Delaney 301676 Installation guide

Brand: Delaney

Model: 301676

Type: Installation guide

This manual is also suitable for

USER MANUAL

TEMPLATE

45 40 35

1-3/4" 1-9/16" 1-3/8"

Fit here on door edge

FOR BACKSET 70mm (2-3/4”)

FOR BACKSET 60mm (2-3/8”)

Mark Ø1" (25.4mm) hole at

center of door edge.

Ø54mm (2-1/8")

Attention : Please do not use the "electronic" screwdriver for installation.

Product :

Purchase Date :

Limited Warranty Statements

1. Warranty

The manufacturer warrants the Product to be free

from defects in material and workmanship for a period of 12 months

from the original date of purchase.

If you discover a defect in the Product covered by this warranty, we will repair or

replace the item at our option using new or refurbished components.

2. Exclusions

This warranty covers defects in manufacturing discovered while using the

Products as recommended by The manufacturer rather than occurred by the act

of God, and damages caused by misuse, abuse, and unauthorized modification.

3. Limited of Liability

The manufacturer will not be held liable for incidental or consequential losses or

damages to any act of God.

4. Reminder

Service requirement shall subject to the presentation of this warranty card

and defective parts to the manufacturer.

The warranty card will not be reissued if lost.

TOUCHPAD

ELECTRONIC DEADBOLT LOCK

PACKAGE CONTENTS

PART

DESCRIPTION

QUANTITY

Key

Cylinder

Deadbolt pad AssemblyTouch

Deadbolt Latch

Strike Plate

Mounting Plate

Receiver Assembly

Battery Cover

Drive-in Sleeve

Machine Screws

Wood Screws

Deadbolt Chassis Screws

Machine Screws

Qty. 3

Wood Screws

Qty. 5

Deadbolt Chassis Screws Qty. 2

J K

HARDWARE SCREWS CONTENTS

LATCH BACKSET ADJUSTMENT

Remarks:

Please notice the the latch box between two different backsets.slight differences in

180°

2 3/4" (70 mm)2 3/8" (60 mm)

70 mm

60 mm

2.1

1. Backset Determination

Backset is a distance from door edge to

centre of hole on door face.

Adjustable latch fits both backset of

2 3/8" (60 mm) and 2 3/4" (70 mm).

2. Change Latch Face

Determine which latch mounting method will

be used and make necessary adjustments.

No adjustment required for square latch

face plate.

a. Use a flat screwdriver to separate the

face plate.

b. Snap selected latch face plate onto back

plate.

Drive-in Latch

Drive-in Installation

Remove original latch faceplate.

Align the (I) as illustrated and

snap into the latch case.

drive-in sleeve

ASSEMBLY INSTRUCTIONS

2 3/4" (70 mm)

3. Latch Backset Adjustment

Determine if the latch (D) needs to be adjusted

to the 2 3/4" (70 mm) backset.

To adjust, rotate the latch until it stops.

Reverse the direction to return to the

2 3/8" (60 mm) backset.

4. Mark the Door with Template

Select the height and backset as desired on

the door face; use the TEMPLATE as an

indication to mark the centre of the circle on

the door face and the centre of the door

edge.

5. Drill Holes

Using the marks as a guide to drill a hole

Ø2 1/8" (54 mm) through the door face for

the lockset, then a hole of Ø1" (25.4 mm)

for latch.

ASSEMBLY INSTRUCTIONS

6. Mark the Outline of Latch Faceplate

Insert the latch (D) and ensure it is parallel to

the door face.

Mark the outline of the faceplate, then

take out the latch (D).

7. Chisel Space for Latch Faceplate

Chisel 5/32" (4 mm) deep along the outline

to allow the faceplate to be aligned with

the door edge.

Note: It is not necessary to chisel the door

edge for the faceplate installation if

you use the drive-in latch.

8. Install Latch

Insert the latch (D) into the door.

(Make sure the cross is on the bottom of the

latch.) Use 2 wood screws (K) to secure latch.

Please do not fully tighten the screws until

lock is completely installed.

Hardware Used

K Wood screws x2

ASSEMBLY INSTRUCTIONS

You need to stay

this way up when

inserting the latch.

Make sure the cross in the

latch is on the bottom.

8.1

Install Drive-in Latch

Drive the latch (D) into the hole on edge of

door.

9. Mark the Outline of Strike

To identify the centre of strike: close the

door to lay the latchbolt against the door

frame. Mark the centre line on the doorframe

exactly opposite the latch hole in the door

edge.

10.1 Drill Hole on Door Frame

Measure one half of door thickness from door

stop and vertically mark centre line of strike.

Drill 1" (25.4 mm) hole, 1" (25.4 mm)

deep at intersection of horizontal and vertical

line of strike.

10.2 Chisel Space for Strike

Chisel 5/64" (2 mm) deep along the strike

outline to allow the strike to be aligned with

the doorframe.

ASSEMBLY INSTRUCTIONS

11. Install Strike on Door Frame

Install the strike plate (E) into your door frame

and tighten with wood screws (K).

12. Install Touchpad Assembly

Make sure the latch bolt is retracted.

13. Install AssemblyTouchpad

touchpadInstall cylinder (B) into the deadbolt

assembly (C) with tailpiece in horizontal

position inserted through hub of the latch.

ASSEMBLY INSTRUCTIONS

Hardware Used

K Wood screws x2

horizontal position

Left-handed Right-handed

Hardware Used

Deadbolt chassis screws x2

14. Install Assembly

Pass the IC wire under the latch (D) to the

interior side of the door, and insert the

tailpiece through the cross-shaped crank

of the latch

Touchpad

15. Install Inside Mounting Plate

Pass the IC wire through the wire hole of the

mounting plate (F). Fix the mounting plate (F)

with screws (L). If outside lock assembly is

lopsided, please loosen the screws to adjust

its position and tighten the screws again.

16. Identify Door Handing

Face the door from the outside. The

door is left-handed if the hinges are

on the left side of the door, whereas

the door is right-handed if the hinges

are on the right side of the door.

ASSEMBLY INSTRUCTIONS

Hinge Hinge

horizontal position

IC wire

Hardware Used

For right-handed

door

For left-handed

door

17. Adjust Thumb Turn Piece

Rotate the thumb turn piece to the LEFT at

45 degrees for right-handed doors.

Rotate the thumb turn piece to the RIGHT at

45 degrees for left-handed doors.

18. Install Receiver Module

Remove the battery cover (H)

(push it up first then pull it out).

19. Install Receiver Module

Connect the IC wire into the back of the

receiver module. Ensure that the deadbolt

tailpiece is engaged with turn piece, then

attach receiver module (G) to the door with

screw (J). Use the optional wood screw (K)

to secure the receiver module to wood doors

only.

Machine screws x3

H G

ASSEMBLY INSTRUCTIONS





K Wood screw x1

This screw is optional. It may not be necessary to

use this screw.

20. Insert Batteries

Insert 4 (AA) 1.5 V alkaline batteries and

slide the battery cover (H) back onto the

receiver module (G).

Remarks:

(1) Alkaline batteries are recommended in

order to stabilize the power supply. If you

don't use alkaline, battery performance

will be reduced greatly.

(2) All settings will be retained in the memory

even if the batteries are completed dead.

G H

ASSEMBLY INSTRUCTIONS















 Programming Button

Programming button is for setting function.



 Cylinder

To lock/unlock the lockset from outside.

 Washer

Prevents water from permeating into lockset.

 Battery Lid

Slide the lid to change the batteries.

 Battery Holder

Four AA (1.5 V) alkaline batteries.

 R Button (Reset)

Restore default settings.

 Turn-piece

To lock/unlock the lockset from inside.

Lock Btutton

Lock Button is for lock and unlock function

by key

OPERATIONAL INTERFACE



Keep the door open while programming to avoid being locked out

accidentally. The lock contains one factory-preset user code but can be

programmed to store up to a total of six additional unique user codes.

˙ Codes can be added and deleted at any time. For first-time programming,

use factory default programming code. It’s recommended to change the

default programming code and default user code right after you install

the lock.

Every programming step should be done within 6 seconds.

OPERATING INSTRUCTIONS

Operation Indicator Sounds and Lights

Sounds

Lights Meaning

Successful Operation

Successful Programming

Operation Error

Code Input Error;

System Shuts Down

Low Battery Power

Default Setting Restored

In Programming Mode

1 Beep

2 Long Beeps

3 Beeps

5 Beeps

10 Rapid Beeps

Lock button flashes slowly

3 Long Beeps

3. Add New User Code

Note:

4–10 digits in length.

Up to 30 sets of user codes can be saved. User codes should be

OPERATING INSTRUCTIONS

2. Change Programming Code

4. Delete an Existing User Code

5. Delete All User Codes at Once

Note:

user codes are deleted.

The lock can only be operated by key during that time.

Auto-locking and keypad locking functions will be invalid when

Default programming code (PC): 0000

Default user code (UC): 1234

Your new programming code (PC) ____________

Your new user code (UC) ___________________

The same programming code and user code cannot be accepted.

The lock will cease operation if unauthorized codes are entered

over 5 times. The system will unfreeze after 45 seconds.

DO THIS FIRST

1. Door Handling Identification Process

The lock needs to learn if your door is a right- or left-handed .

Enter PC

Enter

New PC

Enter PC

Enter

New UC

Enter PC

Enter

the UC you

want to

delete

Enter PC

OPERATING INSTRUCTIONS

8. Enable/Disable All User Codes

Note:

user codes are disabled. The lock can only be operated by key

during the time. Repeat the steps to enable the user codes again.

Auto-locking and keypad locking functions will be invalid when

9. Create a One-Time User Code 4–10 Digits Long

Note: The one-time user code will automatically cancel after it is used

one time.

6. Toggle Auto-Lock On/Off

Note:

following instructions #7.

Repeat the steps in #6 to cancel the auto-locking function.

The preset delay-time is 30 seconds, you can change the time by

7. Set Auto-Lock Time Delay

Note: 10–99 seconds delay-time available.

Enter PC

Enter

Seconds

(10~99)

Enter PC

Enter

One Time

Code

OPERATING INSTRUCTIONS

10. Restore Default Settings

Press

Note: Press the button for more than 5 seconds;

the programming is reset back to the original

factory codes once you hear 3 long beeps.

After restoring default settings, you must run

the door handing identifying process (#1)

again before programming any other

functions.

Reset

button

WARRANTY

CARE AND MAINTENANCE

Do not use any chemical liquid or lubricating oil with additives to clean the

lock body. It will damage the surface or even mainboard.

The manufacturer warrants the product to be free from defects in material

and workmanship for a period of 12 months from the original date of

purchase. If you discover a defect in the product covered by this warranty,

we will repair or replace the item at our option using new or refurbished

components.

EXCLUSIONS

This warranty covers defects in manufacturing discovered while using the

products as recommended by the manufacturer rather than occurred by

the act of God, and damages caused by misuse, abuse, and unauthorized

modification.

LIMITED LIABILITY

The manufacturer will not be held liable for incidental or consequential

losses or damages from any act of God.

After installing the lockset

and batteries, the door

can’t be locked and three

short beeps are emitted

when you press the

lock button.

The door-handing

identification process

isn’t yet complete.

Refer to step1, page13.

You’ve installed the

lockset and batteries, but

you still get no response

when you press any

button.

Batteries were installed

incorrectly and cable

connect incorrectly.

Check to see if the battery

polarities have been

reversed or if the battery is

dead. If so, re-install or

change the battery. If not,

please check to see if the

cable is properly

connected.

When you are in the

door-handing identifying

process, you hear three

times, and three short

beeps.

Wrong door-handing or

change of the

door-handing in the

memory.

Press the R button to

restore the system to

factory default setting and

re-execute door-handing

identifying process

(step 1, page 13)

Although you succeeded

in the first execution of

the door-handing

identifying process, the

latch still doesn’t work.

(i.e. You can feel the motor

attempting to run.)

Low battery.

Replace with new alkaline

batteries.

PROBLEM

POSSIBLE CAUSE CORRECTIVE ACTION

TROUBLESHOOTING

The door can be locked

normally, but when you try to

unlock it, you hear three short

beeps and the lock won't

unlock when you enter the

user code and press the

lock button.

The functioning of the

micro-switch is abnormal.

Call our customer

service department

While the door is locked, you

hear the latch bolt coming out

when you press the

lock button to lock the door;

however, three short beeps

are emitted.

Conversely, while the door is

open, no beeps are emitted

when locking the latch bolt.

(1) The depth of the latch

bolt hole is insufficient.

(2) The latch bolt is not

aimed at the opening

of the strike.

(1) Dig the latch bolt hole

for the strike

(2) Adjust the strike to the

appropriate position.

deeper.

The minimum depth is

1" (2.5 cm).

PROBLEM

POSSIBLE CAUSE CORRECTIVE ACTION

TROUBLESHOOTING

Delaney 301676 Installation guide

Brand: Delaney

Model: 301676

Type: Installation guide

This manual is also suitable for

Download PDF

report

Delaney 301676 Installation guide

This manual is also suitable for

Delaney 301676 Installation guide

Related papers

Other documents