Danfoss BTD RO MIX Operating instructions

Brand: Danfoss

Model: BTD RO MIX

Type: Operating instructions

Danfoss BTD RO MIX is a district heating substation for direct heating with tank for domestic hot water preparation and with thermostatic or electronic control. It is designed for floor-mounting with connections at the top.

Features of the Danfoss BTD RO MIX:

Pre-fabricated with a differential pressure controller, fitting piece and sensor pockets for insertion of heat meter as well as strainer and ball valves.
Mixing loop including pump, controls and non-return valve.
Heating circuit for direct generation of heat. The differential pressure control sets the optimal operation conditions for radiator thermostatic valves in order to enable individual temperature control in each room.

Features of the Danfoss BTD RO MIX:

Pre-fabricated with a differential pressure controller, fitting piece and sensor pockets for insertion of heat meter as well as strainer and ball valves.
Mixing loop including pump, controls and non-return valve.
Heating circuit for direct generation of heat. The differential pressure control sets the optimal operation conditions for radiator thermostatic valves in order to enable individual temperature control in each room.

OperatingGuide

TermixBTDROMIX

1.0TableofContents

1.0TableofContents.............................................1

2.0Functionaldescription......................................2

3.0Safetynotes.....................................................3

3.1SafetyNotes–general............................................3

4.0Mounting........................................................4

4.1Mounting...........................................................4

4.2Start-up..............................................................6

4.3Electricalconnections.............................................7

5.0Design.............................................................8

5.1Design...............................................................8

5.2Schematicdiagram................................................9

6.0Controls..........................................................10

6.1Heatingcircuit......................................................10

6.2DHWtemperaturecontrol........................................13

6.3Other.................................................................14

6.4Maintenance........................................................16

7.0Troubleshooting..............................................17

7.1Troubleshootingingeneral......................................17

7.2TroubleshootingDHW............................................17

7.3TroubleshootingHE...............................................18

7.4Disposal.............................................................19

8.0Declaration......................................................23

8.1Declarationofconformity........................................23

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

2.0Functionaldescription

Districtheatingsubstationfordirectheatingwithtankfor

domestichotwaterpreparationandwiththermostaticor

electroniccontrol.Designedforoor-mounting.Connections

atthetopofthestation.

Application

TheTermixBTDROMIXsubstationisacompletesolutionforhot

waterandheatingsystemwithdifferentialpressurecontroland

mixingloop.TheTermixBTDROMIXisapplicableforsingle-family

housesorapartments.

Districtheating(DH)

Thesubstationisprefabricatedwithadifferentialpressure

controller,ttingpieceandsensorpocketsforinsertionofa

heatmeteraswellasstrainerandballvalves.Furthermorethe

substationisdeliveredwithamixingloopincludingpump,controls

andnon-returnvalve.

Heating(HE)

Theheatingcircuitisdesignedfordirectgenerationofheat.The

differentialpressurecontrolsetstheoptimaloperationconditions

forradiatorthermostaticvalvesinordertoenableindividual

temperaturecontrolineachroom.Themixingloopcreatesa

suitabletemperaturelevele.g.foroorheating.

Domestichotwater(DHW)

Thedomestichotwatercircuitconsistsofahotwatertankwithcoil

andaself-actingthermostaticcontrolvalveorelectroniccontroller.

Thehotwatertankandcoilareenamelledandthetankcontainsa

magnesiumanode.

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

3.0Safetynotes

3.1SafetyNotes–general

Thefollowinginstructionsrefertothestandarddesignof

substation.Specialversionsofsubstationsareavailableon

request.

Thisoperatingmanualshouldbereadcarefullybeforeinstallation

andstart-upofthesubstation.Themanufactureracceptsno

liabilityfordamageorfaultsthatresultfromnon-compliancewith

theoperatingmanual.Pleasereadandfollowalltheinstructions

carefullytopreventaccidents,injuryanddamagetoproperty.

Assembly,start-upandmaintenanceworkmustbeperformedby

qualiedandauthorizedpersonnelonly.

Pleasecomplywiththeinstructionsissuedbythesystem

manufacturerorsystemoperator.

Corrosionprotection

Allpipesandcomponentsaremadeofstainlesssteelandbrass.

Themaximumchloridecompoundsoftheowmediumshouldnot

behigherthan150mg/l.

Theriskofequipmentcorrosionincreasesconsiderablyifthe

recommendedlevelofpermissiblechloridecompoundsis

exceeded.

Energysource

Thesubstationisdesignedfordistrictheatingastheprimary

sourceofenergy.However,alsootherenergysourcescanbeused

wheretheoperatingconditionsallowitandalwaysarecomparable

todistrictheating.

Application

Thesubstationisdesignedtobeconnectedtothehouse

installationinafrost-freeroom,wherethetemperaturedoesnot

exceed50°Candthehumiditydoesnotexceed60%.Donotcover

orwallupthesubstationorinanyotherwayblocktheentrance

tothestation.

Choiceofmaterial

Choiceofmaterialsalwaysincompliancewithlocallegislation.

Safetyvalve(s)

Werecommendmountingofsafetyvalve(s),however,alwaysin

compliancewithlocalregulations.

Connection

Thesubstationmustbeequippedwithfeaturesthatensurethat

thesubstationcanbeseparatedfromallenergysources(also

powersupply).

Emergency

Incaseofdangeroraccidents-re,leaksorotherdangerous

circumstances-interruptallenergysourcestothestationif

possible,andseekexperthelp.

Incaseofdiscolouredorbad-smellingdomestichotwater,closeall

shut-offvalvesonthesubstation,informtheoperatingpersonnel

andcallforexperthelpimmediately.

Storage

Anystorageofthesubstationwhichmaybenecessarypriorto

installationshouldbeinconditionswhicharedryandheated.

Authorizedpersonnelonly

Assembly,start-upandmaintenanceworkmustbeperformedby

qualiedandauthorizedpersonnelonly.

Pleaseobserveinstructionscarefully

Toavoidinjurytopersonsanddamagetothedevice,itisabsolutely

necessarytoreadandobservetheseinstructionscarefully.

Warningofhighpressureandtemperature

Beawareoftheinstallation’spermissiblesystempressureand

temperature.

Themaximumtemperatureoftheowmediuminthesubstationis

120°C.

Themaximumoperatingpressureofthesubstationis10bar.PN16

versionsareavailableonenquiry.

Theriskofpersonsbeinginjuredandequipmentdamagedincreases

considerablyiftherecommendedpermissibleoperatingparameters

areexceeded.

Thesubstationinstallationmustbeequippedwithsafetyvalves,

however,alwaysinaccordancewithlocalregulations.

Warningofhotsurface

Thesubstationhasgothotsurfaces,whichcancauseskinburns.

Pleasebeextremelycautiousincloseproximitytothesubstation.

Powerfailurecanresultinthemotorvalvesbeingstuckinopen

position.Thesurfacesofthesubstationcangethot,whichcancause

skinburns.Theballvalvesondistrictheatingsupplyandreturnshould

beclosed.

Warningoftransportdamage

Beforesubstationinstallation,pleasemakesurethatthesubstation

hasnotbeendamagedduringtransport.

IMPORTANT-Tighteningofconnections

Duetovibrationsduringtransportallangeconnections,screwjoints

andelectricalclampandscrewconnectionsmustbecheckedand

tightenedbeforewaterisaddedtothesystem.Afterwaterhasbeen

addedtothesystemandthesystemhasbeenputintooperation,

re-tightenALLconnections.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

4.0Mounting

4.1Mounting

Installationmustbeincompliancewithlocalstandardsand

regulations.

Districtheating(DH)-Inthefollowingsections,DHreferstothe

heatsourcewhichsuppliesthesubstations.Avarietyofenergy

sources,suchasoil,gasorsolarpower,couldbeusedasthe

primarysupplytoDanfosssubstations.Forthesakeofsimplicity,

DHcanbetakentomeantheprimarysupply.

Connections:

1.DHWcirculation(HWC)

2.Domestichotwater(DHW)

3.Domesticcoldwater(DCW)

4.Heating(HE)return

5.Heating(HE)supply

6.Districtheating(DH)return

7.Districtheating(DH)supply

Connectionsizes:

Allconnections:

G¾”(int.thread)

Dimensions(mm):

Withcover:

H1570xW540xD640(typeBTD-MIX1)

H1870xW540xD640(typeBTD-MIX2)

Weight(approx.):90-130kg

Authorizedpersonnelonly

Assembly,start-upandmaintenanceworkmustbeperformedby

qualiedandauthorizedpersonnelonly.

Thepipeplacementcandeviatefromtheshowndrawing.Pleasenote

themarkingsonthestation.

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

4.1.1Installation

Mounting:

Adequatespace

Pleaseallowadequatespacearoundthesubstationformounting

andmaintenancepurposes.

Orientation

Thestationmustbemountedsothatcomponents,keyholes

andlabelsareplacedcorrectly.Ifyouwishtomountthestation

differentlypleasecontactyoursupplier.

Drillings

Wheresubstationsaretobewall-mounted,drillingsareprovided

inthebackmountingplate.Floormountedunitshavesupport.

Labelling

Eachconnectiononthesubstationislabelled.

Beforeinstallation:

Cleanandrinse

Priortoinstallation,allsubstationpipesandconnectionsshouldbe

cleanedandrinsed.

Tightening

Duetovibrationduringtransport,allsubstationconnectionsmust

becheckedandtightenedbeforeinstallation.

Unusedconnections

Unusedconnectionsandshut-offvalvesmustbesealedwitha

plug.Shouldtheplugsrequireremoval,thismustonlybedoneby

anauthorizedservicetechnician.

Installation:

Strainer

Ifastrainerissuppliedwiththestationitmustbettedaccording

toschematicdiagram.Pleasenotethatthestrainermaybe

suppliedloose.

Connections

Internalinstallationanddistrictheatingpipesconnectionsmustbe

madeusingthreaded,angedorweldedconnections.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

4.2Start-up

Start-up,Heatingwithmixingloop

Start-up:

1:Pumpspeed

Setthepumptohighestspeedbeforestart-up.

2:Startpump

Startthepumpandheatthroughthesystem.

3:Openshut-offvalves

Theshut-offvalvesshouldthenbeopenedandtheunitobserved

asitentersservice.Visualcheckingshouldconrmtemperatures,

pressures,acceptablethermalexpansionandabsenceofleakage.

Ifthesystemoperatesinaccordancewithdesign,itcanbeput

toregularuse.

4:Ventsystem

Switchoffthepumpandventtheinstallationaftertheradiators

havebeenwarmedup.

5:Adjustpumpspeed

Setthepumptothelowestspeedconsistentwithcomfortand

electricityconsumption.

Normallythechange-overswitchissetinthemidposition(default).

Howeverforsystemswithunderoorheatingorsinglepipeloop

systems,itmaybenecessarytoturnthechange-overswitch

upwards.

Higherpumpspeedsareonlyusediftheheatingrequirement

increases.

Re-thightenconnections

Afterwaterhasbeenaddedtothesystemandthesystemhasbeen

putintooperation,re-tightenALLconnections.

Pump

Thepumpmustbeswitchedoffduringsystemll.

Underoorheating:

Pumpstopfunction

Ifthesubstationisusedinconnectionwithunderoorheating,the

circulationpumpmustbeconnectedtothepumpstopfunctionin

theunderoorheatingcontroller.Thepumpmustbestoppedif

allunderoorheatingcircuitsareclosed.

Warranty

Ifthisisnotpossible,thenowmustbecontinuedthroughthe

by-pass.Failingthis,thepumpwillbeatriskofseizureandany

remainingwarrantywillbewithdrawn.

Summeroperation:

Switchoffpump

Insummerthecirculationpumpmustbeswitchedoffandthe

shut-offvalvetoHEsupplyclosed.

Runningpumpbi-weekly

Itisrecommendedtostartupthecirculationpump(for2minutes)

onceamonthduringsummer;theshut-offvalveoftheHEsupply

mustbeshut.

Electroniccontroller

Mostelectroniccontrollerswillstartupthepumpautomatically

(pleasenotemanufacturer´sinstructions).

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

4.3Electricalconnections

Beforemakingelectricalconnections,pleasenotethe

following:

Safetynotes

Pleasereadtherelevantpartsofthesafetynotes.

230V

Thesubstationmustbeconnectedto230VACandearth.

Potentialbonding

Potentialbondingshouldbecarriedoutaccording

to60364-4-41:2007andIEC60364-5-54:2011.

Bondingpointonthemountingplatebelowrightcornermarked

withearthsymbol.

Disconnection

Thesubstationmustbeelectricallyconnectedsothatitcanbe

disconnectedforrepairs.

Outdoortemperaturesensor

Outdoorsensorsshouldbemountedsoastoavoidexposureto

directsunlight.Theyshouldnotbeplacedclosetodoors,windows

orventilationoutlets.

Theoutdoorsensormustbeconnectedtothestationonthe

terminalblockundertheelectroniccontrol.

Authorizedelectrician

Electricalconnectionsmustbemadebyanauthorizedelectricianonly.

Localstandards

Electricalconnectionsmustbemadeinaccordancewithcurrent

regulationsandlocalstandards.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

5.0Design

5.1Design

Yoursubstationmightlookdifferentthanthesubstationshown.

Designdescription

Hotwatertankwithcoil

Circulatorpump

Actuator,HE

Ballvalve,DVGW

Sensorpocket,energymeter

Fittingpiece,energymeter

Thermostaticvalve,DHW

Filling/drainvalve

Ballvalveclosed

Strainer

Testconnection

Diff.pressurecontrollerwithowlimiter

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

5.2Schematicdiagram

DHW

DCW

HWC

Supply

Return

Yoursubstationmightlookdifferentthantheschematicdiagramshown.

Schematicdescription

Hotwatertankwithcoil

Circulatorpump

Deliveredloosewithunit

Electroniccontroller

Sensorpocket,energymeter

Actuator,HE

Ballvalve

Outdoorsensor

2-waymotorizedvalve

Ballvalve,DVGW

Thermometer

Fittingpiece,energymeter

Singlecheckvalve

Surfacesensor

Ballvalveclosed

Thermostaticvalve,DHW

Filling/drainvalve

Diff.pressurecontrollerwithowlimiter

Strainer

Testconnection

DHW:DomesticHotWater

DCW:

DomesticColdWater

HWC:

HotWaterCirculation

DHSupply:DistrictHeatingSupply

DHReturn:DistrictHeatingReturn

HESupply:HeatingSupply

HEReturn:HeatingReturn

5.2.1Technicalparameters

Technicalparameters

Nominalpressure:PN10(PN16versionsareavailableonenquiry)

Max.DHsupplytemperature:

T–max=120°C

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

6.0Controls

6.1Heatingcircuit

6.1.1Differentialpressurecontroller

Thedifferentialpressurecontrollersmoothsouttheuctuationsin

pressurearrivingfromthedistrictheatingnetwork.Theoperating

pressureinthesubstationisthusheldsteady.

6.1.2HEtemperaturecontrol

TheHEowtemperatureintheheatingcircuitiscontrolledbythe

HEtemperaturecontroller.

6.1.3RAVKcontroller

RAVKcontroller(25-65°C).Thetemperaturesettingisasfollows:

1=25°C

2=35°C

3=45°C

4=55°C

5=65°C

Thevaluesareintendedasaguide.

Thermostaticcontrol

ThetemperatureoftheHEowlineisadjustedasfollows:

Toincreasetemperature,turnthehandleonthethermostatic

controllertoselectahighernumber.

Todecreasetemperature,turnthehandleonthethermostatic

controllertoselectalowernumber.

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

6.1.4AVTBcontroller(30–100°)

Thetemperaturesettingisasfollows:

1=35°C

2=55°C

3=75°C

4=95°C

5=100°C

Thevaluesareintendedasaguide.

Thermostaticcontrol

ThetemperatureoftheHEowlineisadjustedasfollows:

Toincreasetemperature,turnthehandleonthethermostatic

controllertoselectahighernumber.

Todecreasetemperature,turnthehandleonthethermostatic

controllertoselectalowernumber.

6.1.5Electroniccontrol

Substationswithelectroniccontrolmustbesetinaccordancewith

manufacturer´sinstructions.

Wheretheroomtemperatureiscontrolledbyradiatorthermostats,

itisrecommendedthatthermostatsbesetforminimum

temperatureineachroom.

6.1.6Outdoortemperaturesensor(ESMT)

Outdoorsensorsshouldbemountedsoastoavoidexposureto

directsunlight.Theyshouldnotbeplacedclosetodoors,windows

orventilationoutlets.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

6.1.7CirculatorpumpUPM3

UPM3Pumpscanbecontrolledinconstantpressure,proportional

pressureorconstantspeedmodedenedbythemeansofasmart

userinterface.

Thevariablespeedmodulatingmodesallowthepumptomatchits

performancetothesystemrequirements,helpingtoreducenoise

whenthermostaticvalvesareclosingdown.

EnergylabellingclassA

6.1.8GrundfosUPM3AUTOLinstructions

Controlmode

Youcanswitchfromtheperformanceviewtothesettingsviewbypressingthepushbutton.Thesettingsviewshowswhichmode

controlsthecirculator.After2seconds,thedisplayswitchesbacktoperformanceview.

Ifyoupressthebuttonfor2to10seconds,theuserinterfaceswitchesto"settingselection"iftheuserinterfaceisunlocked.Youcan

changethesettingsastheyappear.Theselectionofthecontrolmodedependsonthesystemtypeandtheallocationofpressurelosses.

Ifyoupressthekeylockformorethan10seconds,youcantogglebetweenenabling/disablingthekeylockfunction.

Function

Recommendedfor

Green

YellowYellowYellowYellow

Proportionalpressure1

1-pipesystems

µµ

Proportionalpressure2

µµµ

Proportionalpressure3

2-pipesystems

µµµµ

Constantpressure1

Underoorheating

µµ

Constantpressure2

µµµ

Constantpressure3

µµµµ

ConstantCurve1

µµµ

ConstantCurve2

µµµµ

ConstantCurve3

µµµµµ

ConstantCurveMax.

µµµµ

Operationstatus

Function

Recommendedfor

Green

YellowYellowYellowYellow

Standby**OnlyPWMcontrolled

0%≤P1≤25%

µµ

25%≤P1≤50%

µµµ

50%≤P1≤75%

µµµµ

75%≤P1≤100%

µµµµµ

Alarmstatus

Function

Recommendedfor

RedYellowYellowYellowYellow

Blocked

µµ

Supplyvoltagelow

µµ

Electricalerror

µµ

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

6.2DHWtemperaturecontrol

DHWtemperaturecontrol

TherearevarioustypesofDHWtemperaturecontrolusedin

Danfosssubstations.

DHWtemperatureshouldbeadjustedto45-50°C,asthisprovides

optimalutilisationofDHwater.AtDHWtemperaturesabove55°C,

thepossibilityoflimescaledepositsincreasessignicantly.

6.2.1RAVKcontroller

RAVKcontroller(25-65°C).Thetemperaturesettingisasfollows:

1=25°C

2=35°C

3=45°C

4=55°C

5=65°C

Thevaluesareintendedasaguide.

Thermostaticcontrol

DHWtemperatureisadjustedasfollows:

Toincreasetemperature,turnthehandleonthethermostatic

controllertoselectahighernumber.

Todecreasetemperature,turnthehandleonthethermostatic

controllertoselectalowernumber.

6.2.2AVTBcontroller(20–60°)

Thetemperaturesettingisasfollows:

1=20°C

2=35°C

3=50°C

4=60°C

5=70°C

Thevaluesareintendedasaguide.

TheAVTBoperatesatitsbestatDHsupplytemperaturesofupto

90°C.

Thermostaticcontrol

DHWtemperatureisadjustedasfollows:

Toincreasetemperature,turnthehandleonthethermostatic

controllertoselectahighernumber.

Todecreasetemperature,turnthehandleonthethermostatic

controllertoselectalowernumber.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

6.2.3Electric2–waymotorizedvalve

Actuatorswithorwithoutsafetyfunctionareavailablefor3-point

controls.Spring-returnactuatorscanbeusedtoprovidesafety

shut-offintheeventofpowerfailure.

6.3Other

6.3.1Safetyvalve

Thepurposeofthesafetyvalveistoprotectthesubstationfrom

excessivepressure.

Theblow-offpipefromthesafetyvalvemustnotbeclosed.The

blow-offpipeoutletshouldbeplacedsothatitdischargesfreely

anditispossibletoobserveanydrippingfromthesafetyvalve.

Itisrecommendedtochecktheoperationofsafetyvalvesat

intervalsof6months.Thisisdonebyturningthevalveheadin

directionindicated.

6.3.2Strainer

Strainersshouldbecleanedregularlybyauthorizedpersonnel.The

frequencyofcleaningwoulddependonoperatingconditionsand

themanufacturer’sinstructions.

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

6.3.3Fittingpiece

Thesubstationisequippedwithattingpieceforenergymeter.

Assemblyofenergymeters:

1:Closeballvalves

ClosetheballvalvesonDHSupplyandDHReturn,ifthereiswater

onthesystem.

2:Loosennuts

Loosenthenutsonthettingpiece.

3:Removettingpiece

Removethettingpieceandreplaceitwiththeenergymeter.Do

notforgetthegaskets.

4:Tightenconnections

Aftermountingoftheenergymeterremembertocheckand

tightenallthreadedconnections.

Sensorpocket,energymeter

Thesensorsoftheenergymeterismountedinthesensorpockets.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

6.4Maintenance

Thesubstationrequireslittlemonitoring,apartfromroutine

checks.Itisrecommendedtoreadtheenergymeteratregular

intervals,andtowritedownthemeterreadings.

RegularinspectionsofthesubstationaccordingtothisInstruction

arerecommended,whichshouldinclude:

Strainers

Cleaningofstrainers.

Meters

Checkingofalloperatingparameterssuchasmeterreadings.

Temperatures

Checkingofalltemperatures,suchasDHsupplytemperatureand

DHWtemperature.

Connections

Checkingallconnectionsforleakages.

Safetyvalves

Theoperationofthesafetyvalvesshouldbecheckedbyturning

thevalveheadintheindicateddirection.

Venting

Checkingthatthesystemisthoroughlyvented.

Inspectionsshouldbecarriedoutminimumeverytwoyears.

SparepartscanbeorderedfromDanfoss.Pleaseensurethatany

enquiryincludesthesubstationserialnumber.

Authorizedpersonnelonly

Assembly,start-upandmaintenanceworkmustbeperformedby

qualiedandauthorizedpersonnelonly.

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

7.0Troubleshooting

7.1Troubleshootingingeneral

Intheeventofoperatingdisturbances,thefollowingbasicfeatures

shouldbecheckedbeforecarryingoutactualtroubleshooting:

•thesubstationisconnectedtoelectricity,

•thestrainerontheDHsupplypipeisclean,

•thesupplytemperatureoftheDHisatthenormallevel

(summer,atleast60°C-winter,atleast70°C),

•thedifferentialpressureisequaltoorhigherthanthenormal

(local)differentialpressureintheDHnetwork–ifindoubt,ask

theDHplantsupervisor,

•pressureonthesystem-checktheHEpressuregauge.

Authorizedpersonnelonly

Assembly,start-upandmaintenanceworkmustbeperformedby

qualiedandauthorizedpersonnelonly.

7.2TroubleshootingDHW

ProblemPossiblecauseSolution

Strainerinsupplyorreturnlineclogged.Cleanstrainer(s).

DHWcirculationpumpoutoforderorwith

toolowsetting.

Checkcirculationpump.

Defectiveorcloggednon-returnvalve.

Replace–clean.

Noelectricity.Check.

Wrongsettingofautomaticcontrols,ifany.Toadjustanelectroniccontrollerfor

DHW,pls.noteenclosedinstructionsfor

electroniccontroller.

Scalingoftheplateheatexchanger.

Replace–rinseout.

Defectivemotorizedvalve.Check(usemanualfunction)–replace.

Defectivetemperaturesensors.

Check–replace.

ToolittleornoDHW.

Defectivecontroller.

Check–replace.

DCWisbeingmixedwiththeDHW,e.g.in

adefectivethermostaticmixingvalve.

Check–replace. Hotwaterinsometapsbutnotinall.

Defectiveorcloggednon-returnvalveon

circulationvalve.

Replace–clean.

Taptemperaturetoohigh;DHWtapload

toohigh.

Thermostaticvalveadjustedtoatoohigh

level.

Check–set.

Scalingoftheplateheatexchanger.

Replace–rinseout. Temperaturedropduringtapping.

LargerDHWowthanthesubstationhas

beendesignedfor.

ReduceDHWow.

Thermostaticcontrolvalvedoesnotclose

TemperaturedifferencebetweenDH

supplyandDHWsetpointtoolow.

Lowerthesetpointtemperatureor

increasetheDHsupplytemperature.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

7.3TroubleshootingHE

ProblemPossiblecauseSolution

Toolittleornoheat.StrainercloggedinDHorHEcircuit

(radiatorcircuit).

Cleangate/strainer(s).

ThelterintheenergymeteronDHcircuit

clogged.

Cleanthelter(afterconsultingtheDH

plantoperator).

Defectiveorwronglyadjusteddifferential

pressurecontroller.

Checktheoperationofthedifferential

pressurecontroller–cleanthevalveseatif

required.

Sensordefective–orpossiblydirtinthe

valvehousing.

Checktheoperationofthethermostat–

cleanthevalveseatifrequired.

Automaticcontrols,ifany,wronglysetor

defective-possiblypowerfailure.

Checkifthesettingofthecontroller

iscorrect–seeseparateinstructions.

Checkthepowersupply.Temporary

settingofmotorto“manual”control–see

instructionsonautomaticcontrols.

Pumpoutofoperation.Checkifthepumpisreceivingpowerand

thatitturns.Checkifthereisairtrappedin

thepumphousing–seepumpmanual.

Thepumpissetattoolowspeedof

rotation.

Setthepumpathigherspeedofrotation.

Pressuredrop–thepressuredropon

theradiatorcircuitshowslowerthan

recommendedoperatingpressure.

Fillwateronthesystemandcheckthe

functioningofthepressureexpansion

vesselifrequired.

Airpocketsinthesystem.Venttheinstallationthoroughly.

Limitingofthereturntemperature

adjustedtoolow.

Adjustaccordingtoinstructions.

Defectiveradiatorvalves.

Check–replace.

Unevenheatdistributioninbuilding

becauseofincorrectlysetbalancingvalves,

orbecausetherearenobalancingvalves.

Adjust/installbalancingvalves.

Diameterofpipetosubstationtoosmallor

branchpipetoolong.

Checkpipedimensions.

Unevenheatdistribution.Airpocketsinthesystem.Venttheinstallationthoroughly.

DHsupplytemperaturetoohigh.

Wrongsettingofthermostatorof

automaticcontrols,ifany.

Adjustautomaticcontrols,–see

instructionsforautomaticcontrols.

Defectivecontroller.Thecontrollerdoes

notreactasitshouldaccordingtothe

instructions.

Callautomaticcontrolsmanufactureror

replacetheregulator.

Defectivesensoronself-actingthermostat.

Replacethermostat–orsensoronly.

DHsupplytemperaturetoolow.

Wrongsettingofautomaticcontrols,ifany.

Adjustautomaticcontrols–seeinstructions

forautomaticcontrols.

Defectivecontroller.Thecontrollerdoes

notreactasitshouldaccordingtothe

instructions.

Callinautomaticcontrolsmanufactureror

replacecontroller.

Defectivesensoronself-actingthermostat.

Replacethermostat–orsensoronly.

Wrongplacement/ttingofoutdoor

temperaturesensor.

Adjustlocationofoutdoortemperature

sensor.

Strainerclogged.Cleangate/strainer.

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

OperatingGuideTermixBTDROMIX

ToohighDHreturntemperature.

Toosmallheatingsurface/toosmall

radiatorscomparedtothetotalheating

requirementofthebuilding.

Increasetotalheatingsurface.

Poorutilizationofexistingheatingsurface.

Defectivesensoronself-actingthermostat.

Makesuretheheatisdistributedevenly

acrossthefullheatingsurface–openall

radiatorsandkeeptheradiatorsinthe

systemfromheatingupatthebottom.It

isextremelyimportanttokeepthesupply

temperaturetotheradiatorsaslowas

possible,whilemaintainingareasonable

levelofcomfort.

Thesystemissinglepipeloop.

Thesystemshouldfeatureelectronic

controlsaswellasreturnsensors.

Pumppressuretoohigh.Adjustpumptoalowerlevel.

Airinsystem.

Ventthesystem.

Defectiveorincorrectlysetradiator

valve(s).Singlepipeloopsystemsrequire

specialone-piperadiatorvalves.

Check–set/replace.

Dirtinthemotorizedvalveorinthe

differentialpressurecontroller.

Check–cleanout.

Defectivemotorizedvalve,sensoror

automaticcontroller.

Check–replace.

Electroniccontrollernotadjustedcorrectly.Adjustaccordingtoinstructions.

Noiseinsystem.

Pumppressuretoohigh.Adjustpumptoalowerlevel.

Heatloadtoohigh.

Defectivemotorizedvalve,sensoror

electroniccontroller.

Check–replace.

7.4Disposal

Disposal

Thisproductshouldbedismantledanditscomponents

sorted,ifpossible,invariousgroupsbeforerecycling

ordisposal.

Alwaysfollowthelocaldisposalregulations.

DanfossDistrictEnergy

VI.HE.F2.02/LUK40661

DEN-GT

OperatingGuideTermixBTDROMIX

DEN-GT

VI.HE.F2.02/LUK40661

DanfossDistrictEnergy

Page is loading ...

Danfoss BTD RO MIX Operating instructions

Brand: Danfoss

Model: BTD RO MIX

Type: Operating instructions

Features of the Danfoss BTD RO MIX:

Pre-fabricated with a differential pressure controller, fitting piece and sensor pockets for insertion of heat meter as well as strainer and ball valves.
Mixing loop including pump, controls and non-return valve.
Heating circuit for direct generation of heat. The differential pressure control sets the optimal operation conditions for radiator thermostatic valves in order to enable individual temperature control in each room.

Download PDF

report

Danfoss BTD RO MIX Operating instructions

Danfoss BTD RO MIX Operating instructions

Related papers

Other documents