Feiss F3034/4PN Installation guide

Type
Installation guide

Feiss F3034/4PN is a 4 Light Pendant that can be dimmed with a standard incandescent dimmer. It is safety listed for dry locations only and must be installed by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°C supply conductors. The fixture may be hung from a sloped ceiling. For re-lamping, remove a small glass panel, reach into the fixture to replace the lamp (Max Wattage information is available on the label on the lamp socket), and reinstall the glass panel.

Feiss F3034/4PN is a 4 Light Pendant that can be dimmed with a standard incandescent dimmer. It is safety listed for dry locations only and must be installed by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°C supply conductors. The fixture may be hung from a sloped ceiling. For re-lamping, remove a small glass panel, reach into the fixture to replace the lamp (Max Wattage information is available on the label on the lamp socket), and reinstall the glass panel.

1
Installation Instructions for
Diamond 4 Light Pendant
1.1
F3034-4
Pendant
F3034/4
GP I :ENERAL RODUCT NFORMATION
These fixtures are intended to be installed utilizing NEC compliant
junction boxes.
This product is safety listed for dry locations only.
This product may be dimmed with a standard incandescent dimmer.
1
2
1A
3
CAUTION - RISK OF FIRE
This product must be installed in accordance with the
applicable installation code by a person familiar with the
construction and operation of the product and the hazards
involved.
Use minimum 90°c supply conductors.
4
5
6
FRAME
6
3
4
5
LAMP
LARGE GLASS PANEL
CHAIN
FIXTURE LOOP
2
11
Secure the mounting plate to the junction box.
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
Match the shape of the glass panels with the shapes on the frame, then install the glass by carefully placing them into the frame and
securing them using the tabs.
Feed the cord through the fixture loop and screw it onto the fixture.
Determine the wanted height of the fixture and remove a portion of the chain by opening a link and removing it from the bottom, then
install a quick link onto both ends of the chain.
Install a quick link to the fixture loop and another to the screw collar.
Weave the cord through the chain, cover, canopy, and out of the electrical box. Trim the cord leaving enough to make electrical
connections.
Connect the fixture to a suitable ground in accordance to local electrical codes.
Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut.
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire nut.
Neatly place all wires into the junction box, place the cover and canopy onto the threaded nipple, and secure them in place by screwing
the screw collar to the threaded nipple.
For re-lamping, remove a small glass panel as shown, reach into the fixture to replace lamp, and reinstall the glass panel.
SOCKET
7
8
9
10
11
12
SMALL GLASS PANEL
QUICK LINK
SCREW COLLAR
MOUNTING PLATE
CANOPY
JUNCTION BOX
3
TAB
6
COVER
THREADED NIPPLE
4
7400 Linder Ave, Skokie, IL 160077
800.969.3347
www.Feiss.com
© 2015 Feiss.All rights reserved.The "Feiss" graphic is a
registered trademark of Feiss. Feiss reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
SAVETHESE INSTRUCTIONS!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Feiss F3034/4PN Installation guide

Type
Installation guide

Feiss F3034/4PN is a 4 Light Pendant that can be dimmed with a standard incandescent dimmer. It is safety listed for dry locations only and must be installed by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°C supply conductors. The fixture may be hung from a sloped ceiling. For re-lamping, remove a small glass panel, reach into the fixture to replace the lamp (Max Wattage information is available on the label on the lamp socket), and reinstall the glass panel.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI