI bus connectors or the electronic

components.

DX-2P2C.fm Page 3 Friday, April 21, 2006 4:48 PM

4

Setting up the USB card

To install the card:

1 Turn off your computer and unplug the power cord and all

cables.

2 Remove your computer’s case cover. See your computer’s

user guide for information about removing the cover.

3 Locate an available PCI slot. PCI slots are usually white.

4 Remove the screw that secures the backplate (the small

piece of metal that covers the opening for the PCI card on

the back panel of your computer), then remove the

backplate. You should store the backplate for future use.

5 Carefully insert the card into the PCI slot, seating it firmly

into the PCI slot. Do not touch the metal connector on the

card.

6 Secure the card to the case using the screw you removed

from the backplate.

7 Reinstall your computer’s case cover.

8 Plug in the power cord and other cables, then turn on your

computer.

DX-2P2C.fm Page 4 Friday, April 21, 2006 4:48 PM

Setting up the USB card

5

Installing the software drivers

To install drivers for Windows XP SP1 (or later) and

Windows 2000:

Note: Driver installation steps may vary from the steps listed

below if you use an upgraded operating system. If the screen

messages differ from the instructions below, follow the

on-screen prompts.

1 Make sure that you have installed the card into your

computer, then turn on your computer.

2 When Windows starts, insert the DX-2P2C CD into your CD

or DVD drive.

3 Run the file setup.exe on the CD. The installation wizard

opens.

4 Click Next.

5 Select Install USB 2.0 Driver, then click Next.

6 Click Yes to continue. Your computer restarts when the

installation is complete.

Note: Microsoft EHCI drivers for Windows XP are not included

in this package. If the following window appears, please

update your system to Windows XP SP1 or SP2, then run the

setup program again.

DX-2P2C.fm Page 5 Friday, April 21, 2006 4:48 PM

6

Setting up the USB card

To verify that your card has been correctly installed:

1 To verify the driver installation, click Start, Control Panel,

then click System. The System Properties dialog box opens.

2 Click the Hardware tab, then click Device Manger. The

Device Manager window opens.

3 Double-click Universal Serial Bus Controllers or click

the plus (+) sign next to it. The following entries should be

visible:

• VIA Rev 5 or later USB Universal Host Companion

Controller

• VIA Rev 5 or later USB Universal Host Companion

Controller

• VIA PCI to USB Enhanced Host Controller

• USB Root Hub

To install drivers for Windows Me and Windows 98:

1 Make sure that you have installed the card into your

computer, then turn on your computer.

2 When Windows starts, insert the DX-2P2C CD into your CD

or DVD drive.

DX-2P2C.fm Page 6 Friday, April 21, 2006 4:48 PM

Setting up the USB card

7

3 Run the file setup.exe on the CD. The installation wizard

opens.

4 Click Next.

5 Select Install USB 2.0 Driver, then click Next.

6 Click Finish to complete the installation. Your computer

restarts.

To verify that your card has been correctly installed:

1 To verify the driver installation, click Start, Control Panel,

then click System. The System Properties dialog box opens.

2 Click the Hardware tab, then click Device Manger. The

Device Manager window opens.

DX-2P2C.fm Page 7 Friday, April 21, 2006 4:48 PM

8

Legal notices

3 Double-click Universal Serial Bus Controllers or click

the plus (+) sign next to it. The following entries should be

visible:

• VIA Tech 3038 PCI to USB Universal Host Controller

• VIA PCI to USB Enhanced Host Controller

• USB2.0 Root Hub Device

• USB Root Hub

Uninstalling the drivers

To uninstall the drivers:

1 Insert the DX-2P2C CD into your CD or DVD drive.

2 Run the file setup.exe on the CD. The installation wizard

opens.

3 Click Next.

4 Select Install USB 2.0 Driver, then click Next.

5 Click Yes to uninstall the drivers. Your computer restarts

when the driver has been completely uninstalled.

Legal notices

Enterprise Services, Inc. Other brands and product names are trademarks

or registered trademarks of their respective holders. Specifications and

features are subject to change without notice or obligation.

For service and support call (800) 305-2204.

DX-2P2C.fm Page 8 Friday, April 21, 2006 4:48 PM

Page is loading ...

Avisos legales

25

DX-2P2C.fm Page 25 Friday, April 21, 2006 4:48 PM

www.dynexproducts.com (800) 305-2204

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave. South, Richfield, MN 55423 U.S.A.

Distribué par Best Buy Purchasing, LLC

7601 Penn Ave. South, Richfield, MN 55423 É.-U.

Distribuido por Best Buy Purchasing, LLC

7601 Penn Ave. South, Richfield, MN 55423 U.S.A.

R1

DX-2P2C.fm Page 26 Friday, April 21, 2006 4:48 PM

Dynex DX-2P2C User manual

Dynex DX-2P2C User manual

in other languages

Related papers

Other documents