KYOCERA CS 820 Operating instructions

Category
Print & Scan
Type
Operating instructions

This manual is also suitable for

Printing System (W)
Operation Guide
Set up Edition
i
Trademark Information
KPDL is a trademark of Kyocera Corporation.
Ethernet is a registered trademark of Xerox Corporation.
Novell and NetWare are registered trademarks of Novell, Inc.
Centronics is a trademark of Centronics Data Computer Corporation.
IBM and IBM PC/AT are trademarks of International Business Machines Corporation of
America.
PowerPC is a trademark of International Business Machines Corporation in the USA and other
countries.
Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated.
CompactFlash is a registered trademark of SanDisk Corporation.
PCL is a registered trademark of Hewlett-Packard Development Company in the USA.
All other company and product names contained in this Operation Guide are trademarks or
registered trademarks of their respective companies. The designations ™ and ® will not be used in
this Operation Guide.
About this Operation Guide
The Setup Edition of this Operation Guide is meant to be read when using this machine as a local
printer or a network printer by installing a printer board. This Operation Guide explains how to set up
this machine.
As the required set-up in order to use the printer as a scanner may differ depending upon the
environment in use in the connected computer, please read those sections related to your specific
computer environment and perform the appropriate set-up procedures explained there.
The Functions Edition of the Operation Guide explains how to perform printing, method of various
settings, and method of operating from a computer.
Using the Operation Guide (On-Line Manual)
The Operation Guide (On-Line Manual) is included in the supplied CD-ROM as a PDF (Portable
Document Format) file. To read the On-Line Manual, Adobe Reader or upper is needed.
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying, recording or by any information storage
and retrieval system, without permission in writing from the Publisher.
Legal Restriction On Copying
It may be prohibited to copy copyrighted material without permission of the copyright owner.
It is prohibited under any circumstances to copy domestic or foreign currencies.
Copying other items may be prohibited.
ii
Getting connected
For local connection of this machine (direct connection between a computer and the printer
through a parallel/USB cable)
For network connection of this machine (connection of the printer through a network)
<Example connection>
1
Page 4
Connect the computer and the printer
through a parallel cable or a USB cable.
2
Install the printer driver in the computer. (Refer to the
On-Line Manual.)
1
Page 5
Connect a network cable (100Base-TX,
10Base-T or the like) to the printer.
3
Install the printer driver in the computer. (Refer to the
On-Line Manual.)
2
Page 6
Perform the network (TCP/IP) setting on
the printer.
iii
Contents
1 Preparations ....................................................................................................... 1
Names of parts ............................................................................................................................1
Main body ..............................................................................................................................1
Operation panel .....................................................................................................................2
Accessories .................................................................................................................................3
Items to be prepared by user .......................................................................................................3
2 Set-up .................................................................................................................4
Connecting the printer cable ........................................................................................................4
Connecting the network cable .....................................................................................................5
Setting the network (TCP/IP) .......................................................................................................6
Installing the software ................................................................................................................10
3 Canceling printing ........................................................................................... 10
iv
1
1 Preparations
Names of parts
Main body
1 Memory card (CompactFlash) slot — Insert an optional memory card (CompactFlash) here.
You can write optional fonts, macros, and forms into the memory card. For details, refer to The
Functions Edition of the Operation Guide.
2 USB interface connector — USB interface based on USB2.0. Use a USB cable to connect to
a USB port of a computer.
3 Network interface connector — Use a 10Base-T/100Base-TX network cable to connect to a
network.
4 Parallel interface connector — Use a parallel cable to connect to a parallel port of a
computer.
5 Main power switch — When using this machine, turn on the main power switch. When
connecting a printer cable or the like, turn off this switch.
6 Operation panel — When performing setting on this machine, use the operation panel.
5
6
1
3
2
4
Preparations
2
Operation panel
1[Printer] key (indicator) — Press this key to light up when selecting the printer mode.
2 Status indicator — Lights up or blinks to show the status of this machine.
Lighting green: This machine is receiving data.
Lighting orange: An error that interrupts printing has occurred.
Blinking orange: An error that does not interrupt printing has occurred.
3 Touch panel — Displays the status of the printer and various keys for operation.
4 Keypad — Use these keys when you want to enter a desired value for one of the various
settings.
Touch panel in the printer mode
5 [Printer Menu] — Press this key to perform printer initial setting.
6 [Cancel] — Press this key to cancel printing or to cancel error display.
7 [GO] — Select this key to continue printing or to perform form feed. Also, use this key to switch
between on-line and off-line.
Mixed
Size originals
Printer
Menu
Cancel
Ready to print.
GO
324
1
Printer
Menu
Cancel
Ready to print.
GO
5 6 7
Preparations
3
Accessories
CD-ROM (Product Library)
Operation Guide
Items to be prepared by user
For parallel connection of the printer: Parallel cable (based on IEEE1284, shorter than 1.5 m)
For USB connection of the printer: USB2.0 compatible cable (based on High-Speed USB,
shorter than 5.0 m)
For network connection of the printer: Network cable (10Base-T or 100Base-TX)
NOTE: When using a USB, 10Base-T or 100Base-TX cable, prepare a shielded cable.
4
2 Set-up
Connecting the printer cable
When using this machine as a local printer, use a parallel cable or a USB cable as a printer cable to
connect this machine to a computer.
IMPORTANT:ALWAYS turn the main power switch of the machine OFF BEFORE connecting the
printer cable.
1
Turn the main power switch located on the rear left of
this machine OFF ( ). Also, turn off the power of the
computer to be connected.
2
Connect the printer cable to the parallel interface
connector or the USB interface connector located on
the rear right of this machine.
3
Connect the other side of the printer cable to the parallel interface or the USB interface of the
computer.
Set-up
5
4
Turn the main power switch of this machine ON ( | ).
For details on setting of each interface, refer to the
Functions Edition.
Connecting the network cable
When using this machine as a network printer, use a network cable (10Base-T or 100Base-TX) to
connect this machine to a network.
1
Turn the main power switch located on the rear left of
this machine OFF ( ).
2
Connect the network cable to the network interface
connector located on the rear right of this machine.
3
Connect the other side of the network cable to the hub (concentrator).
4
Turn the main power switch of this machine ON ( | ).
5
Perform the network setting.
For details, refer to Setting the network (TCP/IP) on page 2-6.
Set-up
6
Setting the network (TCP/IP)
When using this machine as a network printer, you must set the IP address of this machine.
NOTE:
The IP address that should be registered here will differ depending upon your environment.
Check with your network administrator BEFORE performing this setting.
If you are using a DHCP or BOOTP server to automatically configure the IP address, you will
not need to change the IP address because DHCP or BOOTP server configuration is already
enabled as the factory default setting.
To cancel the setting, press the [Stop/Clear] key.
1
Press the [Printer] key. The machine enters the printer
mode.
2
Press [Printer Menu].
3
Press [Interface].
4
Press [Network].
Printer
Menu
Cancel
Ready to print.
Printer menu
Print Sta-
tus Page
Inte rface
Emulation
Page Set
Print
Paper
OtherHard Disk
Select item.
Fo nt
Quality
Handling
Interface
NetWare
Parallel Network
Change #
Setting Item Value
On
TCP/IP On
Ethertalk On
Network Status Page Off
USB
Printer menu
Set-up
7
5
Press [] or [] to select TCP/IP and
press [Change #].
6
Press [On] located under TCP/IP.
7
Press [] or [] to select DHCP and
press [Change #].
8
Press [Off] and press [Close].
9
Press [] or [] to select BOOTP and
press [Change #].
10
Press [Off] and press [Close].
Interface
NetWare
Parallel Network
Change #
Setting Item Value
On
TCP/IP On
Ethertalk On
Network Status Page Off
USB
Printer menu
TCP/IP
Off
On
DHCP Off
BOOTP Off
IP Address 0. 0. 0. 0
Subnet Mask 0. 0. 0. 0
Gateway 0. 0. 0. 0
TCP/IP
Back
Setting Item Value
Printer menu - Interfac e - Network
Change #
Close
DHCP Off
B OOT P Off
IP Address 0. 0. 0. 0
Subnet Mask 0. 0. 0. 0
Gateway 0. 0. 0. 0
Back
Setting Item Value
Interface - Network
DHCP Setting
Off
On
Back
Printer menu -Interface -Network -TCP/IP
Change #
Close
DHCP Off
B OOT P Off
IP Address 0. 0. 0. 0
Subnet Mask 0. 0. 0. 0
Gateway 0. 0. 0. 0
Back
Setting Item Value
Interface - Network
BOOTP Setting
Off
On
Back
Printer menu -Interface -Network -TCP/IP
Set-up
8
11
Press [] or [] to select IP Address
and press [Change #].
12
Use the numeric keys on the keypad to
enter the address.Enter the 3-digit
address in the highlighted area and
press the [#] key.
Fix the entered address three digits at a
time by pressing the [#] key.
13
Enter the next 3-digit address and press
the [#] key.
To modify the entered address, press
the [#] key to select the 3-digit address
to be modified and use the numeric keys
to enter the address again.
14
Use the same procedure to enter the
remaining address and then press
[Close]. The display returns to the
TCP/IP screen.
If you press [Back], the entered address
is cleared and the previous address is
set again.
15
Press [] or [] to select Subnet Mask
and press [Change #].
16
Set the address using the same
procedure as IP address setting from
steps 12 to 14.
Change #
Close
DHCP Off
BOOTP Off
IP Address 0. 0. 0. 0
Subnet Mask 0. 0. 0. 0
Gateway 0. 0. 0. 0
Back
Setting Item Value
Interface - Network
IP Address
10
(with #key)
Back
Printer menu -Interface -Network -TCP/IP
000
Confirm per 3 lines pres s ing # key.
IP Address
10
(with #key)
Back
Printer menu -Interface -Network -TCP/IP
141 00
Confirm per 3 lines pres s ing # key.
Close
10
(with #key)
Back
Interface - Network - TCP/IP
141 110 204
s pressing # key.
Change #
Close
DHCP Off
BOOTP Off
IP A ddres s 10. 141. 110. 204
Subnet Mask 0. 0. 0. 0
Gateway 0. 0. 0. 0
Back
Setting Item Value
Interface - Network
Subnet Mas k
0
(with #key)
Back
Printer menu -Interface -Network -TCP/IP
000
Confirm per 3 lines pres s ing # key.
Set-up
9
17
Press [] or [] to select Gateway and
press [Change #].
18
Set the address using the same
procedure as IP address setting from
steps 12 to 14.
19
When all the setting is complete, press
[Close].
20
Press [Close].
21
Press [Close]. The display returns to the
printer mode.
Change #
Close
DHCP Off
B OOT P Off
IP Addres s 10. 141. 110. 204
Subnet Mask 255. 255. 255. 0
Gateway 0. 0. 0. 0
Back
Setting Item Value
Interface - Network
Gateway
0
(with #key)
Back
Printer menu -Interface -Network -TCP/IP
000
Confirm per 3 lines pres s ing # key.
Change #
Close
DHCP Off
B OOT P Off
IP Addres s 10. 141. 110. 204
Subnet Mask 255. 255. 255. 0
Gateway 10. 130. 112. 108
Back
Setting Item Value
Interface - Network
Network
Change #
Close
ting Item Value
On
On
On
s Page Off
USB
Close
tem.
Page Set
Print
Paper
OthersHard DiskFont
Quality
Handling
Canceling printing
10
Installing the software
Install the software such as printer driver according to your computer system. For the method of
installation, refer to the Printer Driver User Guide.
3 Canceling printing
To cancel printing and clear the data, perform the following procedure.
Press [Cancel].
In case that data is on processing, printing can be canceled on the printer screen.
1
Press the [Printer] key. The machine enters the printer
mode.
2
Press [Cancel].
3
Select the interface through which
printing to be canceled is performed.
To stop canceling printing, press [Stop].
Output
APS
A4 Plain
Count/Set
1 sided
Left tray
Cancel
rinting.
Cancel
user1
User name: user1 Job name:
Orig. Page
A4
16
Stop
Select interface to cancel the job.
Current
Job
NetworkParallel
Serial USB
Canceling printing
11
4
Printing is canceled.
Cancel
Canceling data.
Off line
User name: user1 Job name:
Orig. Page
A4
16
Canceling printing
12
First edition 2008. 11
Printed in Japan 303M156010
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

KYOCERA CS 820 Operating instructions

Category
Print & Scan
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI