Weighing mode Menu
Press briefly Press and hold Key Press briefly Press and hold
• Switch on balance • Switch off balance • Quit menu without • Quit menu without
• Taring saving settings saving settings, switch
• With entries: cancel off balance
entry
• Zero setting (Re-zero) • Adjustment • No function • No function
or initiating test
• No function • Suppress or call up • No function • No function
last decimal place
• Confirm entry and • Confirm entry and • Confirm entry and • Confirm entry and
return to weight return to weight return to last weight return to last weight
display display display display
• Print out displayed • Enter menu • Confirm entry and • Save menu settings
value return to start of and return to
menu weighing mode
Key definition Operating instruction Section 1.4
Display Operating instruction Section 1.5
Menu Operating instruction Section 6
1/10d
Cal / Test
0
Menu
Short form operating instruction
PR/SR-balances
For detailled information see operating instructions
On
Off
C
T
APPL
Section 6.1
WEIGH
Section 6.2
CAL
Section 6.3
SYSTEM
Section 6.4
Dynamic
Count
Tot
+/-Stats
Formula
Vibr
Process
Repro
Unit 1
Unit 2
CustomUnit
AutoZero
PreTare
Test
Calibration
Settings
Printout
Beep
Date
Time
Bal ID
Icons
StartUp
PassWord
Simple weighing
MENU
Section 6
Internal
External
Weight Transfer
Header
Piece counting
Totalization
Formulation
Type of weighing
Repeatability
Surroundings
Dynamic weighing
Weight unit 1
Weight unit 2
Automatic zero
correction
Tare function
Internal
weight
External
weight
Present settings ...
Header printout
•Date
•Time
•Balance ID
•Lot ID
Sample ID
Config. printout
•Manual
•Auto
•AutoNoZeros
Acoustic signal
Date entry
Time entry
Balance identification
entry
Symbols off/on
Start Up procedure
Menu entry
Password protection
None
Configuration
Test of balance
precision
Password
(when set)
Reset
PrintList
Factory Setting
Configuration:
adjustment
Statistics
± Weighing
English
Deutsch
Français
Español
Italiano
Russian
Nihongo
LANGUAGE
Section 6.5
proFACT
CalInt
VariCal
History
Manual adjustment with
internal weight
Fully automatic and/or
time controlled
adjustment
(internal weight)
Adjustment with
external weight
History of the last
50 adjustments
Custom unit
Print list
*
stability detector; fades when the weight display is stable
signifies displays which do not correspond to the weight
currently loaded, e.g. difference to target weight
Repeatability
("ReproSet")
Type of weighing
("WghProcess")
Surroundings
("Vibrations")
Low
High
Fill
Check
Excellent
Best
OFF
Good
Medium
Universal
AutoCal
Cal
G
PT
T
Net
T Net
Automatic adjustment or test necessary
Display of gross weight
Display of preset tare weight
Display of tare weight
Display of net weight
Display of the net total weight
Dynamic weighing
Standard
Adapt OFF
1)
1)
1)
in Display flashes
External adjustment or test necessary
+/- Statistic Section 5.4
Section 6.1.5 configured : APPL +/-Weigh .....
Piece counting weighing Section 5.2
Section 6.1.3 configured : APPL Count
Dynamic weighing Section 5.1
Section 6.1.2 configured : APPL Dynamic .....
Menu
Totalizing Section 5.3
Section 6.1.4 configured : APPL Tot .....
© Mettler-Toledo GmbH 2001 11780240 Printed in Switzerland 0102/7.12
Mettler-Toledo GmbH, Laboratory & Weighing Technologies, CH-8606 Greifensee, Switzerland
Phone +41-1-944 22 11, Fax +41-1-944 30 60, Internet http://www.mt.com
Subject to technical changes
Extended basic functions Section 4
Settings:
System PrintOut Header .....
These functions can be configured additionaly to all other applications
• Section 4.1 Header (Date, Time, Bal ID)
• Section 4.2 LotID (Alphanumeric series identification)
• Section 4.3 SampleID (Sample identification)
• Section 4.4 PreTare (Entering a fixed tare weight)
Menu
Menu
Menu
Menu
Menu
Menu
Menu
Menu
Menu
Formulation weighing Section 5.5
Section 6.1.6 configured : APPL Formula
Menu
Menu
61.20 g
Manual start
(of dyn. weighing)
Item counter
Set item counter and previous results to zero
Result of the last dynamic weighing
Duration of the dynamic weighing selectable
WeighTime
1 2 3 5 10 20
Start n=6 dw=60.12g Results Clear WghTime
Set result output
0.0g
Fix10 Opt Set PCS
10 20 30 Var PcWgt Fix
Entry inquiry of piece weight
Entry of reference number
Setting of reference number, or entry inquiry of the piece weight
Calculation of piece weight
out of 10 pieces
Switching between pieces (pcs)
and weight (g)
optimization of counting accuracy
PW=1.65g
1 2 3 4 5 6 7 8 9 0
<
Definition of the fixed reference key
112.76 g
M+ n=1 Results Comp. Clear
Entry of target weight and identification
Selection of 1 of the 5 results
Weight transfer
(Current Component weight)
Entry of target weight
NextComp
Weight SampleID
Entry of identification number
Display of current component weight
Display of difference between target and actual component weight ( * )
Display of total net weight of all
components transferred so far
Display of total weight on the balance "gross" ( G )
Display of tare (container) weight ( T )
CmpWgt CmpDiff NetTot Gross TareWgt
Item counter
Item counter and
results set to zero
Item counter
61.20 g
M+ n=6 ∑=879.60g M- Clear
Edit function
Correction key
Transfer of weight value
Current total of weight values
Set item counter and results to zero
Max n= ...
1 2 3 4 5 6 7 8 9 0 <
112.20 g
M+ n=6 x=3 Diff SetRef Results Clear
0.00 g
Nom -Tol +Tol
Results
<T- >T+ mean Sdev Srel min max sum
minus tolerance
Selection and (Diff) of one of the 8 results
Nominal weight
Set item counter and results to zero
Number of tolerance violations
plus tolerance
Setting of Reference values Nom -Tol +Tol
Display: Difference to target weight
or absolute weight (Abs)
Max. value number and tolerance violations
Minimum weight value
Max. weight value
Transfer of weight value
Sum
Mean value
Standard deviation
Relative standard deviation
*P11780240*
/
