Craftsman 580.752131 Owner's manual

Brand: Craftsman

Model: 580.752131

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752131

Operator'sManual

2550 PSi MAX

2.3 GPiViMAX

CLEAN SYSTEM

IViodelNo. 580.752131

PRESSUREWASHER

CUSTOMERHELPLINE

HOURS: Non. - Fri. 8 a.m. to 5 p.m. (CT)

i;i I!lwAemG

Before usingthis product, readthis

manualand follow all SafetyRules

and Operating Instructions.

] 1!1ADVERTEHCiA

Antes de utilizar el producto, lea este

manualy siga todas las Regiasde

Seguridade Instrucciones de Uso.

,, Safety

,,Assembly

,, Operation

,, Maintenance

,, Parts

• Espafiol,p. 30

This pressure washer is rated in accordance to the PressureWasher Manufacture Association

(PWMA) standard PWl01 (Testing and Rating Performance of Pressure Washers).

Esta limpiadora a presiOnest_ clasificada conforme a la norma PWl01 (comprobaci6n y clasificaci6n de rendimiento de limpiadoras

a presi6n) de la Asociaci6n defabricantes de bombas a presi6n (Pressure Washer Manufacture Association, PWMA).

Sears, Roebuckand Co., RoffrnanEstates,IL 60179 U.S.A.

Visit ourCraftsman website:www.craftsman.com

Part No. 207238GS Draft - (04/28/2008)

WARRANTY.......................................... 2

SAFETYRULES...................................... 2-5

FEATURESANDCONTROLS.............................. 6

ASSEMBLY........................................ 7-10

OPERATION....................................... 11-14

SPECIFICATIONS..................................... 15

MAINTENANCE.................................... 16-20

STORAGE........................................... 21

TROUBLESHOOTING.................................. 22

REPLACEMENTPARTS.............................. 23-27

EMISSIONCONTROLWARRANTY..................... 28-29

ESPANOL......................................... 30-55

HOWTO ORDERPARTS........................ BACKPAGE

ONE-YEARFULLWARRAHTYONCRAFTSMAHPRESSUREWASHER

If this pressurewasher fails dueto a defectin material or workmanship within one year from the dateof purchase,return it to

any Searsstore, other Craftsman outlet, or SearsParts & RepairCenterin the UnitedStates or Canadafor free repair (or

replacementif repair proves impossible).

All warranty coverageapplies for only 90 days from dateof purchaseif this pressure washer is ever usedfor commercial or

rentalpurposes.

This warranty gives you specific legal rights, and you mayalso haveother rights which vary from stateto state.

Sears, Roebuck and Co., Hoffman Estates, IL 60178

Sears Canada Inc., Toronto, Ontario, Canada M5B 288

,_ Thisisthe safetyalert symbol.It isusedto alert youtopotentialpersonalinjuryhazards.Obeyall safetymessages

thatfollow thissymboltoavoid possibleinjuryor death.

_Read this manualcarefully and becomefamiliar

with yourpressurewasher. Knowits applications,

its limitations, and any hazardsinvolved.

Thesafety alert symbol (,i_) is usedwith a signal word

(DANGER,CAUTION,WARNING),a pictorial and/or a safety

messageto alert you to hazards.BANGERindicatesa hazard

which, if not avoided, willresult in deathor serious injury.

WARNINGindicates a hazardwhich, if not avoided, could

result in deathor serious injury. CAUTIONindicatesa hazard

which, if not avoided, might result in minor or moderate

injury. NOTlCEindicatesa situation that could result in

equipment damage. Follow safety messagesto avoid or

reducethe risk of injury or death.

Hazard Symbolsand Meaninos

ToxicFumes Kickback

2 5-

SlipperySurface Fall

Fire

Explosion

ElectricalShock

FluidInjection

Operator'sManual

MovingParts FlyingObjects

HotSurface

WARHJNG

Theengineexhaustfromthisproductcontains

chemicalsknowntotheState of California tocause

cancer,birthdefects,or otherreproductiveharm.

WARNING

Certaincomponentsin this productand related

accessories containchemicalsknownto the State of

California tocausecancer,birth defectsor other

reproductiveharm. Wash handsafter handling.

WARNING

Runningengine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathingcarbon monoxide can cause headache,

_ atigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting, or poisoning.

* OperatepressurewasherONLYoutdoors.

* Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

* DONOTstartor runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

* Usea respiratoror maskwheneverthereisa chancethat

vaporsmaybeinhaled.

* Readall instructionswith masksoyouarecertainthemaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

WARHIHG

_¢ isk of electrocution.

Contactwith power source can causeelectric

shock or burn.

* NEVERspraynearpowersource.

WARHIHG

Fueland its vapors are extremely flammable and

explosive.

Fireor explosion cancause severe burns or

death.

WHENADDINGORDRAININGFUEL

* TurnpressurewasherOFFandletit coolatleast2 minutes

beforeremovingfuelcap.Loosencapslowlyto relievepressure

in tank.

* Fillor drainfueltankoutdoors.

* DONOToverfilltank.Allowspaceforfuelexpansion.

* Iffuelspills,waituntilit evaporatesbeforestartingengine.

* Keepfuelawayfromsparks,openflames,pilotlights,heat,and

otherignitionsources.

* DONOTlighta cigaretteorsmoke.

WHENSTARTIN6EQUIPMENT

* Ensuresparkplug,muffler,fuelcap,andair cleanerarein

place.

* DONOTcrankenginewith sparkplugremoved.

WHENOPERATINGEQUIPMENT

* DONOTtip engineor equipmentat anglewhichcausesfuelto

spill.

* DONOTsprayflammableliquids.

WHENTRANSPORTINGORREPAIRINGEQUIPMENT

* Transport/repairwithfueltank EMPTYor withfuelshutoffvalve

OFF.

* Disconnectsparkplugwire.

WHENSTORINGFUELOBEQUIPMENTWITH FUELIN TANK

* Storeawayfromfurnaces,stoves,waterheaters,clothes

dryers,or otherappliancesthathavepilotlightor otherignition

sourcebecausetheycanignitefuelvapors.

WARHJHG

Startercord kickback(rapid retraction) can result

in bodily injury. Kickbackwill pull handand arm

_,_.< toward engine faster than you can let go.

Brokenbones, fractures, bruises, or sprains

could result.

• NEVERpull starter cord without first relieving spray gun

pressure.

. When starting engine, pull cord slowly until resistanceis felt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both handswhen using high

pressure spray to avoid injury when spray gun kicks back.

WARHIHG

Useof pressure washer cancreate puddles and

slippery surfaces.

Kickbackfrom spray gun cancause you to fall.

. Operatepressure washer from astable surface.

• The cleaningarea should haveadequateslopes and drainageto

reducethe possibility of a fall due to slippery surfaces.

. Be extremelycareful if you must usethe pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARHIHG

_ Contact with muffler result in serious

area can

burns.

_ Exhaustheat/gases can ignite combustibles,structures or damagefuel tank causing a fire.

• DO NOTtouch hot parts and AVOID hot exhaust gases.

. Allow equipment to cool before touching.

• Keepat least 5feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• Codeof FederalRegulation (CFR)Title 36 Parks, Forests,and

Public Property require equipment powered by an internal

combustion engine to havea spark arrester, maintained in

effective working order, complying to USDAForestservice

standard 5100-1C or later revision. Inthe State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other statesmay havesimilar laws.

WARHIHG

The high pressure stream of water that this

equipment produces can cut through skin and its

_ nderlying tissues, leading to serious injury and

)ossible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DONOTallow CHILDRENto operate pressure washer.

. NEVERrepair high pressure hose. Replaceit.

• NEVERrepair leaking connections with sealantof any kind.

Replaceo-ring or seal.

• NEVERconnect high pressure hoseto nozzle extension.

. Keephigh pressure hose connectedto pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, pressred button

and squeezespray gun trigger to releasehigh pressure, every

time you stop engine.

• NEVERaim spray gun at people, animals, or plants.

. DONOTsecure spray gun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

. NEVERusea spray gun which does not have atrigger lock or

trigger guard in place andin working order.

. Always be certain spray gun, spray tips and accessories are

correctly attached.

WARHIHG

_ Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOUR

PRESSUREWASHER

. Disconnectthe sparkplug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

. Use approved sparkplug tester.

• DONOTcheck for sparkwith spark plug removed.

WARHJHG

Starter and other rotating parts canentangle

hands, hair, clothing, or accessories.

* NEVERoperate pressure washer without protective housing or

covers.

* DO NOTwear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

* Tie up long hair and remove jewelry.

WARNING

Risk of eye injury.

" _ JSpraycan splash back or propel objects.

Alwayswear safetygoggles when using this equipment or in

vicinity of where equipment is in use.

Beforestarting the pressure washer, be sureyou are wearing

adequatesafety goggles.

NEVERsubstitute safety glasses for safety goggles.

NOTICE

High pressure spray may damage fragile items including

lass.

DO NOTpoint spray gun at glasswhen using red (0°) spraytip.

NEVERaim spray gun at plants.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

Ifyou have questions about intended use, ask dealer or contact

Sears.

NEVERoperate units with broken or missing parts, or without

protective housing or covers.

DONOT by-pass any safetydevice on this machine.

DONOTtamper with governed speed.

DONOToperate pressurewasher above rated pressure.

DONOT modify pressure washer in any way.

Before starting pressure washer in cold weather, check all parts

of the equipment to besure ice has not formed there.

NEVERmove machine by pulling on hoses. Use handle

provided on unit.

Checkfuel system for leaksor signs of deterioration, such as

chafed or spongy hose,loose or missing clamps, or damaged

tank or cap. Correct all defects beforeoperating pressure

washer.

This equipment is designedto be usedwith Searsauthorized

parts ONLY.If equipment is usedwith parts that DO NOT

comply with minimum specifications, userassumes all risks

and liabilities.

KNOWYOURPRESSUREWASHER

_Read the Operator'sManual andsafety rulesbefore operatingyourpressurewasher.

Comparethe illustrations with your pressurewasher to familiarizeyourself with the locations of various controls and

adjustments. Savethis manualfor future reference.

---4b

A- Spray Gun-- Controlsthe application of water onto

cleaningsurfacewith trigger device,includes trigger lock.

B - Cleaning Tank - Usedto provide pressure washer safe

detergents into the low pressure stream.

C- Spray Tips -- Detergent,0°, 15° and 40°: for various

high pressure cleaning applications.

D - Recoil Starter -- Used for starting the engine manually.

E - FuelTank -- Filltank with regular unleadedfuel. Always

leaveroom for fuel expansion.

F - Throttle Lever -- Setsengine in starting mode for recoil

starter and stops a running engine.

G - AirFilter -- Protects engine by filtering dust and debris

out of intake air.

H - Pump -- Developshigh pressure.

J - AutomaticCool DownSystem -- Cycleswater through

pump when water reaches125°-155°F. Warm water will

dischargefrom pump onto ground. This system prevents

internal pump damage.

K- High Pressure Outlet -- Connectionfor high pressure

hose.

L - Water Inlet -- Connectionfor garden hose.

IVl- Oil Fill/Dipstick -- Check,add and drain engine oil here.

N - High Pressure Hose-- Connectone end to water pump

and the other end to spray gun.

Items Net Shown:

Idenification Label(near rear ofbase plate) -- Provides

modeland serial number of pressure washer. Pleasehave

these readilyavailableif calling for assistance.

NozzleExtensionwith QuickConnect-- Allows you to

switch betweenfour different spray tips.

Safety Goggles-- Always usethe enclosedsafety goggles

when running your pressure washer.

Warning/Operating instructionsTag-- identifies hazards

and proper procedureto start/stop pressure washer.

Yourcleaningsystemrequiressomeassemblyandisready

foruseonlyafterithasbeenproperlyservicedwiththe

recommendedoilandfuel.

If you haveany problemswith the assemblyof your

pressurewasher, please call the pressurewasher heipline

at 1-800-222-3135.

UNPACKTHEPRESSUREWASHER

8. Attach nozzleextension to spray gun.

9. Select/attachquick connect spray tip to nozzleextension.

Attach Handle and Cleaning Tank

1. Placehandle (A) onto handlesupports (B) connectedto

main unit. Make sure holes (C) in handlealign with holes

1. Removeeverything from carton exceptpressure washer.

2. Opencarton completely bycutting eachcorner from top

to bottom.

3. Removepressure washer from carton.

CARTONCONTENTS

Checkall contents, if any parts are missing or damaged,call

the pressure washer helpline at 1-800-222-3136.

* Main Unit

* Handle

* CleaningTankAssembly

* High PressureHose

* Spray Gun

* NozzleExtensionwith Quick ConnectFitting

* Oil Bottle

* DetergentSiphoning Hose/Filter

* Gun Holder Wireform

* Parts Bag (which includes the following):

* Operator's Manual

* Owner's Registration Card

* SafetyGoggles

* Bagcontaining 4 multi-colored Spray Tips

* HandleFasteningHardwareKit (whichincludes):

* CarriageBolts (2)

* "L" Bolt

* Plastic Knobs (4)

, TreeClips (4)

Becomefamiliar with eachpiecebefore assemblingthe

pressure washer, identify all contents with the illustration on

page 6. If any parts are missing or damaged,callthe

pressure washer helpline at 1-800-222-3136.

ASSEMBLINGCLEANINGSYSTEM

Your Craftsmancleaningsystem will needassembly before

operation:

1. Fill out and send in registration card.

2. Attach handleand cleaningtank.

3. Connectdetergent siphon hoseto pump.

4. Add oil to engine crankcase.

5. Add fuel to fuel tank.

6. Connectpressure hoseto spray gun and pump.

7. Connectwater supply to pump.

NOTE:It may be necessaryto move the handle supports

from sideto side in order to align the handle so it will slide

overthe handlesupports.

2. Insert carriagebolts (B) through holes from back of unit

and attacha plastic knob (E)from front of unit. Tighten

by hand.

Placecleaningtank (F) over holes (6) on handle

(viewing from front of unit). Pushthe tree clips (H) into

the holes until they sit flat againstthe cleaningtank.

"-.

Insert "L" bolt (J) through hole just above cleaningtank

on right side of handle (viewing from front of unit). Hold

bolt in placeand attachplastic knob (K) from inside of

unit. Tighten by hand.

Insert spray gun holder wireform (h) through holejust

abovecleaningtank on left side of handle (viewing from

front of unit). Hold wireform in placeand attach a plastic

knob (B) from inside of unit. Tighten by hand.

Attach Detergent Siphon Hose to Pump

Thepressure washer is equipped with two detergent

siphoning hoses.One is attachedto the cleaningtank and

one is loosefor siphoning pressure washer safe detergents

from a bottle or container.

Attach one of the detergent siphon hoses (O)to the barbed

hose fitting (D) on the pump.

IMPORTANT:Onlyone detergent siphoning hosecan be used

at a time. When cleaningtank is not used, makesure

detergent shut-off valve on cleaningtank is in the "Off"

position.

Add Enoine OiJ

1. Placepressure washer on a flat, levelsurface.

2. Cleanarea around oil fill and remove yellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE

Improper treatment of pressurewasher can damageit and

shorten its life.

DONOTattempttocrankor starttheenginebeforeit hasbeen

properlyservicedwith therecommendedoil.Thismayresultin

anenginefailure.

4. Replaceoil fill cap/dipstick and fully tighten.

Add Fuel

Fuelmust meet theserequirements:

* Clean,fresh, unleadedgasoline.

* A minimum of 87 octane/87AKI (91 RON).High altitude

use, seeHigh Altitude.

* Gasolinewith up to 10% ethanol (gasohol) or up to 15%

MTBE(methyl tertiary butyl ether) is acceptable.

NOTICE

Avoid pressure washer damage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

DONOTuseunapprovedgasolinesuchasE85.

DONOTmixoil in gasoline.

DONOTmodifyengineto runon alternatefuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage.All fuel is notthe

same. If you experiencestarting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline. The

emission control system for this engine is EM (Engine

Modifications).

WARHIHG

_ uel and itsvapors are extremely flammable and

explosive.

Fireor explosion can causesevere burns or

death.

WHENADDINGFUEL

* TurnpressurewasherOFFandletitcoolatleast2 minutes

beforeremovingfuelcap.Loosencapslowlyto relievepressure

in tank.

* Fillfueltankoutdoors.

* DONOToverfilltank.Allowspaceforfuelexpansion.

* Iffuelspills,waituntilit evaporatesbeforestartingengine.

. Keepfuelawayfromsparks,openflames,pilotlights,heat,and

otherignitionsources.

* DONOTlighta cigaretteorsmoke.

1. Cleanareaaround fuel fill cap, removecap.

2. Slowly add regular unleadedfuel (E) to fuel tank (F). Be

careful not to overfill. Allow about 1.5" (4 cm) (6) of

tank spacefor fuel expansion.

3. Installfuelcap and wait for anyspilled fuelto evaporate.

CAUTION!Alcohol-blended fuels (calledgasohoI,ethanol or

methanol) can attract moisture, which leadsto separation and

formation of acids during storage.Acidic gascan damagethe

fuel system of an enginewhile in storage.

Toavoid engine problems, the fuel system should betreated

with a fuel preserver or emptied before storage of 30 days or

longer. If adding a fuel preserver,fill the fuel tank with fresh

fuel. if only partially filled, air in the tank will promote fuel

deterioration during storage, if fuel preserver is not used,

drain the fuel tank, start the engine and let it run until the fuel

lines and carburetor are empty. Usefresh fuel next season.

See Storagefor additional information.

NEVERuseengine or carburetor cleanerproducts in the fuel

tank as permanent damagemay occur.

HighAltitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane/ 85 AKI (89 RON)gasoline is acceptable.To

remain emissions compliant, high altitude adjustment is

required. Operationwithout this adjustment will cause

decreasedperformance, increasedfuel consumption, and

increasedemissions. Seea qualified Searsdealer for high

altitude adjustment information. Operationof the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

Connect Hose and Water Supply to Pump

[ NOTICE

JDONOT the without the connected

run

pump

water

supply

and turned on.

L amageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

NOTE:Removeand discardthe shipping caps from the

pump's high pressure outlet and water inlet beforeattaching

hoses.

1. Uncoil high pressure hose and attach one end of hoseto

baseof spray gun. Tighten by hand.

WARNING

Thehigh pressurestream of water that this

_ quipment produces cancut through skin and its

underlyingtissues, leadingto serious injury and

)ossible amputation.

. NEVERconnecthighpressurehoseto nozzleextension.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

Attach other end of high pressure hoseto high pressure

outlet on pump. Tighten by hand.

Beforeconnectinggarden hoseto water inlet, inspect

inlet screen (A). Cleanscreen if it contains debris or have

it replacedif damaged•DONOTrun pressurewasher if

inlet screenis damagedor missing.

4. Run water through garden hose for 30 secondsto flush

it of debris• Turn off water•

IMPORTANT:DONOTsiphon standing water for the water

supply• UseONLYcold water (less than IO0°F).

5. Connectgarden hose (not to exceed50 feet in length) to

water inlet•Tighten by hand•

NOTICE

Using a OneWay Valve(vacuum breakeror check valve)at

pump inlet cancause pump or inlet connector damage•

ThereMUSTbeatleasttenfeetofunrestrictedgardenhose

betweenthe pressurewasherinletandanydevice,suchasa

vacuumbreakerorcheckvalve•

Damageto equipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty•

WARHIHG

Riskof eyeinjury•

• _ ISpray cansplash back or propel objects•

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityof whereequipmentisin use.

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles•

NEVERsubstitutesafetyglassesfor safetygoggles•

6. Turn ONthe water, press red button (B) on the gun and

squeezethe trigger to purge the pump system of air and

impurities•

CheckJist Before Starting Engine

Reviewthe unit to ensureyou have performed all of the

following:

1. Besure to read Safety Rulesand Operationsections

before usingthe cleaning system•

2. Makesure handle is in placeand secure•

3. Checkthat oil has beenadded to proper levelin engine

crankcase•

4. Add proper fuelto fuel tank•

5. Checkfor proper hoseconnections (high pressure and

water supply) and that there are no kinks, cuts, or

damageto the high pressure hose•

6. Provideproper water supply (not to exceedIO0°F).

HOWTO USEYOURCLEANJHGSYSTEM

If you haveany problems operatingyour pressure washer,

pleasecallthe pressure washer helpline at 1-800-222-3136.

Pressure Washer Location

PressureWasherClearance

,_ WARNING

_ Exhaustheat/gases can ignitecombustibles,

structures or damagefuel tank causing a fire.

* Keepatleast5ft. (152cm)clearanceonallsidesofpressure

washerincludingoverhead.

Placepressure washer outdoors in an areathat will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulateand enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is kept awayfrom any windows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in a confined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

,_ WARHJHG

Runningengine gives off carbon monoxide, an

_ dorless, colorless, poison gas.

Breathingcarbon monoxide can causeheadache,

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

. OperatepressurewasherONLYoutdoors.

* Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

. DONOTstartor runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

To Start Your Cleanin8 System

To start your engine-poweredcleaning system for the first

time, follow these instructions step-by-step. This information

also applies wheneveryou start the engine after you havelet

the pressure washer sit idle for at least a day.

1. Placepressure washer outside near an water source

capableof supplying water at a flow rategreater than

3.2 gallons per minute and no less than 20 PSIat

pressurewasher end of garden hose.

2. Checkthat high pressure hose istightly connectedto

spray gun and pump. SeeAssembyfor illustrations.

3. Makesure unit is in a levelposition.

4. Connectgarden hoseto water inlet on pressure washer

pump.

i NOTICE

DONOTrun the pump without the water supply connected

and turned on.

L amageto equipmentresultingfrom failureto followthisinstructionwillvoidwarranty.

5. Turn ONthe water,press red button on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

6. Placecolored quick connect spray tips in slots on holder

that's attachedto nozzleextension.

7. Attach nozzleextension to spray gun. Tighten by hand.

B. Choose spray tipyou wantto use and insert it into

nozzleextension. SeeHow to UseSpray Tips.

Move throttle lever to "Fast" position (A), shown as a

rabbit.

IMPORTANT:Beforestarting the pressure washer, be sure

¢ouare wearing adequatesafety goggles.

WARHIHG

Risk of eye injury.

_Spray can splash back or propel objects.

Alwayswear safetygoggles when using this equipment or in

vicinity of where equipment is in use.

Beforestarting the pressure washer, be sureyou are wearing

adequatesafety goggles.

NEVERsubstitute safety glasses for safety goggles.

NOTE:This unit is equipped with a ReadyStart@engine. A

ReadyStart@engine meansthere is no priming or choking

required.

10. Whenstarting engine, position yourself as

recommendedand grasp starter grip handle and pull

slowly until you feelsome resistance.Thenpull rapidly

to start engine.

WAIHIHG

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

_ toward engine faster than you can let go.

Brokenbones, fractures, bruises, or sprains

could result.

* NEVERpull starter cord without first relieving spray gun

pressure.

* When starting engine, pull cord slowly until resistanceis felt

andthen pull rapidly to avoid kickback.

* After each starting attempt, where enginefails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to releasehigh pressure.

* Firmly grasp spray gun with both handswhen using high

pressure spray to avoid injury when spray gun kicks back.

11. Return recoil starter slowly. DO NOT let rope "snap

back" against starter.

NOTE: Always keep the throttle lever in the "Fast" position

when operating the pressure washer.

WARHIHG

Thehigh pressurestream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leadingto serious injury and

)ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

* DONOTallowCHILDRENtooperatepressurewasher.

* Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

* NEVERaimspraygunatpeople,animals,or plants.

* DONOTsecurespraygun inopenposition.

* DONOTleavespraygununattendedwhilemachineis running.

* NEVERusea spraygunwhichdoesnothaveatriggerlockor

triggerguardin placeandin workingorder.

* Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

WARHIHG

_ Contact with muffler result in serious

area can

burns.

,_ Exhaustheat/gases can ignite combustibles,structures or damagefuel tank causing a fire.

* DONOTtouchhotpartsandAVOIDhotexhaustgases.

* Allowequipmenttocoolbeforetouching.

* Keepatleast5 feet(152cm) ofclearanceonall sidesof

pressurewasherincludingoverhead.

* Codeof FederalRegulation(CFR)Title36Parks,Forests,and

PublicPropertyrequireequipmentpoweredbyaninternal

combustionengineto haveasparkarrester,maintainedin

effectiveworkingorder,complyingto USDAForestservice

standard51BB-1Cor laterrevision.IntheStateof Californiaa

sparkarresterisrequiredundersection4442oftheCalifornia

Publicresourcescode.Otherstatesmayhavesimilarlaws.

Howto StopYourCleaningSystem

1. Releasespray gun trigger and letengine idlefor two

minutes.

2. Movethrottle to SLOWposition,then STOPposition (A).

3. ALWAYSpoint spray gun in a safe direction, push red

button and squeezespray gun trigger to releaseretained

high water pressure.

IMPORTANT:Spraygun traps high water pressure,even

when engine is stopped and water is disconnected.

WARHIHG

The high pressure stream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leadingto serious injury and

)ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

. Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntrigger,to releasehighpressure,every

time youstopengine.

How to Use Spray Tips

Thequick-connect on the nozzleextensionallows you to

switch between four different quick connect spray tips. Spray

tips can be changedwhile pressure washer is running once

spray gun trigger lock is engaged.Thespray tips vary the

spray pattern asshown.

FolJowthese instructions to changespraytips:

1. Pull back collar on quick-connect and puil current spray

tip off. Storespray tips in holder provided on the nozzle

extension.

WARHIHG

The high pressure stream of water that this

_ quipment produces can cut through skin and its

underlyingtissues, leadingto serious injury and

possible amputation.

• NEVERexchangespraytips withoutthetriggerlockedonthe

spraygun.

• DONOTtwist spraytips whilespraying.

Select desiredspray tip:

Low Pressure

Black

Useto apply

chemical

High Pressure

40° White 15° Yellow

1750 PSI 2200 PSI

2.3 GPM 2.2 GPM

0° Red

255OPSI

2.0 GPM

• For delicate rinse (lower pressure and higher flow),

for gentlecleaning of cars/trucks, boats, RV's, patio

furniture, lawn equipment, etc., select white 40°

spray tip.

• Forgeneral rinsing (medium pressure and medium

flow), ideal for most all purpose cleaning such as

home siding, brick patios, wood decks, driveways

and sidewalks,garage floors, etc., selectyellow

15° spray tip.

• For maximum rinsing (higher pressure and lower

flow), for stubborn or hard to reachsurfacesuch as

second story surfaces,paint removal,oil stains, rust

removal or other stubborn substances (tar, gum,

grease,wax, etc.), select red 0° spray tip.

• Toapply detergent,appliesproject specific cleaners

to help breakdown stubborn dirt and grime on a

variety of surfaces, selectblack detergentspray tip.

Pull backon collar,insert newspraytip and releasecollar.

Tugon spraytip to makesureit is securelyin place.

UsageTips

• For most effective cleaning, keepspray tip from 8to

24 inches (20 to 61 cm) awayfrom cleaningsurface.

• If you get spray tip too close, especially usinga high

pressure spray tip, you may damagesurface being

cleaned.

• DONOTget closer than 6 inches (15 cm) when cleaning

tires.

Cleaning and Applying Detergent

CAUTIOH

Chemicalscan causebodily injury, and/or property

damage.

NEVERusecausticliquidwith pressurewasher.

UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

To applydetergent follow these steps:

1. Attach desireddetergent siphon hosefollowing

instructions Attach DetergentSiphon Nose to Pump.

IMPORTANT:Be sureengine is off and allowed to cool before

switching detergentsiphoning hoses.

WARHIHG

s_ Contact with muffler result in serious

area can

burns.

_ Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing a fire.

• DONOTtouchhotpartsandAVOIDhotexhaustgases.

• Allowequipmentto coolbeforetouching.

2. Reviewuse of spray tips.

3. Preparedetergent solution as required by job.

4. Make sure detergent shut-off valve on cleaningtank is in

"Off" position.

5. If using cleaningtank, pour detergent into cleaningtank.

NOTE:Thecleaningtank holds one gallon.

6. Make sure black detergent spray tip is installed.

NOTE:Detergentcannot be applied with the high pressure

nozzles(White, Yellow or Red).

7. Make sure garden hoseis connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE

You must attachall hoses beforeyou start the engine.

Startingtheenginewithoutallthehosesconnectedandwithout

thewaterturnedONwill damagethepump.

Damageto equipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

8. Start engine following instructions How to Start Your

Pressure Washer.

9A. If using cleaningtank, rotate detergentshut-off valve on

cleaningtank to "On" position (A).

IMPORTANT:if using detergent siphoning hose, make sure

detergentshut-off valve on cleaningtank is in the "Off"

position.

9B. If using detergent siphoning hose, placesmall filter end

of detergent siphoning tube into detergent container.

NOTE:Makesure the filter is fully submerged in detergent

while applying detergent.

#OT/CE

Contact with the hot muffler can damagedetergent

siphoning tube.

Wheninsertingthefilterintoa detergentsolutionbottle,route

thetubesoasto keepit from inadvertentlycontactingthehot

muffler.

10. Apply detergentto a dry surface, starting at lower

portion of areato be washed and work upward, using

long, even, overlappingstrokes.

11. Allow detergentto "soakin"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surface from drying. DONOTallow detergent to dry on

(preventsstreaking).

Pressure Washer Binsing

ForRinsing:

1. If using cleaningtank, rotate detergent shut-off valve on

cleaning tank to "Off" position.

2. Removeblackspray tip from nozzleextension.

3. Selectand install desiredhigh pressure spray tip

following instructions How to Use Spray Tips.

4. Keepspray gun a safe distancefrom areayou plan to

spray.

spray gun cancauseyou

Kickbackfrom to fall.

. Operatepressurewasherfrom astablesurface.

• Beextremelycarefulifyou mustusethepressurewasherfrom

a ladder,scaffolding,or anyothersimilarlocation.

• Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

Apply a high pressure spray to a small areaand then

check surface for damage.If no damageis found, you

can assume it is okayto continue rinsing.

Start at top of areato be rinsed, working down with

same overlapping strokes asyou usedfor cleaning.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125°F.Thesystem engagesto cool the pump by discharging

the warmwater ontothe ground.

EHGINETECHNICALINFORMATIOH PRODUCTSPECIFICATiOHS

This is a single cylinder, L-head,air cooled engine. It is a low

emissions engine.

Inthe Stateof California, Model 120000 enginesare certified

by the California Air Resources Boardto meet emissions

standardsfor 125 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respectto the performance or

operational life of this engine.Theengine is warranted solely

according to the product and emissions warranties stated

elsewherein this manual.

Power Ratings

Thegross power rating for individual gas engine models is

labeledin accordancewith SAE(Societyof Automotive

Engineers)codeJ1940 (Small Engine Power & Torque

Rating Procedure),and rating performance hasbeen

obtained andcorrected in accordancewith SAEJ1995

(Revision2002-05). Torquevalues are derived at3060 RPM;

horsepower values are derivedat 3600 RPM.Actual gross

engine power will be lower and is affected by, among other

things, ambient operating conditions and engine-to-engine

variability. Givenboth the wide array of products on which

enginesare placedand the variety of environmental issues

applicableto operatingthe equipment, the gas engine will not

developthe ratedgross power when used in a given pieceof

power equipment (actual "on-site"or net power). This

difference is due to a variety of factors including, but not

limited to, accessories (air cleaner, exhaust,charging,

cooling, carburetor, fuel pump, etc.), application limitations,

ambient operating conditions (temperature,humidity,

altitude), and engine-to-engine variability. Dueto

manufacturing and capacity limitations, Briggs & Stratton

maysubstitute an engine of higher ratedpower for this

Seriesengine.

This pressurewasher is rated in accordanceto the Pressure

Washer Manufacture Association (PWMA) standard PW101

(Testingand Rating Performanceof PressureWashers).

Pressure Washer Specifications

Max Outlet Pressure ....................... 2,550 PSi

Max Flow Rate............................. 2.3 GPM

DetergentMix ........................ Use asdirected

Water SupplyTemperature .......... Not to exceed IO0°F

Engine Specifications

Bore ................................. 2.69 in. (68mm)

Stroke ............................... 2.04 in. (52mm)

Displacement ........................ 11.57in. (190 cc)

SparkPlug

Type: ............. Briggs & Stratton 802592 or 5095D

SetGapTo: ...................... O.030inch(0.76mm)

ArmatureAir Gap: ........... 0.006-0.010in.(O.15-O.25mm)

Valveclearancewithvalvespringsinstalledand piston1/4in.

(6 ram)pasttopdeadcenter(checkwhenengineiscold).

Intake.................... 0.005-0.007in.(0.13-0.18mm)

Exhaust .................. 0.007-0.009in.(0.18-0.23mm)

FuelCapacity............................... 1.6Quarts

OilCapacity........................ 18Ounces(0.5 liter)

NOTE:Forpractical operation, the engine load should not

exceed 85% of rated power. Enginepower will decrease

3-1/2% for each1,000 feet (300 meters) abovesea leveland

1% for each 10° F(5.6° C) above77° F(25° C). It should

operatesatisfactorily at an angle up to 15°.

OWHER'SRESPOHSIBILITIES Pump Oil

Maintenance Schedule

Followthe hourly or calendarintervals, whichever occurs

first. More frequent service is required when operating in

adverseconditions noted below.

* Changeengine oil

* Check/clean water inlet screen1

, Checkhigh pressure hose

, Checkdetergentsiphoning hose

, Checkspray gun and assembly for leaks

* Cleandebris

* Checkengine oil level

, Service engineair cleaner2

, Changeengine oil2

, Service spark arrester

, Service spark plug

* Cleancooling system2

Clean if clogged. Replace if perforated or torn.

2Service more often under dirty or dusty conditions.

General Recommendations

Regularmaintenancewill improve the performanceand

extendthe life of the pressure washer. Seeany Searsor

other qualified service dealerfor service.

Thepressure washer warranty doesnot cover items that

havebeen subjectedto operator abuseor negligence.To

receivefull valuefrom the warranty, the operator must

maintain pressure washer as instructed in this manual

including proper storage as detailedin Storage.

Someadjustments will needto be madeperiodically to

properly maintain your pressure washer.

All serviceand adjustments should be madeat least once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTE:Oncea year you should clean or replacethe spark

plug and replacethe air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

DONOTattempt any oil maintenanceon this pump. The

pump is pre-lubricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

EmissionsControl

Maintenance, replacement, or repair ofthe emissions

control devices and systemsmay be performedbyany non-

roadengine repair establishmentor individual. However,

to obtain "no charge" emissions control service, the work

must be performed by a factory authorized dealer.Seethe

Emissions Warranty.

Before Each Use

1. Checkengine oil level.

2. Cleandebris.

3. Checkwater inlet screen for damage.

4. Checkhigh pressure hose for leaks.

5. Checkgun and spray tip extension assemblyfor leaks.

6. Purge pump of air and contaminants.

PRESSUREWASHERMAINTENANCE

Clean Debris

Daily or before use,clean accumulated debris from cleaning

system. Keeplinkage, spring and controls clean. Keeparea

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer. Theseopenings must be kept cleanand

unobstructed.

Cleaningsystem parts should be kept cleanto reducethe risk

of overheating and ignition of accumulated debris.

• Usea dampcloth to wipe exterior surfaces clean.

[ NOTICE

Improper treatment of pressure washer can damageit and

|shorten ts fe.

L DONOTinsertanyobjectsthroughcoolingslots.

• Usea soft bristle brush to loosencaked on dirt, oil, etc.

• Usea vacuumcleanerto pick up loose dirt and debris.

Check and Clean Inlet Screen

Examinegarden hoseinlet screen. Cleanif it is clogged or

replaceif it is torn.

Check High Pressure Hose

High pressure hoses can developleaks from wear, kinking,

or abuse. Inspect hose beforeeach use. Checkfor cuts,

leaks,abrasions, bulging of cover, or damageor movement

of couplings. If any of these conditions exist, replacehose

immediately.

WARHIHG

The high pressure stream of water that this

_ quipment produces cancut through skin and its

underlyingtissues, leadingto serious injury and

_ossibleamputation.

• NEVERrepairhighpressurehose.Replaceit.

, ReplacementhoseratingMUSTexceedmaximumpressure

ratingof unit.

Check Gun and Hozzle Extension

Examinehose connectionto spray gun and makesure it is

secure.Testtrigger by pressing it and making sure it springs

back into placewhenyou releaseit. Do not depress red

button and test trigger. You should not be able to press

trigger. Replacespray gun immediately if it fails any of these

tests.

HozzleMaintenance

A pulsing sensationfelt while squeezingthe spray gun trigger

may becaused by excessivepump pressure. Theprincipal

cause of excessivepump pressure is a spray tip clogged or

restricted with foreign materials, such asdirt, etc. Tocorrect

the problem, immediately cleanthe spray tip following these

instructions:

1. Shut off engine and turn off water supply.

2. ALWAYSpoint spray gun in a safe direction, press red

button and and squeezespray gun trigger to release

retainedhigh water pressure.

WARHIHG

Thehigh pressure stream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leading to serious injury and

possible amputation.

Spraygun traps high water pressure, evenwhen

engine is stopped and water is disconnected,

which cancause injury.

, Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntrigger,to releasehighpressure,every

time youstopengine.

3. Removespray tip from end of nozzleextension.

4. Usea small paperclip to free any foreign material

clogging or restricting spray tip (A).

5. Removenozzleextension from spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through nozzle extension. Back flush

between 30 to 60 seconds.

7. Reinstallspray tip into nozzleextension.

8. Reconnectnozzleextensionto spray gun.

9. Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

10. Start engine following instructions How to Start Your

Pressure Washer.

11. Test pressure washer by operating with eachquick

connect spray tip.

O-Ring Maintenance

Purchasean O-Ring RepairKit atyour local Searsor by

calling 1-800-4-1VIY-HOME(46g-4663) or online at

www.sears.com. It is not included with the pressure washer.

This kit includes replacemento-rings, rubber washer and

water inlet filter. Referto the instruction sheet provided in the

kit to serviceyour unit's o-rings.

WARHIHG

Thehigh pressurestream of water that this

,p_ equipment produces cancut through skin and its

underlyingtissues, leadingto serious injury and

)ossible amputation.

, NEVERrepairleakingconnectionswith sealantof anykind.

Replaceo-ringor seal.

ENGINEMAINTENANCE

WARHIHG

,_J_ Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOUR

PRESSUREWASHER

* Disconnectthesparkplugwirefromthesparkplugandplace

thewirewhereitcannotcontactsparkplug.

WHENTESTINGFOBENGINESPARK

* Useapprovedsparkplugtester.

* DONOTcheckfor sparkwith sparkplugremoved.

0il

Oil Recommendations

We recommendthe useof Briggs & Stratton Warranty

Certified oils for best performance. Otherhigh-quality

detergent oils are acceptableif classified for service SF,SG,

SH, SJ or higher. DONOTusespecial additives.

Outdoortemperatures determine the proper oil viscosity for

the engine. Usethe chart to selectthe best viscosity for the

outdoor temperature rangeexpected.

104 Z__ ,_

86 _

68 o

eoi

5o _

32 _

-4

-22

%_, 40

_1-- 30

__20

_'m _0

l-r =-10

° L--2°

* Below40°F(4°0)theuseofSAE30 will resultin hardstarting.

** Above80°F(27°0)theuseof 10W30maycauseincreasedoil

consumption.Checkoil levelmorefrequently.

NOTE:Synthetic oil meeting ILSACGF-2,API

certification mark and API servicesymbol with

"SJ/CF ENERGYCONSERVING"or higher, is an

acceptableoil at all temperatures. Useof synthetic oil

doesnot alter required oil change intervals.

CheckingOil Level

Oil levelshould be checkedprior to each useor at least every

8 hours of operation. Keepoil level maintained.

1. Makesure pressure washer is on a levelsurface.

2. Removeoil dipstick and wipe dipstick with cleancloth.

Replaceand tighten dipstick. Removeand and check oil

level.

3. Verify oil is at "Full" mark on dipstick. Replaceand

tighten dipstick.

AddingEngineOil

Makesure pressure washer is on a levelsurface.

Checkoil level as described in CheckingOil Level

If needed,slowly pour oil into oil fill openingto the

"Full" mark on dipstick. DONOToverfill.

NOTICE

Overfilling with oil may causethe engineto not start, or

hard starting.

DONOToverfill.

IfovertheFULLmarkon dipstick,drainoil to reduceoil levelto

FULLmarkon dipstick.

4. Replaceand tighten dipstick.

ChangingEngineOil

Changeengine oil after the first 5 hours and every 50 hours

thereafter. If you are using your pressure washer under

extremely dirty or dusty conditions, or in extremely hot

weather, changeoil more often.

CAUTION

Avoid prolonged or repeatedskin contact with used motor

oil.

Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil while engine is still warmfrom running,as

follows:

1. Drainfuel tank by running pressurewasher until fuel

tank is empty.

2. Disconnectspark plug wire and keepit awayfrom spark

plug.

3. Cleanareaaroundoilfill,removeoilfillcap/dipstick.

Wipedipstickclean.

4. Tipyourpressurewashertodrainoilfromoilfillintoa

suitablecontainermakingsureyoutipyourunitaway

fromsparkplug.Whencrankcaseisempty,return

pressurewashertouprightposition.

5. Slowlypourrecommendedoil(about18oz.)intooilfill

opening.Pausetopermitoiltosettle.Fillto"Full"mark

ondipstick.

6. Wipedipstickcleaneachtimeoillevelischecked.DO

NOToverfill.

7. Replaceandtightendipstick.

8. Wipeupanyremainingoil.

9. Reconnectsparkplugwiretosparkplug.

Service Air Cleaner

Your enginewill not run properly and may be damagedif you

run it with a dirty air cleaner.

Servicethe air cleaneronce every 25 hours of operation or

once eachyear, whichever comes first. Service more often if

operating under dirty or dusty conditions. Replacementsare

availableatyour local Searsservicecenter.

To servicethe air cleaner, foigewthese steps:

1. Loosenscrew (A) and tilt cover (B) down.

2. Carefully removecartridge (C)assembly.

3. Toclean cartridge, gently tap pleatedpaper side on a flat

surface.

4. Reinstallclean or new cartridge assembly insidecover.

5. Insert cover's tabs (8) into slots in bottom of base (E).

6. Tilt cover up and tighten screw securelyto base.

NOTE:You can purchase newair filter elements by calling

1-SOO-4-MY-HOME(469-4663).

Service Spark Plug

Servicethe spark plug every 1O0hours of operation or

yearly, whichever occurs first.

1. Cleanareaaround spark plug.

2. Removeand inspect spark plug.

3. Replacespark plug if electrodesare pitted, burned or

porcelainis cracked. Usethe recommended replacement

plug. See Specifications.

4. Checkelectrode gap with wire feelergauge and set spark

plug gap to 0.030 inch (0.76 mm) if necessary.

5. Install spark plug and tighten firmly.

NOTE:You canpurchase a new spark plug bycalling

1-800-4-MY-HOME(469-4663).

Spark Arrester Service

Your engine is not factory-equipped with a spark arrester, in

some areas,it is illegal to operatean engine without a spark

arrester. Checklocal laws and regulations. A spark arrester is

availablefrom your nearest Searsservicecenter. If you need

to order a spark arrester, pleasecall 1-SO8-4-MY-NOME

(469-4663).

Thespark arrester must be serviced every50 hours to keepit

functioning asdesigned.

If the engine hasbeen running, the muffler will be very hot.

Allow the muffler to cool before servicingthe spark arrester.

WARHIHG

_ ontact with muffler area can result in serious

burns.

_ Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing a fire.

* DONOTtouchhotpartsandAVOIDhotexhaustgases.

* Allowequipmenttocoolbeforetouching.

* Keepatleast5 feet(152cm) ofclearanceonall sidesof

pressurewasherincludingoverhead.

* Codeof FederalRegulation(CFR)Title36Parks,Forests,and

PublicPropertyrequireequipmentpoweredbyaninternal

combustionengineto haveasparkarrester,maintainedin

effectiveworkingorder,complyingto USDAForestservice

standard5100-1Cor laterrevision.IntheStateof Californiaa

sparkarresterisrequiredundersection4442oftheCalifornia

Publicresourcescode.Otherstatesmayhavesimilarlaws.

Removespark arresterscreenfor cleaningand inspection.

Replaceif screen is damaged.

Air Cooling System

Overtime debris may accumulate in cylinder cooling fins and

cannot be observed without partial engine disassembly. For

this reason,we recommendyou havea qualified Sears

servicedealer cleanthe cooling system per recommended

intervals (see MaintenanceSchedule). Equallyimportant is to

keeptop of engine freefrom debris. See CleanDebris.

Keepareaswithin heavyline clearof debris.

AFTEREACHUSE

Water should not remain in the unit for long periods of time.

Sedimentsor minerals candeposit on pump parts and

"freeze" pump action. Followthese procedures after every

use:

1. Flush detergentsystem byturning its detergent shut-off

valveto "Off" position and run pressure washer with

black detergent spray tip. Flushfor one to two minutes.

Shut off engine,turn off water supply, point gun in a

safe direction, press red button and squeezetrigger to

relievetrapped pressure and let engine cool.

WARHIHG

Thehigh pressurestream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leadingto serious injury and

)ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

. Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressred button

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustop engine.

3. Disconnect hosefrom spray gun and high pressure

outlet on pump. Drainwater from hose, gun, and nozzle

extension. Usea rag to wipe off the hose.

4. Empty pump of all pumped liquids by pulling recoil

handle about6 times. This should remove most liquid in

pump.

5. Coil high pressure hoseand properly hang it on hook

provided on handle.

6. Store unit in a clean, dry area.

7. If storing for morethan 30 dayssee Long Term Storage

on next page.

WARHIHG

Fue]and itsvapors are extremely flammable and

explosive.

_j_ ire or explosion cancause severeburns or

death.

WHENSTORINGFUELOREQUIPMENTWITH FUELIN TANK

* Storeawayfromfurnaces,stoves,waterheaters,clothes

dryers,or otherappliancesthathavepilotlightor otherignition

sourcebecausetheycanignitefuelvapors.

Page is loading ...

Craftsman 580.752131 Owner's manual

Brand: Craftsman

Model: 580.752131

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752131

Download PDF

report

in other languages

español: Craftsman 580.752131 El manual del propietario

Craftsman 580.752131 Owner's manual

This manual is also suitable for

Craftsman 580.752131 Owner's manual

in other languages

Related papers

Other documents