BG-N18
BAT TERY GRIP
Designed for the
Nikon D7500 DSLR Camera
USER’S MANUAL
Introduction
Thank you for choosing Vello and congratulations on your
new BG-N18 battery grip purchase. Enjoy the benefits
that a battery grip offers, such as comfort and control
when shooting in a vertical (portrait) orientation. The
Vello BG-N18 is compatible with the Nikon D7500 DSLR
camera. It accepts an EN-EL15a rechargeable battery and
offers an alternate shutter-release button.
Please read through this entire manual
before using the BG-N18 battery grip.
2
Precautions
1.
The BG-N18 should be used with only compatible
devices specified in this manual.
2. Use only with batteries recommended in this manual.
3.
If you notice smoke, an unusual smell, or noise from
the battery pack, discontinue use immediately. Remove
the batteries and take the device to a Vello authorized
reseller.
4.
The battery level may not display properly if batteries
are installed before mounting the grip.
5. Remove batteries from the grip when not in use.
6. Do not attempt to disassemble.
7.
Do not expose this product to water or extreme
humidity, and keep in a dry cool place.
8. Keep out of reach of children.
9. All images are for illustrative purposes only.
3
OVERVIEW INTRODUCTION
ASSEMBLY
Overview
1
2
7
12
10
6
3
4
5
9
11
8
4
1
Shutter Release Button
Use as an alternate shutter release
button for shooting in vertical
(portrait) mode.
2
Nonslip Rubber Grip
Provides a secure and comfortable
grip when shooting vertically.
3
1/4"-20 Tripod Socket
Allows for mounting to a tripod when
the grip is attached to your camera.
4
Locking Wheel
Secures the grip to the camera’s
tripod socket.
5
Camera Battery Door Holder
Stores the camera’s battery chamber
door when the grip is mounted.
6
2.5 mm Remote Cable Socket
Accepts 2.5 mm shutter release cable.
7
Battery Tray Compartment
Houses the battery tray.
8
1/4"-20 Mounting Screw
Connects to the camera’s tripod
socket.
9
Power Contacts
Slide into the camera’s battery
chamber and transmit power.
10
Battery Tray
Secures Nikon EN-EL15a battery.
11
Battery Chamber Lock
Locks and unlocks the battery tray.
12
2.5 mm Shutter Release Cable
(BG-N6RC)
Transmits shutter release signal from
battery grip to the camera.
5
ASSEMBLY
OVERVIEW INTRODUCTION
Attaching the Grip
1.
Ensure that the camera
power is turned off.
2.
Turn the camera upside
down, and open the
camera’s battery chamber
door. Pull gently at a 45°
angle until the chamber door
detaches.
3.
Slide the camera battery
chamber door into the
BG-N18 chamber door
holder for safekeeping.
6
4.
Insert the BG-N18 grip
power contacts into the
camera’s battery chamber
as shown. Make sure to
align the camera’s tripod
socket with the BG-N18
mounting screw.
5.
Rotate the locking wheel
counterclockwise until it is
firmly tightened.
6.
Connect the shutter release
cable from the cable release
socket on the battery grip
to the remote release port
on the camera body.
7
OVERVIEW
ASSEMBLY
INTRODUCTION
Inserting Batteries
1.
Ensure that the power is
turned off on the camera.
2.
Flip out the battery tray lock
with your finger tip, and
rotate counterclockwise.
Slide the battery tray out
of the grip.
3. Line up the contacts on the
battery with the contacts
inside the battery tray, and
insert the battery.
8
When removing the grip, turn the camera power off and
remove the batteries.
4.
Insert the battery into the battery tray
compartment, and close and lock the tray.
9
OVERVIEW
ASSEMBLY
INTRODUCTION
Power Source Nikon EN-EL15a rechargeable battery
Operating Temperature 32°F to 104°F (0°C to 40°C)
Dimensions (H × D × W) 4 x 2.9 x 5.3 in. (10.2 x 7.5 x 13.5 cm)
Weight 6.2 oz. (175.8 g)
The shutter release button on the
battery grip is not triggering the
camera.
•
Make sure the 2.5 mm Shutter Release Cable is connected from the battery
grip to the camera.
Specifications
Troubleshooting
10
ONE-YEAR LIMITED WARRANTY
This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship
under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after
replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty
shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal
use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s)
shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves
the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper
installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER
ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty
provides you with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Vello Customer Service Department to obtain a return merchandise
authorization (“RMA”) number, and return the defective product to Vello along with the RMA number and proof of
purchase. Shipment of the defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.vellogear.com or call Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
VELLO is a registered trademark of the Gradus Group. © 2020 Gradus Group LLC. All Rights Reserved.
All other trademarks are the property of their respective owners.
GG2
www.vellogear.com
/
