Steel Core 43100 User manual

Steel Core
Brand
Steel Core
Model
43100
Type
User manual

Steel Core 43100 is a high-quality workbench designed for professional and home use. With a top shelf weight capacity of 250 lb. and a drawer weight capacity of 25 lb. per drawer, it can handle even the most demanding projects. The bottom shelf has a capacity of 200 lb., providing ample storage space for tools and materials. The 7" vise is perfect for holding workpieces securely, while the 2-1/2" thick table top provides a solid and stable work surface. Assembly is easy, and all necessary hardware is included.

Steel Core 43100 is a high-quality workbench designed for professional and home use. With a top shelf weight capacity of 250 lb. and a drawer weight capacity of 25 lb. per drawer, it can handle even the most demanding projects. The bottom shelf has a capacity of 200 lb., providing ample storage space for tools and materials. The 7" vise is perfect for holding workpieces securely, while the 2-1/2" thick table top provides a solid and stable work surface. Assembly is easy, and all necessary hardware is included.

*Actual product may vary slightly
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.
Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property
damage and/or personal injury. Please keep instructions for future reference.
For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.
For Customer Service, Call 1-800-348-5004
or e-mail [email protected]
43100 02/2017
60" 4 DRAWER HARDWOOD WORKBENCH
43100
[email protected]
2
1-800-348-5004
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
1. Do not exceed weight capacities for the Workbench shelves and drawers. Be aware of dynamic loading!
Sudden load movement may briefly create excess load causing product failure.
2. Use only on flat, level and hard surface capable of supporting the Workbench and any item(s) placed on Workbench.
Evenly distribute load on Table to avoid tipping.
3. Use as intended only. Do not use Workbench to perform task for which it was not designed.
4. For indoor use only.
5. Assemble only according to these instructions. Improper assembly can create hazards.
6. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
9. Do not assemble when tired or when under the influence of drugs or medication.
10. This product is not a toy. Do not allow children to play with, on or near Workbench.
11. Inspect before every use; do not use if parts are loose or damaged.
SPECIFICATIONS
Top Shelf Weight Capacity 250 lb.
Drawer Weight Capacity 25 lb. (per drawer)
Bottom Shelf Capacity 200 lb.
Vise Capacity 7"
Table Top Thickness 2-1/2"
[email protected]
3
1-800-348-5004
PARTS DIAGRAM
1. Table Top (1) 1pc 2. Shelf (2) 1pc 3. Cross Brace (3) 2pcs
4. Leg (4) 2pcs 5. Vise (5) 1pc 6. Ø80mm Screw (6) 6pcs
(Spar parts 2pcs)
7. Ø80mm Bolt (7) 8pcs 8. Connecting Nut (8) 8pcs
9. 80mm Hex Wrench (9) 1pc
(Spar parts 2pcs) (Spar parts 2pcs)
10. Wood Peg (10) 4pcs 11. Small Anvil Peg (11) 4pcs 12. Screw (12)
13. Screw(13) 62pcs 14. Silding Partition (14) 15. Lower Support (15)
Drawer Screws(22)
Drawer Panel - P3 (18) Drawer Back - P2 (17)
Drawer Slot Panel - P4 (19)
Drawer Bottom - P5 (20)
Drawer Front - P1 (16)
Drawer Handle(21)
[email protected]
4
1-800-348-5004
ASSEMBLY INSTRUCTIONS
Read the ENTIER IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.
1. NOTE: More than one person is needed for proper assembly.
2. NOTE: In the supplied bag of hardware, the Nuts are already threaded onto
the screw(6)
ASSEMBLY STEPS:
1. Insert Connecting Nuts (8) into holes at end of Cross Braces(3). Make Sure that
the slot on the Nuts align horizontally with the Bolts(7). This will allow the Bolts
to be threaded into the Cross Braces.
Cross Brace(3)
NOTE: Make sure the groove in the Cross Brace is facing IN.
Cross Brace (3)
Leg (4)
FRONT
[email protected]
5
1-800-348-5004
2. Once both Legs have Been fastened to the Cross Brace, slide the Shelf(2) above
against the legs so that the far edge fits onto the groove on the Cross Brace.
Shelf (2)
3. Insert Connecting Nuts (8) into holes at end of Cross Braces(3).
(as same as 1)
Cross Brace(3)
[email protected]
6
1-800-348-5004
4. Overturn Table Top (1), facing to FRONT, put Sliding Partition(14) dowel alignment
the holes, then tighten Screw(13), Don't lose any screws.
hold
14. Sliding Partition (14)
[email protected]
7
1-800-348-5004
5. Putting the PART 3 to PART 4. Using Ø80mm tighting Screw (6) .
Then installing Lower Support (15)
Lower Support (15)
[email protected]
8
1-800-348-5004
6. After that, overturn the workbench, as following picture
7. Installing the drawers
Drawer Handle(21)
[email protected]
9
1-800-348-5004
8. Putting the drawers into the slide rail
1 No teB efore installing, must do as picture A to slide the rail to the top part.
OK
Slide the rail to the top part
2P utting the drawers to the slide rail slowly, don't overexert
3 A fter assembly pictures
[email protected]
10
1-800-348-5004
9. Installing Vise(5) on the bench top.
10. Putting the Wood Peg(10) and Small Anvil Peg(11) into the holes on the bench top.
Finished
[email protected]
11
1-800-348-5004
Limited Manufacturer Warranty
FOT makes every effort to ensure that this product meets high quality and durability
standards. FOT warrants to the original retail consumer a 1-year limited warranty
from the date the product was purchased at retail and each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of
maintenance. FOT shall in no event be liable for death, injuries to persons or
property, or for incidental, special or consequential damages arising from the
use of our products. To receive service under warranty, the original manufacturer
part must be returned for examination by an authorized service center. Shipping
and handling charges may apply. If a defect is found, FOT will either repair or
replace the product at its discretion.
DO NOT RETURN TO STORE
For Customer Service:
Email: [email protected] or Call 1-800-348-5004
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Steel Core 43100 User manual

Steel Core
Brand
Steel Core
Model
43100
Type
User manual

Steel Core 43100 is a high-quality workbench designed for professional and home use. With a top shelf weight capacity of 250 lb. and a drawer weight capacity of 25 lb. per drawer, it can handle even the most demanding projects. The bottom shelf has a capacity of 200 lb., providing ample storage space for tools and materials. The 7" vise is perfect for holding workpieces securely, while the 2-1/2" thick table top provides a solid and stable work surface. Assembly is easy, and all necessary hardware is included.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents