Hanover ORL5PCTFPSW4-NVY Installation guide

Brand: Hanover

Model: ORL5PCTFPSW4-NVY

Category: Fireplaces

Type: Installation guide

This manual is also suitable for



HanoverOutdoorFurniture



IMPORTANT

Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),

PLEASEDONOTRETURNTOTHERETAILER/STORE

fromwhereyoupurchasedtheproduct.

PleasecallourToll‐FreeCustomerServiceHotlineat:

1‐800‐416‐3511

Between9:00AMand5:00PMEasternTime,MondaythroughFriday

Orvisitourwebsiteat:

www.hanover‐products.com



Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty

Cardandreceiptforfutureuse.

For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor

furniture,pleasevisitourwebsiteat:www.hanover‐products.com. 

6/1/2015(a)

Page 2

Outdoor Furniture

1-Year Limited Warranty Program

Contact Warranty Services at

1-800-416-3511

For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this

Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the

original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty

revert back to the date of original purchase for future warranty.

Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies in normal

residential use only and is not intended for commercial use. Manufacturer can make substitutions as required of materials,

components, and sub-components of comparable value and utility. This warranty is limited to product repair or replacement (to be

determined solely by Manufacturer). Warranty return is limited to only the single affected component.

This warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but

not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to

extreme heat or cold, abrasion or excessive weight. This product is intended to be used in standard installations only. This warranty

is invalid if the product is not used for intended purpose. Manufacturer disclaims liability for any aspect of installation and any

inconvenience caused by a defective part of a component.

Certain items are not covered by this warranty. These include, but are not limited to the following:

1. Components subjected to abuse, including abuse intended to simulate failure.

2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).

3. Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches or stretching of

materials and stitching.

4. Tears, punctures, scratches or any damage caused by improper installation or use.

5. Damage to frames/welds resulting from improper assembly or exposure to water and/or sub-freezing temperatures is not

covered. General frame rusting is not covered.

6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids

or any other cause are not covered.

7. Umbrella bases are not covered under any circumstances.

8. Items sold “as is” or floor models.

To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt along with a brief

description of the problem. Please also provide your email address and daytime telephone or cell phone #. Repairs or replacement will

be made at the Manufacturer’s option.

THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE

FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS

EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY

PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS

WARRANTY. NEITHER THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL,

INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER

THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

Sales and use taxes, plus shipping and handling charges are the responsibility of the consumer.

Page 3

Care & Maintenance

Outdoor furniture can be enjoyed for many years when well maintained.

Regular Maintenance

How to Clean & Care for Teak Furnishings

How to Clean Woven Furnishings

How to Clean Fabric

How to Clean Mesh

How to Clean Strap

How to Clean Vinyl Strap

How to Clean & Care for Stone and Marble Tops

Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a

fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air.

For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution

areas. Please note that these durable materials can be safely cleaned as often as desired. Note: Some suntan and sun block products

may be harmful to resin, cushions and strap, mesh and vinyl lace and strap. Do not allow such products to come in contact with any

seating surfaces to avoid deep penetrating stains, which are not covered under warranty.

Left alone to age, the natural color of teak furnishings will weather to a soft, silver grey. This process will take approximately nine

months, depending on the degree of sunlight and rain exposure. Imperfections, which are inherent properties of the wood, will show

over time, enhancing the beauty of the furniture. In humid or wet climates, or after rains, the wood may naturally expand and contract,

causing the grain to rise. This is to be expected with exposure to the elements and will stabilize after the initial weathering occurs.

To maintain teak furnishings, use a soft bristled utility brush and stroke lightly in the direction of the grain to remove surface dust. For

more stubborn dirt, the wood may be washed with a mild solution of four parts laundry detergent or dish washing soap to one part

bleach in water, then rinsed thoroughly and allowed to dry completely. Oiling the wood may cause mildew or irregular coloring.

Woven furnishings are made of durable and weatherproof extruded polyethylene resin weave. Light stains and soils may be removed

with a solution of mild detergent and water, rinsed with clear water and dried thoroughly. Mildew and heavy stains can be removed with

a quality commercial outdoor furniture cleaner and protectant. Woven furnishings may not be suitable for intensely hot climates.

Fine outdoor fabrics are designed to endure years of sun, soil and moisture. Wash outdoor cushions with a solution of mild detergent

and water and thoroughly rinse with clear water. Stand cushions on end and allow to air dry completely. Light stains can be removed as

above. Mildew and heavy stains can be removed with a quality commercial outdoor furniture cleaner and protectant. Note: Do not dry

clean or use a washing machine or dryer. Do not steam or use water at temperatures above 100º F when washing. Note: Be careful to

keep the outdoor furniture cleaner from contact with the cushions of your outdoor furniture, as it will cause discoloration. Do not use

bleach on printed acrylic fabrics. Do not use solvent-type materials on woven vinyl, woven blend or ultra woven blend fabrics as they

will damage the yarns. Do not use chlorine based cleaners.

Remove light stains with a solution of mild detergent and water, then rinse with clear water and dry thoroughly. Mildew and heavy

stains can be removed with a quality commercial outdoor furniture cleaner and protectant.

For general or light cleaning, begin by brushing dirt off the strap. Apply a solution of mild detergent and warm water and allow it to soak

into the strap. Gently clean with a sponge or soft bristle brush, then rinse thoroughly with clear water and allow the strap to air dry.

Apply a quality vinyl protectant to guard against the effects of air pollution, salt air build-up, and mildew. To remove difficult stains use

rubbing alcohol applied with a soft cloth.

Tabletops are designed for normal outdoor use in residential settings. To maintain the natural beauty we recommend resealing your

table top when necessary, with the same sealer product applied during the manufacturing process. The sealer penetrates the stone

and acts as a repellent, preventing absorption of moisture and stainable materials.

If tabletop is stained with products such as wine, soda, coffee, or other colorants of organic origin, clean these spills immediately with a

mild detergent then rinse with water. In extreme cold climates, it is recommended that tabletops be stored in a dry indoor area or be

covered with suitable outdoor furniture cover. Be sure to allow space between the tabletop and the cover so that moisture does not

collect on the table; this will promote airflow and allow moisture to escape.

Page 4

ASSEMBLY INSTRUCTIONS

Assemble furniture on a smooth, non-abrasive surface. by using two

5/16"x40 mm bolts and washers as shown in . Guide the bolts through holes in back frame, into

pre-drilled holes in the . and back frame

by using four 5/16"x25 mm bolts and washers as shown in . A

and seat frame by using two 5/16"x25 mm bolts and two 5/16"x40 mm bolts and four washers as

shown in .

Fig.1

Hand tighten only.

Fig.2 Hand tighten only.

Fig.3 Hand tighten only.

Attach the back frame to right arm

right arm Attach the seat frame to right arm

ttach the left arm

to back

Fig.1

Fig.2

Fig.3

Attach the complete base to the complete seat by using four 5/16"x40 mm bolts and washers as shown

in . Guide the bolts through holes in base, into the pre-drilled holes in the seat.Fig.4 Hand tighten only.

Using the hex bolt driver provided, tighten all bolts.

Test the operation of glider. Gliding

motion should be smooth. Adjust tension on the glider brackets, nuts and bolts as needed. Cover nuts

and bolts with covers provided.

Do not over tighten bolts. If nuts and bolts are

too tight or too loose, the glider will not function properly.

Fig.4

Page 5

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE

PARTS IDENTIFICATION LIST

G0080

PARTS LIST

HW0695

HEX BOLT DRIVER

HW0006

SEAT FRAME

DESCRIPTION ORDER PART #

QTY

GLIDER BRACKET

FACTORY ASSEMBLY

ST4 8 X 25 BOLT.

FACTORY ASSEMBLY

FOOT CAP

FACTORY ASSEMBLY

FC0013

5/16" X 25 MM BOLT

HW0186

5/16" X 40 MM BOLT

HW0275

HW0005Ø8.5 X 1.5 MM WASHER

BOLT COVER

HW0105

BACK FRAME

LEFT ARM

RIGHT ARM

GLIDER BASE W/

GLIDER BRACKET

SG0154

SG0155

SG0156

SG0157

SG0158

SG0159

BGS12023

ASSEMBLY INSTRUCTIONS

WARNING

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

An LP-cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, keep away from

the appliance and immediately call

your gas supplier or fire department.

WARNING:

USE FACTORY APPROVED

REPLACEMENT PARTS AND

ACCESSORIES ONLY. USE

OF UNAPPROVED PART OR

ACCESSORIES CAN VOID

THE WARRANTY ON THIS

PRODUCT AND RESULT IN

AHAZARDOUS CONDITION.

PLEASE CONTACT US FOR

INFORMATION REGARDING

REPLACEMNT

HOSES,THERMOCOUPLES,

ELECTRODES,IGNITION

MODULES,LAVAROCKS,LO

GS, FIRE ICE, ETC.

WARNING:

Improper installation, adjustment alteration,

service or maintenance can cause injury or

property damage. Read the installation,

operating and maintenance instructions

thoroughly before installing or servicing this

equipment.

FOR USE WITH 20LB (9KG) PROPANE

CYLINDER WITH TYPE 1 CONNECTION OR FOR

USE WITH NATURAL GAS AFTER CONVERSION

KIT IS INSTALLED (MUST BE PROFESSIONALLY

INSTALLED) ALSO THE LP REGULATOR MUST

BE SUPPLIED BY THE MANUFACTURER.

Dec 2014

Installer: Leave these instructions with consumer.

Consumer: Keep these instructions for future reference.

WARNING: For Outdoor Use Only

Questions, Problems, Missing Parts? Before returning to

your retailer, call our customer service department in the

US and Canada at 1-800-416-3511, Monday-Friday, 9 a.m.–

5 p.m. Eastern Time.

This appliance can produce carbon

monoxide which has no odor.

Using it in an enclosed space can kill

you.

Never use this appliance in an enclosed

space such as a camper, tent, car or

home.

DANGER CARBON MONOXIDE HAZARD

CSA Model 99000

ARL00100

IMPORTANT SAFETY INFORMATION

The installation must conform with local codes or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural

Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code,

B149.2, as applicable.

The appliance must be isolated from the gas supply piping system by closing its

equipment shutoff valve during any pressure testing of the gas supply system at test

pressure equal to or less than 1/2 psi (3.5kPa).

The appliance area must be kept clear and free from combustible materials, gasoline and

other flammable vapors and liquids.

Do not use this appliance if any part has been under water. Immediately call a qualified

service technician to inspect the appliance and to replace any part of the control system

and any gas control which has been under water.

Children and adults should be alerted to the hazards of high surface temperatures

and kept at a safe distance to avoid burns or clothing ignition.

Young children should be carefully supervised when they are anywhere near the

appliance.

Clothing or other flammable material should not be hung from the appliance, or

placed on or near the appliance.

Any screen or guard removed for servicing an appliance must be replaced prior to

operating the appliance.

Installation and repair should be done by a qualified service person. The appliance

should be inspected before use and at least annually by a professional service

person. More frequent cleaning may be required as necessary. It is imperative that

the control compartments, burners and circulating air passageways of the

appliance be kept clean.

Do NOT burn solid fuels in this gas fireplace.

CAUTION: The propane gas pressure regulator provided with this appliance must be

used. This regulator is set for an outlet pressure of 11 inches water column.

This outdoor gas appliance is not intended to be installed in or on recreational vehicles

and/or boats.

Before each use of this gas appliance, open the LP (Liquid Propane) Tank Drawer and

inspect the LP Hose. If there is evidence of excessive abrasion or wear, or the hose is cut,

it must be replaced prior to the gas appliance being put into operation. Use only the

replacement hose assembly specified in this manual. Inspect the burner before each use

of the appliance. The burner must be replaced prior to the appliance being put into

operation if it is evident that the burner is damaged. Use only the burner listed in these

instructions.

Keep the fuel supply hose away from any heated surfaces.

IMPORTANT SAFETY INFORMATION ABOUT

PROPANE (LP) GAS

A self contained LP-gas cylinder for use with this appliance must have a

capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD

(overfill protection device). See Figure 1.

The LP-gas supply cylinder to be used must be constructed and marked in

accordance with the specification for LP-gas cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339,

Cylinder, Sphere and Tubes for the Transportation of Dangerous Goods.

 The cylinder supply system must be arranged for vapor withdrawal.

 The cylinder used must include a collar to protect the cylinder valve.

 This appliance shall be used only outdoors in a well-ventilated space and

shall not be used in a building, garage or any other enclosed space.

 When this appliance is not is use, the gas must be turned off at the supply

cylinder.

 Storage of this appliance indoors is permissible only if the cylinder is

disconnected and removed from the appliance.

 Cylinders must be stored outdoors in a well-ventilated area out of the

reach of children .Disconnected cylinders must have threaded valve plugs

tightly installed and must not be stored in a building, garage or any other

enclosed areas.

CSA (Canadian Standards Association) certified to ANSI Z21.97•CSA

2.41-2012 “ Outdoor Decorative Gas Appliances”

Figure 1

SPECIFICATIONS

INPUT 40,000 Btu/hr 30,000 Btu/hr Low fire

Propane Regulator Pressure 11 inches water column

Clearances to combustible

surfaces

Sides 24in./61cm Top: 72 in. / 183 cm

PARTS IDENTIFICATION LIST

PART DESCRIPTION PART# QTY

CONTROL KNOB FP1245 1

GAS VALVE FP0307 1

THERMOCOUPLE FP0004 1

LP REGULATOR

HOSE

65-FP-0181 1

ELECTRODE 65-FP-0128 1

ORIFICE ELBOW FP0310 1

IGNITION MODULE FP0006 1

PROPANE

ORIFICE

ZCF0021 1

“AAA”

BATTERY(1.5V)

HW0705 1

LAVA ROCK SET FP0002 1

FOOTCAP FC0559 4

1/4" X 15 MM BOLT HW0034 8

1/4" X 20 MM BOLT HW0036 4

1/4" X 40 MM BOLT HW0086 4

BOLT COVER HW0105 18

Ø6.5 X 1.0 MM

WASHER

HW0004 14

Ø18XØ6.5 X1.5MM

WASHER

HW0103 4

NUTS HW0717 2

HEX BOLT DRIVER HW0006 1

HEX WRENCH HW0008 1

FIREPIT TABLE

TOP

BACK PANEL 1

LEFT SIDE

PANEL

RIGHT SIDE

PANEL

DOOR PANEL 1

MIDDLE SUPPORT 1

LP SUPPORT 1

BOTTOM/ TOP

CONNECTOR

INSTALLATION

1.Identify parts packed in carton against the parts list. Remove all protective materials and

set parts on a flat, non-abrasive surface.

2. Attach the back panel to the side panels by using four 1/4"x40 mm bolts and washers

as shown in Figure 2.Guide the bolts through the holes in back panel, into the pre-drilled

holes in the side panels. Hand tighten only.

Figure 2

3. Attach the middle support to the side panels by using four 1/4"x15 mm bolts and

washers as shown in Figure 3.Guide the bolts through the holes in the middle support, into

the pre-drilled holes in the side panels. Hand tighten only.

Figure 3

4. Attach the "L" connector to right side panel by using a 1/4"x15 mm bolt and washer as

shown in Figure 4.Guide the bolt through the hole in the "L" connector, into the pre-drilled

hole in the right side panel. Do not over tighten.

Figure 4

5. Put the door onto the bottom connector, guide the pin in the bottom connector into the

hole on the underside of the door. Then guide the pin on the top connector into the hole in

the topside of the door, use a 1/4"x15 mm bolt and washer to attach this top connector to

the right side panel as shown in

Figure 5. Do not over tighten.

Figure 5

6. With the help of another person, carefully place the table top onto the table base. After

making any necessary adjustments to the alignment of the table top and the assembled

base, use four 1/4"x20 mm bolts and washers as shown in Figure 6.Guide the bolts

through the holes in the base, into the pre drilled holes in the table top. Do not tighten

completely.

Figure 6

7. Attach the LP support the to door panel by using four 1/4"x15 mm bolts and washers as

shown in Figure 7. Do not over tighten.

Figure 7

8. Place gas tank onto the LP support as shown in Figure 8.

9. Attach the metal ring ( as shown in Figure 9) pre-fitted with gas hose which is

connected to the table top , into the hole of the door panel, then use hex bolt driver to

screw 1/4"x5mm nut , the gas tank has fixed as shown in Figure 9a. Connect the regulator

as shown in Figure.10 Screw the black handle clock-wise to tighten. Turn the handle

counter clock-wise to remove. The hose must point down. Check that the valve is turned

all the way clockwise to the "OFF" position.

Figure 8

Figure 9

Figure 10

10. After making any necessary adjustments to the parts, use the hex bolt driver to tighten

all bolts.

Note: each bolt must be tightened a few revolutions at a time.

Repeat until all bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover

all bolts with covers.

12. Pour the lava rocks into the burner pan completely covering the burner. See Figure 11.

Ignition Well

Figure 11

Figure 9a

13. Remove the cardboard cover from the ignition well as shown in Figure 12. Remove

any lava rock or fire ice on top of ignition well.

Cardboard Cover

14. Open the tank valve. Apply a solution of soapy water to the tank-regulator connection

and to the valve-hose connection to check for leaks as shown in Figure 13. If soap

bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve

and tighten all connections.

NOTE: NEVER USE A FLAME TO CHECK FOR LEAKS.

BATTERIES

Make sure the control knob is in the "OFF" position.

Unscrew the push button cap on the ignition module located

on the control panel to access the battery compartment. The

ignition module requires one Alkaline AAA size battery

(1.5V). The negative (-) end goes in first. See Figure 14.

Dispose of battery safely. May explode or leak if charged or

disposed of in fire. Make sure of the polarity. Mercury and

cadmium free.

Figure 14

Figure 12

Checking the tank-regulator for leaks

Figure 13

LIGHTING INSTRUCTIONS

Warning: If these instructions are not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

1. Make sure the control knob is in the "OFF" position. See Figure 15 Open the tank

valve all the way.

2. Push in the igniter button. You will hear a slight clicking sound. With the igniter button

pushed in, push and turn the control knob to the “ON” position. the fire should light within a

few seconds. Once the flame is lit, release the igniter button and continue to hold the

control knob in for 10 to 15 seconds. Release the control knob. The control knob should

pop back out and then remain lit.

Note: If the fire does not light, turn the knob to the “OFF” position and wait five (5) minutes

before trying again.

3. To turn down the flame, push the control knob in slightly and turn to Medium (medium

or Low (small flame).

4. To shut down the fire pit, turn the control knob to the “OFF” position and turn off the tank

valve.

MAINTENANCE

The flames should look like those in Figure 16. To clean the

burner, use a soft brush after the burner has cooled

completely. Never use a vacuum cleaner on the burner. It is

recommended that the fire pit be stored indoors during the

winter if it will be subjected to freezing temperatures. The LP

cylinder must be disconnected and removed from the

appliance before the appliance can be stored indoors.

Figure 16

IGNITER BUTTON CONTROL KNOB

Figure 15

TROUBLESHOOTING GUIDE

PROBLEM CAUSE REMEDY

No Propane Gas at Burner

Check that gas tank valve is

open. Turn control knob to

“ON” and push control knob

in. Make sure tank has

propane gas.

No Spark at Electrode

Check that AAA battery is

installed with negative (-) end

first and has a charge. Check

that the wire is connected to

the ignition module. Check

that the electrode is not

cracked or broken.

Burner won’t light

Lack of oxygen

Remove excess lava rocks or

fire ices from around the

ignition well.

Thermocouple not in flame

Check that the tip of the

thermocouple is

even with the top of the

ignition well.

Remove any lava rocks from

the igntion well.

Thermocouple connection

at the main control valve is

loose

Tighten the thermocouple nut

at the back of

the valve.

Burner won’t stay

lit after lighting

No Lava Rocks on Burner

Cover the burner with lava

rocks per the instructions

Hanover ORL5PCTFPSW4-NVY Installation guide

Brand: Hanover

Model: ORL5PCTFPSW4-NVY

Category: Fireplaces

Type: Installation guide

This manual is also suitable for

Download PDF

report

Hanover ORL5PCTFPSW4-NVY Installation guide

This manual is also suitable for

Hanover ORL5PCTFPSW4-NVY Installation guide

Related papers

Other documents