Toro 74778 Installation guide

Type
Installation guide

This manual is also suitable for

FormNo.3420-276RevA
TimeCutter
®
RidingMowers
ForTimeCutter
®
RidingMowerswithMyRide
®
Suspension
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
Backcushion1
1
Flanged-hexbolt3
Installthebackcushion(machineswith
a60-inchdeckshippedinasteelcrate
only).
Pin1
2
Roundclip2
InstalltheMyRidesuspension.
3
Nopartsrequired
Connectthebattery.
4
Nopartsrequired
Installtheseat(machineswithMyRide
suspensionandshippedinawoodcrate
only).
Rearhitch1
Bolt(5/16x1inch)
2
5
Locknut(5/16inch)
2
Installtherearhitch.
6
Nopartsrequired
Setupthemotion-controllevers.
7
Nopartsrequired
Checkthemoweradjustment.
Ignitionkey1
Hosecoupling(notincludedwithCE
models)
1
Operator'sManual
1
Engineowner’smanual(non-Toro
engines)
1
8
Operatortrainingmaterial
1
Completingthesetup.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
©2017—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3420-276*A
1
InstallingtheBackCushion
Machineswitha60-InchDeck
ShippedinaSteelCrateOnly
Partsneededforthisprocedure:
1Backcushion
3Flanged-hexbolt
Procedure
1.Liftuptheseatontothesprings.
2.Installthebackcushionusingthe3anged-hex
bolts(Figure1).
g211172
Figure1
1.Backcushion
2.Flanged-hexbolt(3)
2
InstallingtheMyRide
®
Suspension
MachineswithMyRideSuspension
andShippedinaWoodCrateOnly
Partsneededforthisprocedure:
1Pin
2Roundclip
Procedure
1.Raisetheplatformandremovethewooden
blockfromabovethebattery.
Note:Youcandiscardthewoodenblock.
2.Rotatethesuspensionup(Figure2).
g233946
Figure2
3.Placetheendsofthespringsontheposts
(Figure3).
4.Securethespringstothepostswiththe2round
clips(Figure3).
5.Installthepinintothebackbyusingtheindexed
keyslot(Figure3).
2
g233947
Figure3
1.Pin4.Roundclip
2.Post
5.Shapeofthekeyslot
3.Spring
3
ConnectingtheBattery
NoPartsRequired
Procedure
WARNING
CALIFORNIA
Proposition65Warning
Batteryposts,terminals,andrelated
accessoriescontainleadandlead
compounds,chemicalsknownto
theStateofCaliforniatocause
cancerandreproductiveharm.Wash
handsafterhandling.
1.Locatethebatteryandnegativebatterycable.
2.Removetheplasticcapfromthenegative
batterypost.
3.Removethefastenersonthenegativebattery
cable,andusethemtosecurethenegative
batterycabletothenegativebatterypost(Figure
4).
g018395
Figure4
1.Negativebatterycable4.Negativebatterypostcap
2.Wingnut
5.Carriagebolt
3.Washer6.Negativebatterypost
3
4
InstallingtheSeat
MachineswithMyRideSuspension
andShippedinaWoodCrateOnly
NoPartsRequired
Procedure
1.Removethe2hairpincottersfromtheseat-pivot
rod,andremovetheseat-pivotrodfromthe
platform(Figure5).
g233956
Figure5
1.Hairpincotter
2.Seat-pivotrod
2.Placetheseatassemblyontotheplatform
(Figure6).
g233955
Figure6
3.Installtheseat-pivotrodbyinsertingtherod
fromthecenterandoutwardthroughthepivot
bracketholeandseatpanhole(Figure7).
Note:Ensurethattheseatpanisbetweenthe
2pivotbrackets.
g233952
Figure7
4
4.Installahairpincotteron1sideoftheseat-pivot
rod,thenslidetheseat-pivotrodthroughthe
pivotbracketholeandseatpanhole(Figure8).
g233953
Figure8
5.Installtheotherhairpincotterontheotherside
oftheseat-pivotrod(Figure9).
g233954
Figure9
6.Rotatetheseatassemblyupwardandconnect
thewireharnesstotheseatswitchonthe
bottomoftheseat(Figure10).
g233951
Figure10
1.Seatswitch
5
InstallingtheRearHitch
Partsneededforthisprocedure:
1Rearhitch
2
Bolt(5/16x1inch)
2
Locknut(5/16inch)
Procedure
InstallthebrackettotheframeasshowninFigure11
andFigure12.
g015397
Figure11
Beforeassembly
1.Bolts2.Locknuts
g015398
Figure12
Afterassembly
5
6
SettingUpthe
Motion-ControlLevers
NoPartsRequired
Procedure
1.Locatethemotion-controlleversattached,but
foldeddownonthemachine.
2.Removetheupperbolt(3/8x1inch)and
washer;loosenthelowerbolt(3/8x1inch).
3.Raisethemotioncontrolleverstotheupright
position.
4.Aligntheholesinthemotion-controlleverwith
theholesinthecontrol-armshaft,andinstallthe
boltandwasherremovedpreviously.Repeat
thisforbothcontrollevers.
Note:Handtightenallfasteners.
5.Movethemotion-controlleverstothepark
position,raisetheseat,andmovethecontrol
leversbacktothecenterposition(neutral).
6.Verifythatthemotion-controlleversareproperly
aligned.
Note:Adjustasnecessary.Tightenall
fasteners.
7
CheckingtheMower
Adjustment
NoPartsRequired
Procedure
Adjusttheside-to-sidelevelandthefront-to-rearblade
slope.UsetherelevantproceduresintheOperator's
Manualtoverifythatthedeckislevel,andmakeany
adjustmentsasnecessary.RefertotheOperator's
Manualformoreinformation.
8
CompletingtheSetup
Partsneededforthisprocedure:
1Ignitionkey
1
Hosecoupling(notincludedwithCEmodels)
1
Operator'sManual
1
Engineowner’smanual(non-Toroengines)
1
Operatortrainingmaterial
CheckingtheTirePressure
Checkthefrontandreartiresforproperination;
refertoCheckingtheTirePressureintheOperator’s
Manualfortherecommendedinationpressure.
CheckingtheSide-Discharge
Chute
Removethepackingrestraintholdingtheside
dischargechuteupandlowerthechuteintoplace.
CheckingtheEngine-OilLevel
Beforeyoustarttheengineandusethemachine,
checktheoillevelintheenginecrankcase;referto
CheckingtheOilLevelintheOperator'sManual.
OrganizingtheMaterial
Keepallthefollowingitemswiththemachine:
Ignitionkey
Hosecoupling(notincludedinCEmodels)
Operator'sManual
Engineowners’smanual(non-T oroengines)
Viewtheoperatortrainingmaterialbefore
operatingthemachine.
6
Notes:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Toro 74778 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI