International Concepts C01-2P Operating instructions

International Concepts
Brand
International Concepts
Model
C01-2P
Type
Operating instructions
Item
No.
:
C
-
2
REVISED JAN 11, 2012
Printed in Vietnam
- 1 -
Description
Item No.
:
: C-2
ASSEMBLY
INSTRUCTIONS
Item
No.
:
C
-
2
REVISED JAN 11, 2012
Printed in Vietnam
- 2 -
BEFORE ASSEM
B
LY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. Please take the time to read and follow the assembly instructions carefully.
Be sure to check all packing material carefully for small parts which may have come loose inside the carton
during shipment. Please separate, identify, and count all parts and metal hardware. Compare with part list to be
sure all parts are present.
If hardware is missing or you have difficulty assembling this product, please call Toll Free: 1-888-944-8396.
IMPORTANT NOTE:
- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
- Remove all wrapping material, including staples & packing straps before you start to assemble.
- DO NOT tighten all screws and bolts until completely assembled.
- Keep all hardware parts out of reach of children.
PART
LIST
When unpacking, please carefully not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Chair back 1
B Seat Frame 1
C Chair Seat 1
D
Front Leg
(L-R)
2
E
Side
Stretcher
2
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED
Item
No.
:
C
-
2
REVISED JAN 11, 2012
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please carefully not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1
Short bolt
( M6x40mm)
3
2
Medium bolt
(M6x60mm)
4
3
Long bolt
(M6x80mm)
4
4
Wood Screw
(M4x35mm)
8
5
Lock Washer
(Þ6.5x13mm)
11
6
Flat Washer
(Þ6.5X19mm)
11
7
Allen Key
(4mm)
1
STEP 1
Attach Seat Frame (B) to the Back (A) by using bolts (3) and (1), Washers (5) and (6) tighten with Allen
Key (7) as shown below.
Note: DO NOT tighten any of the bolts, until the chair is assembled, then put on a flat level surface to
make sure the chair is level and then tighten the bolts.
Item
No.
:
C
-
2
REVISED JAN 11, 2012
Printed in Vietnam
- 4 -
STEP 2
Attach Front Legs (D) to the seat frame (B) with bolts (2), Washers (5) and (6) .Tighten with Allen Key
(7).
Place Side Stretchers (E) between front and back legs, use the screwdriver to tighten the screws (4)
as shown below.
STEP 3
Attach the Seat (C) to top of the seat frame (from Step 2) by using Screws (4) ,tighten with a screw
driver.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

International Concepts C01-2P Operating instructions

International Concepts
Brand
International Concepts
Model
C01-2P
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents