Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-(845-4641)
or visit the our web site at
vikingrange.com in the US or
brigade.ca in Canada
F21023A EN
(101513)
Installation Guide
Built-In Refrigeration Top Grille Installation
(Dual Installation)
3
Grille Kit Components
2
NOTE: These instructions include information on how to remove the current grilles and re-install
the grille kits. For information on dimensions, specifications and refrigerator installation, please
refer to the Installation Guides included with the refrigerators.
1. Grille Assembly (1)
2. "Z" shaped side trim (1)
3. "J" shaped center trim (1)
4. Side trim scr
ews (12)
5. Center trim scr
ews (8)
1
2
Place both units in front of cutout.
Pull the center grille louver up
at an angle and pull out.
3
4
Using an 8” magnetic nut driver, remove
the two 1/4” screws from each grille. Retain the screws
for installation of the new grille kit.
Remove grille assemblies.
Grille Removal
Side Trim Installation - Professional ModelsSide Trim Installation - Professional Models
• Remove cabinet side trim mounted on the left hand side of the refrigerator to be installed
on the right side of the installation. Replace with the “Z” shaped side trim provided in the
grille kit using the 12 screws included with the grille kit.
4
Cabinet Side Trim
“Z” Shape
Cabinet Cabinet
Right Hand Door Unit
Left Hand Door Unit
Anti-Tip
Lag Bolts
2x4 mounting board fastened to
wall at top of cabinet opening
• Engage the right hand refrigerator’
s left side trim into the “J” shaped portion of the left side
refrigerator’s right side trim.
• Finish unit installation according to installation instructions provided in each unit.
NOTE: Professional models ship with standard mount cabinet side trim attached to both sides.
For standard installations, leave the cabinet side trims attached to the right side of the
refrigerator to be installed on the right and the left side of the refrigerator to be installed on the
left.
OR
For flush installations, replace the cabinet side trims attached to the right side of the refrigerator
to be installed on the right and left side of the refrigerator to be installed on the left with the
flush mount side trim included in the boxes attached to the backs of the refrigerators.
NOTE: Cutouts are different for standard and flush installations. Please refer to Installation Guide
included with refrigerators for more complete dimension and specification information.
Left Hand
Cabinet "Z"
Side Trim
Centre Trim “J”
Shape
5
76
Side Trim Installation - Custom Panel ModelsSide Trim Installation - Custom Panel Models
• Remove cabinet side trim mounted on the left hand side of the refrigerator to be installed
on the right side of the installation. Replace with the “Z” shaped side trim provided in the
grille kit using the 12 screws included with the grille kit.
• Remove cabinet side trim mounted on the right side of the refrigerator to be installed on
the left side of the installation. Replace with the “J” shaped side trim provided in the grille
kit using the 8 screws included with the grille kit.
Cabinet Side Trim
“Z” Shape
Cabinet Cabinet
Right Hand Door Unit
Left Hand Door Unit
Anti-Tip
Lag Bolts
2x4 mounting board fastened to
wall at top of cabinet opening
• Engage the right hand refrigerator’
s left side trim into the “J” shaped portion of the left side
r
efrigerator’
s right side trim.
• Finish unit installation accor
ding to installation instructions provided in each unit.
Left Hand
Cabinet Side
Trim
Cabinet Side Trim
“J” Shape
98
Grille Assembly Install -
Professional Models
Grille Assembly Bracket Placement -
Professional Models
For 66” grille, excluding Custom Panel, Add/Remove brackets to full length grille as required.
See illustration below.
TOP
Use this bracket if 36” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on left side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 36” W. product is
on left side (facing unit), otherwise
remove.
*NOTE: Depending on unit configuration, two brackets should be removed and discarded. The
72” W. and 60” W. grille assemblies have all four (4) brackets mounted in the proper location.
66” Grille (back view)
• Remove center grille blade by lifting up and pulling forward.
• Insert grille into refrigerators. Screw grille assembly into units with (4) screws removed in
Step 3 (See Grille Removal Section).
1110
Grille Assembly -
Custom Panel Models
On Custom Panel models, grill spacers from original unit grilles must be reused:
• Remove grille brackets from grille included in the grille kit by removing 4 screws on each
grille bracket located on the back of the grille assembly.
• Remove grille brackets and spacers from original unit grilles by removing 4 screws on each
grille bracket located on the back of each grille assembly.
• Install grille brackets and spacers from original unit grilles onto grille from the kit using the
original grille hardware.
Important: The spacers must be oriented on the new grille the
same way they were on the original grille.
Also, remember to install the spacers on the
corresponding side of the installation (if installing a unit on the left side of an installation, its
grille spacers should be installed on the left side of the unified grille.)
Grille Assembly Bracket Placement -
Custom Panel Models
For 66” grille, excluding Custom Panel, Add/Remove brackets to full length grille as required.
See illustration below.
TOP
Use this bracket if 36” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on left side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 36” W. product is
on left side (facing unit), otherwise
remove.
*NOTE: Depending on unit configuration, two brackets should be removed and discarded. The
72” W. and 60” W. grille assemblies have all four (4) brackets mounted in the proper location.
66” Custom Grille (back view)
1312
Grille Assembly Install -
Custom Panel Models
• Remove center grille blade by lifting up and pulling forward.
• Insert grille into refrigerators. Screw grille assembly into units with (4) screws removed in
Step 3 (See Grille Removal Section).
1514
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Viking Range Center Trim Kit Operating instructions
-
GE ZWWP42D Installation guide
-
GE ZIS420NR User manual
-
GE ZISW48D Installation guide
-
Monogram Built-In All-Refrigerator/Freezer User manual
-
GE ZISW420D Installation guide
-
Amana Bottom freezer refrigerator User manual
-
-
-