Fiberon POST SLV KIT 45 S BL User manual

Brand: Fiberon

Model: POST SLV KIT 45 S BL

Type: User manual

FOR FIBERON DECKING AND RAILING

CARE AND

MAINTENANCE

TABLE OF CONTENTS

GENERAL CARE AND MAINTENANCE

SPECIAL CONSIDERATIONS

Dirt and grime 1

Oil and grease 4

Mold and mildew 4

Salt and calcium chloride 5

Construction materials 6

Railing 7

Low-E glass and reflected heat 8

Fire features/fire pits 8

Rubber mats and flower pots 9

Static electricity 9

Under-deck waterproofing systems 9

Ladder usage tips 9

Paramount PVC Decking 10

GET READY TO ENJOY YEARS OF

EASY OUTDOOR LIVING

Fiberon

composite decking and railing is designed to be long lasting and low maintenance. Of course, life happens.

Use this guide to help you manage the occasional mess or mishap. And thanks for choosing Fiberon!

GENERAL CARE AND MAINTENANCE

DIRT AND GRIME

In most cases, an occasional soap and water cleaning is all that is needed to keep your Fiberon decking looking like new.

For best results, use the following:

A pump sprayer

Mild household cleaner or composite decking cleaner

Non-metal scrub brush (with extension handle, if possible).

A NOTE ABOUT

PRESSURE WASHERS:

Used incorrectly, pressure washers can damage

your decking. Exercise extreme caution with

pressure washers. Pressure should be less

than 2500 psi at 12 inches above deck surface.

ALWAYS use a wide fan-tip nozzle or oscillating

nozzle and test in an inconspicuous area first.

Wash in direction of grain pattern to avoid

possible damage to the boards.

CARE AND MAINTENANCE — 1 — CLEANING YOUR DECK

Clean debris from the spaces between boards to ensure proper drainage. If the

gap between decking boards is less than 3/16 inch (4.8 mm), organic debris such

as leaves, seeds, or pollen can settle on the deck and clog gaps. Water can pool,

steeping organic debris. This will result in a “tea” or tannin which could stain your

decking. Standing water could also cause the boards to swell, resulting in cracking,

warping, and cupping of the material.

Remove the grill, furniture, and other items from the deck.

Sweep the surface or use a blower to

remove loose debris such as leaves.

CARE AND MAINTENANCE — 2 — CLEANING YOUR DECK

If you are cleaning your deck in direct sunlight, work in very small

sections. The decking needs to stay wet during the entire process

to allow for all dirt and soap residue to be rinsed off completely.

Before applying the cleaner, review instructions

for the particular product you are using.

Using a sprayer, apply the cleaner onto the dry deck. Do not

let the product dry on the boards. Work in small sections and

always keep the decking wet during the cleaning process.

Rinse the section of the deck completely with regular water.

Repeat these steps until the entire surface has been cleaned.

CARE AND MAINTENANCE — 3 — CLEANING YOUR DECK

Gently scrub the surface of the deck with an appropriate non-

metal brush. For tougher stains, allow cleaner to sit for 10-15

minutes, but continue to wet down the decking while you wait.

Let the deck dry completely before putting

any furniture or other accessories back.

OIL AND GREASE

Speedy clean-up is best. For grease and

oil stains that soap and water cannot

remove, an all-purpose cleaner such as

Fantastik should do the trick. Or, use

a commercial deck cleaner designed

specifically for your type of decking.

De-Solv-It

Citrus Solution is effective

in removing tar, asphalt, oil, grease,

and chewing gum. Be sure to follow the

manufacturer’s recommendations and

test in an inconspicuous area prior to

cleaning the entire deck.

MOLD AND MILDEW

Tiny and lightweight, mold spores travel easily through the air. To thrive, mold and mildew need

air, water, elevated temperatures, and a food source such as decaying wood, leaves, or pollen.

Mold can grow almost anywhere. To minimize mold on your deck, clean it as often as needed,

at least once per year. Climate conditions vary in different regions of the country and may

necessitate more frequent cleaning.

If mold is present on your deck, there are many commercial products available for removing it.

Collier Manufacturing 30-Seconds

Outdoor Cleaner is a heavy duty, mildly alkaline, chlorinated

mold and mildew cleaner that is biodegradable once rinsed into the soil. During testing, it

performed well in removing mold and mildew.

For best results, be sure to follow the manufacturer’s instructions and use cleaners within their

stated shelf life. Do not mix recommended cleaning products together as harmful chemical

reactions could occur.

To learn more, read Fiberon

Technical Bulletin: Cleaning Mold on

Capped and Uncapped Decking.

CARE AND MAINTENANCE — 4 — CLEANING YOUR DECK

CARE AND MAINTENANCE — 5 — CLEANING YOUR DECK

SALT AND CALCIUM CHLORIDE

Choosing the best ice melt product

Cleaning up ice melt debris quickly and easily

If the winter weather has left your deck slippery or ice-covered, choose calcium chloride-based "ice melt"

or rock salt to remove the snow and ice.

Don’t use sand as it is naturally abrasive and could easily damage the surface of the deck boards.

Look for the phrases "safe for concrete,” "safe for flagstone," and "will not kill grass" in the ice melt

product description.

Avoid ice melt with added colorant. These dyes can stain composite or PVC decking.

If you have children or pets that frequent your deck in the winter, ensure your chosen product will be safe

for them as well.

When the threat of inclement weather has passed, use a broom to sweep up any existing granular pieces and

discard the ice melt. This will prevent people and pets from tracking in ice melt that could damage indoor flooring.

Remove any remaining buildup of ice melt with water and a light scrubbing. Use a non-metal deck brush.

When warmer temperatures return, it’s best to rinse your deck with a garden hose to remove any stubborn

leftover debris.

TIPS FOR SNOW REMOVAL:

A leaf blower or broom should easily clear a light

dusting of snow.

Never use metal shovels or sharp-edge tools

when removing snow or ice from your composite

or PVC deck. Even the most resilient boards

could be scratched or gouged.

Plastic shovels or plastic/nylon bristled deck

brooms will remove snow from the deck as well

as limit the risk of scratches to the deck surface.

When clearing snow, always shovel in a path

parallel to the deck boards, not perpendicular.

Never use an ice chipper — even a plastic one —

on your deck, at the risk of permanent damage.

CARE AND MAINTENANCE — 6 — CLEANING YOUR DECK

CONSTRUCTION MATERIALS

Construction Chalk

Masonry Construction

Colored chalk used in construction for marking straight lines prior to cutting is permanent on most surfaces. Contact the

specific chalk manufacturer for a cleaning solution that may prove effective. The best advice is to avoid colored chalk.

Instead, use a workable alternative such as white chalk or baby powder.

Always protect decking during masonry construction. White or hazy residue from mineral deposits (efflorescence) can

leach out of stone and masonry material after water evaporates, leaving the deposits behind. Minerals from soils in

certain arid and mountainous environments can also cause a hazing affect when deposited on the deck surface.

To prevent this, either cover the decking surface completely and securely during the construction phase or wait to

install the decking until after masonry construction has been completed. To minimize this effect during masonry

construction, keep materials dry and allow masonry and cement to cure properly.

For mineral deposits left on the decking surface, periodic cleaning is required. Use mild soap or a composite decking

cleaner, and be sure to follow the label instructions carefully. Do not mix recommended cleaning products together

as harmful chemical reactions could occur. NOTE: For Symmetry

Decking, use a soft nylon deck brush, not a brass

bristle brush.

CHOOSE YOUR BRUSH CAREFULLY:

For stubborn or hard-to-remove stains, we recommend a soft, brass bristle brush

for all Fiberon Decking EXCEPT Symmetry Decking. Use a soft nylon deck brush

for Symmetry Decking to avoid potential scratching.

RAILING

For general cleaning, use mild soap and water or Fantastik

spray cleaner. For white railing only, you may also use Mr. Clean

Magic Erasers. For deeper cleaning, or to remove any oxidation, we recommend DeckMAX

PVC Revitalizing Wipes.

CARE AND MAINTENANCE — 7 — CLEANING YOUR DECK

CARE AND MAINTENANCE — 8 — CLEANING YOUR DECK

FIRE AND POTENTIAL HEAT SOURCES

Composite decking will retain heat when exposed to direct or reflective sunlight. Exercise caution if walking barefoot.

Footwear may be required. Heat build-up from external sources could possibly damage Fiberon decking surfaces.

Examples would include reflected light from different types of glass (ex. low-e glass), fire features, and under-deck

waterproofing installations that do not provide the 1.5 inches (4 cm) of unobstructed ventilation.

LOW-E GLASS/REFLECTED HEAT

Low-emissivity (Low-E) glass is designed to prevent heat gain inside the house by reflecting sunlight outward. This reflective

property can result in excessive heat build-up on the surface of Fiberon decking. Damage caused could include melting,

sagging, warping, discoloration, increased expansion and contraction, and accelerated weathering.

If you have questions on how to reduce this risk, contact the manufacturer of the product containing the Low-E glass for

suggestions on how to reduce or eliminate the reflected heat.

FIRE FEATURES/FIRE PITS AND GRILLS

Fire features and fire pits are increasingly popular in outdoor living environments. Improperly installed fire features or fire

pits can damage the surface of Fiberon decking via direct exposure to the flame or excessive radiated heat. Proper caution

should be taken when designing, installing, and using these features to ensure damage does not result. Fire features and

grills should be kept at least 12 inches from the deck and rail surfaces.

SPECIAL CONSIDERATIONS

CARE AND MAINTENANCE — 9 — CLEANING YOUR DECK

RUBBER MATS

STATIC

Dry or windy environments may create a temporary condition of static electricity. Climate and site conditions may also

influence the occurrence of static electricity. Heat pumps and dryer vents that are close to, or pointed toward the decking

material, can also generate static electricity on the deck. Always position the dryer vents away from the deck. In the case of

excessive static buildup on an installed PVC or capped composite deck, we recommend the following:

1. Remove loose debris from the deck surface.

2. Dilute ACL Staticide

Concentrate 1 part to 39 parts water (1:39).

3. Spray or mop entire surface of the deck. Allow to air dry. Do not attempt to wipe the surface dry as wiping will reduce the

effectiveness of the anti-static coating.

(*Although very safe in diluted form, ACL Staticide Concentrate is considered a hazardous chemical if left undiluted. DO NOT

use ACL Staticide Concentrate undiluted.)

Welcome mats or grill mats with a rubber, vinyl or latex backing can mark your deck. The marks can be removed; however,

we recommend using high-quality polypropylene or colorfast woven rugs to avoid the problem. Flower pots can also create

potential problems. When pots, trays, etc., sit directly on the deck surface, moisture can get trapped. Over time, minerals

and fertilizer/plant food can build up and result in a white discoloration on the boards. We recommend using a plant stand or

other structure to elevate the pot and enable air flow underneath.

UNDER-DECK WATERPROOFING SYSTEMS

Properly installed, under-deck waterproofing systems can provide additional living or storage space. Improper installations

are those that restrict air flow and result in buildup of heat and/or humidity, which can result in unwanted consequences.

Contact the manufacturer of the specific under-deck waterproofing system for installation instructions to ensure the

required 1.5 inches (4 cm) of unobstructed cross-ventilation and air flow is achieved. If already installed, seek methods to

achieve the cross-ventilation requirement.

LADDER USAGE TIPS

When using a ladder, place it on a piece of 3/4-inch plywood firmly secured to the deck surface. This will

disperse the load of the ladder’s feet to nearby underlying joists.

Drill fasteners downward through the top of the plywood sheet into the deck board gaps. Ensure fasteners

reach into the joists to keep the plywood from slipping. This will avoid holes left in your decking once the

plywood sheet is removed.

Always follow the ladder manufacturer’s instructions and safety tips as well.

Fiberon, Symmetry, and Paramount trademarks of Fiber Composites, LLC, registered in the U.S.

and other countries. All other register marks are the properties of their respective companies.

FIBERON PARAMOUNT PVC DECKING

Recommended cleaners for Paramount

PVC Decking include Simple Green, Krud Kutter

Cleaner Degreaser

and DeckMAX

PVC Revitalizing Wipes. Follow the manufacturer’s instructions and test in an inconspicuous

area prior to using on the deck surface.

Certain chemical ingredients in insect repellents and sunblock could cause a reaction and leave a stain on

the decking surface. Do not apply these products while standing on the deck. Similarly, if you have sunblock,

suntan lotion, or insect repellant on your feet, do not walk on the decking barefoot. The product could rub off

onto the boards.

Get to know us even better.

Made in the USA

berondecking.com | 1.800.573.8841

MKT LIT CARE-MAINTENANCE 5/18

Fiberon POST SLV KIT 45 S BL User manual

Fiberon POST SLV KIT 45 S BL User manual

Fiberon POST SLV KIT 45 S BL User manual

Related papers

Other documents