WEG MW500 Quick start guide

Frequency Inverter

Convertidor de Frecuencia

Inversor de Frequência

MW500 V1.5X

Motors | Automation | Energy | Transmission & Distribution | Coatings

Quick Reference of Parameters, Alarms and Faults

Referencia Rápida de los Parámetros, Alarmas y Fallas

Referência Rápida dos Parâmetros, Alarmes e Falhas

Quick Reference of Parameters,

Alarms and Faults

Series: MW500

Language: English

Document: 10002164964 / 01

Software Version: 1.5X

Date: 03/2014

English

Page is loading ...

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 5

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0000 Access to Parameters 0 to 9999 0

P0001 Speed Reference 0 to 65535 ro READ

P0002 Motor Speed 0 to 65535 ro READ

P0003 Motor Current 0.0 to 200.0 A ro READ

P0004 DC Link Voltage (Ud) 0 to 2000 V ro READ

P0005 Motor Frequency 0.0 to 500.0 Hz ro READ

P0006 VFD Status 0 = Ready

1 = Run

2 = Undervoltage

3 = Fault

4 = Self-Tuning

5 = Conﬁguration

6 = DC-Braking

7 = Sleep Mode

ro READ

P0007 Motor Voltage 0 to 2000 V ro READ

P0009 Motor Torque -1000.0 to 1000.0 % ro, V V W READ

P0010 Output Power 0.0 to 6553.5 kW ro READ

P0011 Power Factor -1.00 to 1.00 ro READ

P0012 DI8 to DI1 Status Bit 0 = DI1

Bit 1 = DI2

Bit 2 = DI3

Bit 3 = DI4

Bit 4 = DI5

Bit 5 = DI6

Bit 6 = DI7

Bit 7 = DI8

ro READ, I/O

P0013 DO5 to DO1 Status Bit 0 = DO1

Bit 1 = DO2

Bit 2 = DO3

Bit 3 = DO4

Bit 4 = DO5

ro READ, I/O

P0014 AO1 Value 0.0 to 100.0 % ro READ, I/O

P0015 AO2 Value 0.0 to 100.0 % ro READ, I/O

P0016 FO % Value 0.0 to 100.0 % ro READ, I/O

P0017 FO Hz Value 0 to 20000 Hz ro READ, I/O

P0018 AI1 Value -100.0 to 100.0 % ro READ, I/O

P0019 AI2 Value -100.0 to 100.0 % ro READ, I/O

P0020 AI3 Value -100.0 to 100.0 % ro READ, I/O

P0021 FI % Value -100.0 to 100.0 % ro READ, I/O

P0022 FI Hz Value 0 to 20000 Hz ro READ, I/O

P0023 Main SW Version 0.00 to 655.35 ro READ

P0024 Sec. SW Version 0.00 to 655.35 ro READ

P0027 Plug-in Mod. Conﬁg. 0 = No Plug-in

1 = CFW500-IOS

2 = CFW500-IOD

3 = CFW500-IOAD

4 = CFW500-IOR

5 = CFW500-CUSB

6 = CFW500-CCAN

7 = CFW500-CRS232

8 = CFW500-CPDP

9 = CFW500-CRS485

10 to 63 = No Plug-in

ro READ

Quick Reference of Parameters, Alarms and Faults

English

6 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0029 Power HW Conﬁg. 0 = Not Identiﬁed

1 = 200-240 V / 1.6 A

2 = 200-240 V / 2.6 A

3 = 200-240 V / 4.3 A

4 = 200-240 V / 7.0 A

5 = 200-240 V / 9.6 A

6 = 380-480 V / 1.0 A

7 = 380-480 V / 1.6 A

8 = 380-480 V / 2.6 A

9 = 380-480 V / 4.0 A

10 = 380-480 V / 6.1 A

11 = 200-240 V / 7.3 A

12 = 200-240 V / 10.0 A

13 = 200-240 V / 16.0 A

14 = 380-480 V / 2.7 A

15 = 380-480 V / 4.3 A

16 = 380-480 V / 6.5 A

17 = 380-480 V / 10.0 A

18 = 200-240 V / 24.0 A

19 = 380-480 V / 14.0 A

20 = 380-480 V / 16.0 A

21 = 500-600 V / 1.7 A

22 = 500-600 V / 3.0 A

23 = 500-600 V / 4.3 A

24 = 500-600 V / 7.0 A

25 = 500-600 V / 10.0 A

26 = 500-600 V / 12.0 A

27 = 200-240 V / 28.0 A

28 = 200-240 V / 33.0 A

29 = 380-480 V / 24.0 A

30 = 380-480 V / 30.0 A

31 = 500-600 V / 17.0 A

32 = 500-600 V / 22.0 A

33 = 200-240 V / 45.0 A

34 = 200-240 V / 54.0 A

35 = 380-480 V / 38.0 A

36 = 380-480 V / 45.0 A

37 = 500-600 V / 27.0 A

38 = 500-600 V / 32.0 A

According to

inverter model

ro READ

P0030 Heatsink Temperature -20 to 150 ºC ro READ

P0036 Fan Heatsink Speed 0 to 15000 rpm ro READ

P0037 Motor Overload Ixt 0 to 100 % ro READ

P0040 PID Process Variable 0.0 to 3000.0 ro READ

P0041 PID Setpoint Value 0.0 to 3000.0 ro READ

P0045 Fan Enabled Time 0 to 65535 h ro READ

P0047 CONFIG Status 0 to 999 ro READ

P0048 Present Alarm 0 to 999 ro READ

P0049 Present Fault 0 to 999 ro READ

P0050 Last Fault 0 to 999 ro READ

P0051 Current at Last Fault 0.0 to 200.0 A ro READ

P0052 DC Link at Last Fault 0 to 2000 V ro READ

P0053 Frequency at Last Fault 0.0 to 500.0 Hz ro READ

P0054 Temp. at Last Fault -20 to 150 ºC ro READ

P0055 Log. State Last Fault 0000h to FFFFh ro READ

P0060 Second Fault 0 to 999 ro READ

P0061 Current at 2

nd

Fault 0.0 to 200.0 A ro READ

P0062 DC Link at 2

nd

Fault 0 to 2000 V ro READ

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 7

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0063 Frequency 2

nd

Fault 0.0 to 500.0 Hz ro READ

P0064 Temp. 2

nd

Fault -20 to 150 ºC ro READ

P0065 Log. State 2

nd

Fault 0000h to FFFFh ro READ

P0070 Third Fault 0 to 999 ro READ

P0071 Current at 3

rd

Fault 0.0 to 200.0 A ro READ

P0072 DC Link 3

rd

Fault 0 to 2000 V ro READ

P0073 Frequency 3

rd

Fault 0.0 to 500.0 Hz ro READ

P0074 Temp. 3

rd

Fault -20 to 150 ºC ro READ

P0075 Log. State 3

rd

Fault 0000h to FFFFh ro READ

P0100 Acceleration Time 0.1 to 999.0 s 10.0 s BASIC

P0101 Deceleration Time 0.1 to 999.0 s 10.0 s BASIC

P0102 2

nd

Ramp Accel. Time 0.1 to 999.0 s 10.0 s

P0103 2

nd

Ramp Decel. Time 0.1 to 999.0 s 10.0 s

P0104 S Ramp 0 = Inactive

1 = Active

0 cfg

P0105 1

st

/2

nd

Ramp Sel. 0 = First Ramp

1 = Second Ramp

2 = DIx

3 = Serial/USB

4 = Reserved

5 = CO/DN/DP

6 = SoftPLC

3 I/O

P0106 3

rd

Ramp Accel. Time 0.1 to 999.0 s 5.0 s

P0120 Speed Ref. Backup 0 = Inactive

1 = Active

2 = Backup by P0121

1

P0121 Speed Reference via HMI 0.0 to 500.0 Hz 3.0 Hz

P0122 Speed Reference for JOG -500.0 to 500.0 Hz 5.0 Hz

P0124 Multispeed Ref. 1 -500.0 to 500.0 Hz 3.0 Hz

P0125 Multispeed Ref. 2 -500.0 to 500.0 Hz 10.0 (5.0) Hz

P0126 Multispeed Ref. 3 -500.0 to 500.0 Hz 20.0 (10.0) Hz

P0127 Multispeed Ref. 4 -500.0 to 500.0 Hz 30.0 (20.0) Hz

P0128 Multispeed Ref. 5 -500.0 to 500.0 Hz 40.0 (30.0) Hz

P0129 Multispeed Ref. 6 -500.0 to 500.0 Hz 50.0 (40.0) Hz

P0130 Multispeed Ref. 7 -500.0 to 500.0 Hz 60.0 (50.0) Hz

P0131 Multispeed Ref. 8 -500.0 to 500.0 Hz 66.0 (55.0) Hz

P0133 Minimum Speed 0.0 to 500.0 Hz 3.0 Hz BASIC

P0134 Maximum Speed 0.0 to 500.0 Hz 66.0 (55.0) Hz BASIC

P0135 Max. Output Current 0.0 to 200.0 A 1.5xI

nom

BASIC,

MOTOR

P0136 Manual Torque Boost 0.0 to 30.0 % According to

inverter model

V/f BASIC,

MOTOR

P0137 Autom. Torque Boost 0.0 to 30.0 % 0.0 % V/f MOTOR

P0138 Slip Compensation -10.0 to 10.0 % 0.0 % V/f MOTOR

P0139 Output Current Filter 0 to 9999 ms 50 ms

P0140 Output Current Filter 0 to 9999 ms 500 ms VVW

P0142 Max. Output Voltage 0.0 to 100.0 % 100.0 % cfg, V/f

P0143 Interm. Output Voltage 0.0 to 100.0 % 66.7 % cfg, V/f

P0144 Minim. Output Voltage 0.0 to 100.0 % 33.3 % cfg, V/f

Quick Reference of Parameters, Alarms and Faults

English

8 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0145 Field Weakening Frequency 0.0 to 500.0 Hz 60.0 (50.0) Hz cfg, V/f

P0146 Intermediate Frequency 0.0 to 500.0 Hz 40.0 (33.3) Hz cfg, V/f

P0147 Low Output Frequency 0.0 to 500.0 Hz 20.0 (16.7) Hz cfg, V/f

P0150 Type DC V/f Link Regulator 0 = hold_Ud and dec_LC

1 = accel_Ud and dec_LC

2 = hold_Ud and hold_LC

3 = accel_Ud and hold_LC

0 cfg MOTOR

P0151 DC Link Regul. Level 339 to 1200 V 400 V (P0296 = 0)

800 V (P0296 = 1)

1000 V (P0296 = 2)

MOTOR

P0152 DC Link Regul. Prop. Gain 0.00 to 9.99 1.50 MOTOR

P0153 Dyn. Braking Level 339 to 1200 V 375 V (P0296 = 0)

750 V (P0296 = 1)

950 V (P0296 = 2)

MOTOR

P0156 Overl. Curr. 100 % Speed 0.0 to 200.0 A 1.1xI

nom

MOTOR

P0157 Overl. Curr. 50 % Speed 0.0 to 200.0 A 1.0xI

nom

MOTOR

P0158 Overl. Curr. 20 % Speed 0.0 to 200.0 A 0.8xI

nom

MOTOR

P0178 Rated Flux 0.0 to 150.0 % 100.0 % MOTOR

P0200 Password 0 = Inactive

1 = Active

1 to 9999 = New

Password

0 HMI

P0202 Control Type 0 = V/f

1 to 4 = Not Used

5 = VV W

0 cfg STARTUP

P0203 Special Function Sel. 0 = None

1 = PID via AI1

2 = PID via AI3

3 = PID via FI

0 cfg

P0204 Load/Save Parameters 0 and 1 = Not Used

2 = Reset P0045

3 and 4 = Not Used

5 = Load WEG 60 Hz

6 = Load WEG 50 Hz

7 = Load User 1

8 = Load User 2

9 = Save User 1

10 = Save User 2

0 cfg

P0205 Main Display Parameter 0 to 1500 2 HMI

P0206 Secondary Parameter

Display

0 to 1500 1 HMI

P0207 Parameter for Bar 0 to 1500 3 HMI

P0208 Ref. Scale Factor 1 to 65535 600 (500) HMI

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 9

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0209 Ref. Eng. Unit 0 = None

1 = V

2 = A

3 = rpm

4 = s

5 = ms

6 = N

7 = m

8 = Nm

9 = mA

10 = %

11 = ºC

12 = CV

13 = Hz

14 = HP

15 = h

16 = W

17 = kW

18 = kWh

19 = H

13 HMI

P0210 Ref. Indication Form 0 = wxyz

1 = wxy.z

2 = wx.yz

3 = w.xyz

1 HMI

P0213 Bar Scale Factor 1 to 65535 According to

inverter model

(P0295)

HMI

P0216 HMI Backlight 0 = OFF

1 = ON

1 cfg HMI

P0217 Sleep Mode Frequency 0.0 to 500.0 Hz 0.0 Hz

P0218 Sleep Mode Time 0 to 999 s 0 s

P0220 LOC/REM Selection Source 0 = Always LOC.

1 = Always REM.

2 = HMI Key (LOC)

3 = HMI Key (REM)

4 = DIx

5 = Serial/USB (LOC)

6 = Serial/USB (REM)

7 = Not Used

8 = Not Used

9 = CO/DN/DP (LOC)

10 = CO/DN/DP (REM)

11 = SoftPLC

4 cfg I/O

P0221 LOC Reference Sel. 0 = Keypad

1 = AI1

2 = AI2

3 = AI3

4 = FI

5 = AI1 + AI2 > 0

6 = AI1 + AI2

7 = E.P.

8 = Multispeed

9 = Serial/USB

10 = Not Used

11 = CO/DN/DP

12 = SoftPLC

13 = Not Used

14 = AI1 > 0

15 = AI2 > 0

16 = AI3 > 0

17 = FI > 0

18 = Knob

18 cfg I/O

Quick Reference of Parameters, Alarms and Faults

English

10 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0222 REM Reference Sel. See options in P0221 9 cfg I/O

P0223 LOC FWD/REV Selection 0 = Always FWD

1 = Always REV

2 = HMI Key (FWD)

3 = HMI Key (REV)

4 = DIx

5 = Serial/USB (FWD)

6 = Serial/USB (REV)

7 = Not Used

8 = Not Used

9 = CO/DN/DP (FWD)

10 = CO/DN/DP (REV)

11 = Not Used

12 = SoftPLC

4 cfg I/O

P0224 LOC Run/Stop Sel. 0 = HMI Key

1 = DIx

2 = Serial/USB

3 = Not Used

4 = CO/DN/DP

5 = SoftPLC

1 cfg I/O

P0225 LOC JOG Selection 0 = Disable

1 = HMI Key

2 = DIx

3 = Serial/USB

4 = Not Used

5 = CO/DN/DP

6 = SoftPLC

1 cfg I/O

P0226 REM FWD/REV Selection See options in P0223 5 cfg I/O

P0227 REM Run/Stop Sel. See options in P0224 2 cfg I/O

P0228 REM JOG Selection See options in P0225 3 cfg I/O

P0229 Stop Mode Selection 0 = By Ramp

1 = Coast

2 = Quick Stop

0 cfg I/O

P0230 Dead Zone (AIs) 0 = Inactive

1 = Active

0 cfg I/O

P0231 AI1 Signal Function 0 = Speed Ref.

1 = Not Used

2 = Not Used

3 = Not Used

4 = PTC

5 = Not Used

6 = Not Used

7 = SoftPLC

8 = Function 1 Application

9 = Function 2 Application

10 = Function 3 Application

11 = Function 4 Application

12 = Function 5 Application

13 = Function 6 Application

14 = Function 7 Application

15 = Function 8 Application

0 cfg I/O

P0232 AI1 Gain 0.000 to 9.999 1.000 I/O

P0233 AI1 Signal Type 0 = 0 to 10 V / 20 mA

1 = 4 to 20 mA

2 = 10 V / 20 mA to 0

3 = 20 to 4 mA

0 I/O

P0234 AI1 Offset -100.0 to 100.0 % 0.0 % I/O

P0235 AI1 Filter 0.00 to 16.00 s 0.00 s I/O

P0236 AI2 Signal Function See options in P0231 0 cfg I/O

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 11

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0237 AI2 Gain 0.000 to 9.999 1.000 I/O

P0238 AI2 Signal Type See options in P0233 0 I/O

P0239 AI2 Offset -100.0 to 100.0 % 0.0 % I/O

P0240 AI2 Filter 0.00 to 16.00 s 0.00 s I/O

P0241 AI3 Signal Function See options in P0231 0 cfg I/O

P0242 AI3 Gain 0.000 to 9.999 1.000 I/O

P0243 AI3 Input Signal 0 = 0 to 10 V / 20 mA

1 = 4 to 20 mA

2 = 10 V / 20 mA to 0

3 = 20 to 4 mA

4 = -10 V to +10 V

0 I/O

P0244 AI3 Offset -100.0 to 100.0 % 0.0 % I/O

P0245 AI3 Filter 0.00 to 16.00 s 0.00 s I/O

P0246 Freq. Input FI 0 = Inactive

1 = Active

0 I/O

P0247 FI Gain 0.000 to 9.999 1.000 I/O

P0248 Min. FI 10 to 20000 Hz 10 Hz I/O

P0249 FI Offset -100.0 to 100.0 % 0.0 % I/O

P0250 Max. FI 10 to 20000 Hz 10000 Hz I/O

P0251 AO1 Function 0 = Speed Ref.

1 = Not Used

2 = Real Speed

3 = Not Used

4 = Not Used

5 = Output Current

6 = Process Var.

7 = Active Current

8 = Not Used

9 = PID Setpoint

10 = Not Used

11 = Motor Torque

12 = SoftPLC

13 = Not Used

14 = Not Used

15 = Not Used

16 = Motor Ixt

17 = Not Used

18 = P0696 Value

19 = P0697 Value

20 = P0698 Value

21 = Function 1 Application

22 = Function 2 Application

23 = Function 3 Application

24 = Function 4 Application

25 = Function 5 Application

26 = Function 6 Application

27 = Function 7 Application

28 = Function 8 Application

2 I/O

P0252 AO1 Gain 0.000 to 9.999 1.000 I/O

P0253 AO1 Signal Type 0 = 0 to 10 V

1 = 0 to 20 mA

2 = 4 to 20 mA

3 = 10 V to 0

4 = 20 to 0 mA

5 = 20 to 4 mA

0 I/O

P0254 AO2 Function See options in P0251 5 I/O

P0255 AO2 Gain 0.000 to 9.999 1.000 I/O

Quick Reference of Parameters, Alarms and Faults

English

12 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0256 AO2 Signal Type See options in P0253 0 I/O

P0257 FO Function 0 = Speed Ref.

1 = Not Used

2 = Real Speed

3 = Not Used

4 = Not Used

5 = Output Current

6 = Process Var.

7 = Active Current

8 = Not Used

9 = PID Setpoint

10 = Not Used

11 = Motor Torque

12 = SoftPLC

13 = Not Used

14 = Not Used

15 = Disable FO

16 = Motor Ixt

17 = Not Used

18 = Value of P0696

19 = Value of P0697

20 = Value of P0698

21 = Function 1 Application

22 = Function 2 Application

23 = Function 3 Application

24 = Function 4 Application

25 = Function 5 Application

26 = Function 6 Application

27 = Function 7 Application

28 = Function 8 Application

15 I/O

P0258 FO Gain 0.000 to 9.999 1.000 I/O

P0259 Min. FO 10 to 20000 Hz 10 Hz I/O

P0260 Max. FO 10 to 20000 Hz 10000 Hz I/O

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 13

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0263 DI1 Function 0 = Not Used

1 = Run/Stop

2 = General Enable

3 = Quick Stop

4 = FWD Run

5 = REV Run

6 = Start

7 = Stop

8 = Clockwise Rotation Dir

9 = LOC/REM

10 = JOG

11 = Increase E.P.

12 = Decrease E.P.

13 = Multispeed

14 = 2

nd

Ramp

15 = Not Used

16 = Not Used

17 = Not Used

18 = No Ext. Alarm

19 = No Ext. Fault

20 = Reset

21 = SoftPLC

22 = Manual/Auto PID

23 = Not Used

24 = Disable Flying Start

25 = Not Used

26 = Program. Off

27 = Load User 1

28 = Load User 2

29 = PTC

30 = Not Used

31 = Not Used

32 = 2

nd

Ramp Multispeed

33 = 2

nd

Ramp E.P. Ac.

34 = 2

nd

Ramp E.P. De.

35 = 2

nd

Ramp FWD Run

36 = 2

nd

Ramp REV Run

37 = Start / Inc. E.P.

38 = Dec. E.P. / Stop

39 = Function 1 Application

40 = Function 2 Application

41 = Function 3 Application

42 = Function 4 Application

43 = Function 5 Application

44 = Function 6 Application

45 = Function 7 Application

46 = Function 8 Application

1 cfg I/O

P0264 DI2 Function See options in P0263 8 cfg I/O

P0265 DI3 Function See options in P0263 20 cfg I/O

P0266 DI4 Function See options in P0263 9 cfg I/O

P0267 DI5 Function See options in P0263 0 cfg I/O

P0268 DI6 Function See options in P0263 0 cfg I/O

P0269 DI7 Function See options in P0263 0 cfg I/O

P0270 DI8 Function See options in P0263 0 cfg I/O

Quick Reference of Parameters, Alarms and Faults

English

14 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0271 DIs Signal 0 = All DIx are NPN

1 = DI1-PNP

2 = (DI1...DI2) PNP

3 = (DI1...DI3) PNP

4 = (DI1...DI4) PNP

5 = (DI1...DI5) PNP

6 = (DI1...DI6) PNP

7 = (DI1...DI7) PNP

8 = All DIx are PNP

0 cfg I/O

P0275 DO1 Output Function 0 = Not Used

1 = F* > Fx

2 = F > Fx

3 = F < Fx

4 = F = F*

5 = Not Used

6 = Is > Ix

7 = Is < Ix

8 = Torque > Tx

9 = Torque < Tx

10 = Remote

11 = Run

12 = Ready

13 = No Fault

14 = No F0070

15 = Not Used

16 = No F0021/22

17 = Not Used

18 = No F0072

19 = 4-20 mA OK

20 = P0695 Value

21 = Forward

22 = Proc. V. > VPx

23 = Proc. V. < VPx

24 = Ride-Through

25 = Pre-Charge OK

26 = Fault

27 = Not Used

28 = SoftPLC

29 to 34 = Not Used

35 = No Alarm

36 = No Fault/Alarm

37 = Function 1 Application

38 = Function 2 Application

39 = Function 3 Application

40 = Function 4 Application

41 = Function 5 Application

42 = Function 6 Application

43 = Function 7 Application

44 = Function 8 Application

13 I/O

P0276 DO2 Function See options in P0275 2 I/O

P0277 DO3 Function See options in P0275 0 I/O

P0278 DO4 Function See options in P0275 0 I/O

P0279 DO5 Function See options in P0275 0 I/O

P0287 Fx Hysteresis 0.0 to 500.0 Hz 0.5 Hz I/O

P0288 Fx Speed 0.0 to 500.0 Hz 3.0 Hz I/O

P0290 Ix Current 0.0 to 200.0 A 1.0xI

nom

I/O

P0293 Tx Torque 0 to 200 % 100 % I/O

P0295 VFD Rated Curr. 0.0 to 200.0 A According to

inverter model

ro READ

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 15

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0296 Power Supply Rated Voltage 0 = 200 - 240 V

1 = 380 - 480 V

2 = 500 - 600 V

According to

inverter model

ro, cfg READ

P0297 Switching Frequency 1500 to 15000 Hz 4000 Hz

P0299 DC-Braking Start Time 0.0 to 15.0 s 0.0 s

P0300 DC-Braking Stop Time 0.0 to 15.0 s 0.0 s

P0301 DC-Braking Frequency 0.0 to 500.0 Hz 3.0 Hz

P0302 DC Braking Voltage 0.0 to 100.0 % 20.0 %

P0303 Skip Frequency 1 0.0 to 500.0 Hz 20.0 Hz

P0304 Skip Frequency 2 0.0 to 500.0 Hz 30.0 Hz

P0306 Skip Band 0.0 to 25.0 Hz 0.0 Hz

P0308 Serial Address 1 to 247 1 NET

P0310 Serial Baud Rate 0 = 9600 bits/s

1 = 19200 bits/s

2 = 38400 bits/s

1 NET

P0311 Serial Bytes Conﬁg. 0 = 8 bits, no, 1

1 = 8 bits, even, 1

2 = 8 bits, odd, 1

3 = 8 bits, no, 2

4 = 8 bits, even, 2

5 = 8 bits, odd, 2

1 NET

P0312 Serial Protocol (1)(2) 0 = HMIR (1)

1 = Reserved

2 = Modbus RTU (1)

3 = Reserved

4 = Reserved

5 = Reserved

6 = HMI(1) + Modbus

RTU (2)

7 = Modbus RTU (2)

2 cfg NET

P0313 Comm. Error Action 0 = Inactive

1 = Ramp Stop

2 = General Disab.

3 = Go to LOC

4 = LOC Keep Enab.

5 = Cause Fault

1 NET

P0314 Serial Watchdog 0.0 to 999.0 s 0.0 s NET

P0316 Serial Interf. Status 0 = Inactive

1 = Active

2 = Watchdog Error

NET

P0320 Flying Start/Ride-Through 0 = Inactive

1 = Flying Start (FS)

2 = FS and RT

3 = Ride-Through (RT)

0 cfg

P0331 Voltage Ramp 0.2 to 60.0 s 2.0 s

P0340 Auto-Reset Time 0 to 255 s 0 s

P0343 Fault Mask 0000h to FFFFh

Bit 0 = F0074

Bit 1 = F0048

Bit 2 = F0078

Bit 3 = F0079

Bit 4 = F0076

Bit 5 = F0179

Bit 6 to 15 = Reserved

0007h cfg

P0349 Ixt Alarm Level 70 to 100 % 85 % cfg

Quick Reference of Parameters, Alarms and Faults

English

16 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0397 Control Conﬁg. Bit 0 = Slip Compens.

Regen.

Bit 1 = Dead Time

Compensation

Bit 2 = Io Stabilization

Bit 3 = Red. P0297 on

A0050

Bit 4 = Enable Fan

Bit 5 = Control Fan

003Fh cfg

P0399 Motor Rated Eff. 50.0 to 99.9 % 75.0 % cfg, VVW MOTOR,

STARTUP

P0400 Motor Rated Voltage 200 to 600 V According to

Figure 10.2 on

page 10-10

cfg, V V W MOTOR,

STARTUP

P0401 Motor Rated Current 0.0 to 200.0 A 1.0xI

nom

cfg MOTOR,

STARTUP

P0402 Motor Rated Speed 0 to 30000 rpm 1710 (1425) rpm cfg MOTOR,

STARTUP

P0403 Motor Rated Frequency 0 to 500 Hz 60 Hz (50) Hz cfg MOTOR,

STARTUP

P0404 Motor Rated Power 0 = 0.16 HP (0.12 kW)

1 = 0.25 HP (0.19 kW)

2 = 0.33 HP (0.25 kW)

3 = 0.5 HP (0.37 kW)

4 = 0.75 HP (0.55 kW)

5 = 1 HP (0.75 kW)

6 = 1.5 HP (1.1 kW)

7 = 2 HP (1.5 kW)

8 = 3 HP (2.2 kW)

9 = 4 HP (3 kW)

10 = 5 HP (3.7 kW)

11 = 5.5 HP (4 kW)

12 = 6 HP (4.5 kW)

13 = 7.5 HP (5.5 kW)

14 = 10 HP (7.5 kW)

15 = 12.5 HP (9 kW)

16 = 15 HP (11 kW)

17 = 20 HP (15 kW)

18 = 25 HP (18.5 kW)

19 = 30 HP (22 kW)

According to

inverter model

cfg, V V W MOTOR,

STARTUP

P0406 Motor Ventilation 0 = Self-Vent.

1 = Separate Vent.

0 cfg MOTOR,

STARTUP

P0407 Motor Rated Power Fac. 0.50 to 0.99 0.80 cfg, VVW MOTOR,

STARTUP

P0408 Run Self-Tuning 0 = No

1 = Yes

0 cfg, V VW MOTOR,

STARTUP

P0409 Stator Resistance 0.01 to 99.99 Ω According to

inverter model

cfg, V V W MOTOR,

STARTUP

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 17

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0510 SoftPLC Eng. Unit 1 0 = None

1 = V

2 = A

3 = rpm

4 = s

5 = ms

6 = N

7 = m

8 = N.m

9 = mA

10 = %

11 = °C

12 = CV

13 = Hz

14 = HP

15 = h

16 = W

17 = kW

18 = kWh

19 = H

13 HMI,

SPLC

P0511 Decimal Point Unit Eng. 1 0 = wxyz

1 = wxy.z

2 = wx.yz

3 = w.xyz

1 HMI,

SPLC

P0512 SoftPLC Eng. Unit 2 See options in P0510 13 HMI,

SPLC

P0513 Decimal Point Unit Eng. 2 0 = wxyz

1 = wxy.z

2 = wx.yz

3 = w.xyz

1 HMI,

SPLC

P0520 PID Proportional Gain 0.000 to 9.999 1.000

P0521 PID Integral Gain 0.000 to 9.999 0.430

P0522 PID Differential Gain 0.000 to 9.999 0.000

P0525 Keypad PID Setpoint 0.0 to 100.0 % 0.0 %

P0526 PID Setpoint Filter 0 to 9999 ms 50 ms

P0527 PID Action Type 0 = Direct

1 = Reverse

0

P0528 VP Scale Factor 10 to 30000 1000 HMI

P0529 VP Indication Form 0 = wxyz

1 = wxy.z

2 = wx.yz

3 = w.xyz

1 HMI

P0533 PVx Value 0.0 to 100.0 % 90.0 % I/O

P0535 Wake Up Band 0.0 to 100.0 % 0.0 % I/O

P0536 P0525 Autom. Setting 0 = Inactive

1 = Active

0 cfg

Quick Reference of Parameters, Alarms and Faults

English

18 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0680 Logical Status Bit 0 = Reserved

Bit 1 = Run Command

Bit 2 and 3 = Reserved

Bit 4 = Quick Stop

Bit 5 = 2

nd

Ramp

Bit 6 = Conﬁg. Mode

Bit 7 = Alarm

Bit 8 = Running

Bit 9 = Enabled

Bit 10 = Forward

Bit 11 = JOG

Bit 12 = Remote

Bit 13 = Undervoltage

Bit 14 = Automatic (PID)

Bit 15 = Fault

ro READ,

NET

P0681 Speed at 13 bits -32768 to 32767 ro NET

P0682 Serial/USB Control Bit 0 = Ramp Enable

Bit 1 = General Enable

Bit 2 = Run Forward

Bit 3 = JOG Enable

Bit 4 = Remote

Bit 5 = 2

nd

Ramp

Bit 6 = Quick Stop

Bit 7 = Fault Reset

Bit 8 to 15 = Reserved

ro NET

P0683 Serial/USB Ref. Speed -32768 to 32767 ro NET

P0684 CO/DN Control See options in P0682 ro NET

P0685 CO/DN Speed Ref -32768 to 32767 ro NET

P0690 Logical Status 2 Bit 0 to 3 = Reserved

Bit 4 = Force Low Fs

Bit 5 = Sleep Mode

Bit 6 = Deceleration Ramp

Bit 7 = Acceleration Ramp

Bit 8 = Freeze Ramp

Bit 9 = Setpoint Ok

Bit 10 = DC Link Regulation

Bit 11 = 50 Hz Conﬁg.

Bit 12 = Ride-Through

Bit 13 = Flying Start

Bit 14 = DC Braking

Bit 15 = PWM

ro READ,

NET

P0695 DOx Value Bit 0 = DO1

Bit 1 = DO2

Bit 2 = DO3

Bit 3 = DO4

Bit 4 = DO5

ro NET

P0696 AOx Value 1 -32768 to 32767 ro NET

P0697 AOx Value 2 -32768 to 32767 ro NET

P0698 AOx Value 3 -32768 to 32767 ro NET

P0700 CAN Protocol 1 = CANopen

2 = DeviceNet

2 NET

P0701 CAN Address 0 to 127 63 NET

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 19

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0702 CAN Baud Rate 0 = 1 Mbps/Auto

1 = Reserved/Auto

2 = 500 Kbps

3 = 250 Kbps

4 = 125 Kbps

5 = 100 Kbps/Auto

6 = 50 Kbps/Auto

7 = 20 Kbps/Auto

8 = 10 Kbps/Auto

0 NET

P0703 Bus Off Reset 0 = Manual

1 = Automatic

0 NET

P0705 CAN Controller Status 0 = Disable

1 = Auto-baud

2 = CAN Enabled

3 = Warning

4 = Error Passive

5 = Bus Off

6 = No Bus Power

ro NET

P0706 RX CAN Telegrams 0 to 65535 ro NET

P0707 TX CAN Telegrams 0 to 65535 ro NET

P0708 Bus Off Counter 0 to 65535 ro NET

P0709 CAN Lost Messages 0 to 65535 ro NET

P0710 DNet I/O instances 0 = ODVA Basic 2W

1 = ODVA Extend 2W

2 = Manuf. Spec. 2W

3 = Manuf. Spec. 3W

4 = Manuf. Spec. 4W

5 = Manuf. Spec. 5W

6 = Manuf. Spec. 6W

0 NET

P0711 DeviceNet Reading #3 0 to 1199 0 NET

P0712 DeviceNet Reading #4 0 to 1199 0 NET

P0713 DeviceNet Reading #5 0 to 1199 0 NET

P0714 DeviceNet Reading #6 0 to 1199 0 NET

P0715 DeviceNet Writing #3 0 to 1199 0 NET

P0716 DeviceNet Writing #4 0 to 1199 0 NET

P0717 DeviceNet Writing #5 0 to 1199 0 NET

P0718 DeviceNet Writing #6 0 to 1199 0 NET

P0719 DNet Network Status 0 = Ofﬂine

1 = Online, Not Conn.

2 = Online, Connect.

3 = Conn. Timed out

4 = Link Failure

5 = Auto-Baud

ro NET

P0720 DNet Master Status 0 = Run

1 = Idle

ro NET

P0721 CANopen Comm. Status 0 = Disabled

1 = Reserved

2 = Comm. Enabled

3 = Error Ctrl. Enab

4 = Guarding Error

5 = Heartbeat Error

ro NET

P0722 CANopen Node State 0 = Disabled

1 = Initialization

2 = Stopped

3 = Operational

4 = Preoperational

ro NET

Quick Reference of Parameters, Alarms and Faults

English

20 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0740

Proﬁbus Comm. Status 0 = Disabled

1 = Access Error

2 = Ofﬂine

3 = Conﬁg. Error

4 = Param. Error

5 = Clear Mode

6 = Online

ro NET

P0741

Proﬁbus Data Proﬁle 0 = PROFIdrive

1 = Manufacturer

1

NET

P0742 Proﬁbus Reading #3 0 to 1199 0 NET

P0743 Proﬁbus Reading #4 0 to 1199 0 NET

P0744 Proﬁbus Reading #5 0 to 1199 0 NET

P0745 Proﬁbus Reading #6 0 to 1199 0 NET

P0746 Proﬁbus Reading #7 0 to 1199 0 NET

P0747 Proﬁbus Reading #8 0 to 1199 0 NET

P0750 Proﬁbus Writing #3 0 to 1199 0 NET

P0751 Proﬁbus Writing #4 0 to 1199 0 NET

P0752 Proﬁbus Writing #5 0 to 1199 0 NET

P0753 Proﬁbus Writing #6 0 to 1199 0 NET

P0754 Proﬁbus Writing #7 0 to 1199 0 NET

P0755 Proﬁbus Writing #8 0 to 1199 0 NET

P0918 Proﬁbus Address 1 to 126 1 NET

P0922

Proﬁbus Teleg. Sel. 2 = Std. Teleg. 1

3 = Telegram 103

4 = Telegram 104

5 = Telegram 105

6 = Telegram 106

7 = Telegram 107

8 = Telegram 108

2

NET

P0963

Proﬁbus Baud Rate 0 = 9.6 kbit/s

1 = 19.2 kbit/s

2 = 93.75 kbit/s

3 = 187.5 kbit/s

4 = 500 kbit/s

5 = Not Detected

6 = 1500 kbit/s

7 = 3000 kbit/s

8 = 6000 kbit/s

9 = 12000 kbit/s

10 = Reserved

11 = 45.45 kbit/s

ro NET

P0967

Control Word 1 Bit 0 = ON

Bit 1 = No Coast Stop

Bit 2 = No Quick Stop

Bit 3 = Enable Operation

Bit 4 = Enable Ramp

Generator

Bit 5 = Reserved

Bit 6 = Enable Setpoint

Bit 7 = Fault Acknowledge

Bit 8 = JOG 1 ON

Bit 9 = Reserved

Bit 10 = Control by PLC

Bit 11 to 15 = Reserved

ro NET

Quick Reference of Parameters, Alarms and Faults

English

MW500 | 21

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P0968

Status Word 1 Bit 0 = Ready to Switch ON

Bit 1 = Ready to Operate

Bit 2 = Operation Enabled

Bit 3 = Fault Present

Bit 4 = Coast Stop Not

Active

Bit 5 = Quick Stop Not

Active

Bit 6 = Switching ON

Inhibited

Bit 7 = Warning Present

Bit 8 = Reserved

Bit 9 = Control Requested

Bit 10 to 15 = Reserved

ro NET

P1000 SoftPLC Status 0 = No Application

1 = Installing App.

2 = Incompatible App.

3 = Stoped App.

4 = App. Running

ro READ,

SPLC

P1001 SoftPLC Command 0 = Stop Program

1 = Run Program

2 = Delete Program

0 SPLC

P1002 Scan Cycle Time 0 to 65535 ms ro READ,

SPLC

P1010 SoftPLC Parameter 1 -32768 to 32767 0 SPLC

P1011 SoftPLC Parameter 2 -32768 to 32767 0 SPLC

P1012 SoftPLC Parameter 3 -32768 to 32767 0 SPLC

P1013 SoftPLC Parameter 4 -32768 to 32767 0 SPLC

P1014 SoftPLC Parameter 5 -32768 to 32767 0 SPLC

P1015 SoftPLC Parameter 6 -32768 to 32767 0 SPLC

P1016 SoftPLC Parameter 7 -32768 to 32767 0 SPLC

P1017 SoftPLC Parameter 8 -32768 to 32767 0 SPLC

P1018 SoftPLC Parameter 9 -32768 to 32767 0 SPLC

P1019 SoftPLC Parameter 10 -32768 to 32767 0 SPLC

P1020 SoftPLC Parameter 11 -32768 to 32767 0 SPLC

P1021 SoftPLC Parameter 12 -32768 to 32767 0 SPLC

P1022 SoftPLC Parameter 13 -32768 to 32767 0 SPLC

P1023 SoftPLC Parameter 14 -32768 to 32767 0 SPLC

P1024 SoftPLC Parameter 15 -32768 to 32767 0 SPLC

P1025 SoftPLC Parameter 16 -32768 to 32767 0 SPLC

P1026 SoftPLC Parameter 17 -32768 to 32767 0 SPLC

P1027 SoftPLC Parameter 18 -32768 to 32767 0 SPLC

P1028 SoftPLC Parameter 19 -32768 to 32767 0 SPLC

P1029 SoftPLC Parameter 20 -32768 to 32767 0 SPLC

P1030 SoftPLC Parameter 21 -32768 to 32767 0 SPLC

P1031 SoftPLC Parameter 22 -32768 to 32767 0 SPLC

P1032 SoftPLC Parameter 23 -32768 to 32767 0 SPLC

P1033 SoftPLC Parameter 24 -32768 to 32767 0 SPLC

P1034 SoftPLC Parameter 25 -32768 to 32767 0 SPLC

P1035 SoftPLC Parameter 26 -32768 to 32767 0 SPLC

P1036 SoftPLC Parameter 27 -32768 to 32767 0 SPLC

Quick Reference of Parameters, Alarms and Faults

English

22 | MW500

Param.

Description

Adjustable

Range

Factory

Setting

User

Setting

Properties Groups

P1037 SoftPLC Parameter 28 -32768 to 32767 0 SPLC

P1038 SoftPLC Parameter 29 -32768 to 32767 0 SPLC

P1039 SoftPLC Parameter 30 -32768 to 32767 0 SPLC

P1040 SoftPLC Parameter 31 -32768 to 32767 0 SPLC

P1041 SoftPLC Parameter 32 -32768 to 32767 0 SPLC

P1042 SoftPLC Parameter 33 -32768 to 32767 0 SPLC

P1043 SoftPLC Parameter 34 -32768 to 32767 0 SPLC

P1044 SoftPLC Parameter 35 -32768 to 32767 0 SPLC

P1045 SoftPLC Parameter 36 -32768 to 32767 0 SPLC

P1046 SoftPLC Parameter 37 -32768 to 32767 0 SPLC

P1047 SoftPLC Parameter 38 -32768 to 32767 0 SPLC

P1048 SoftPLC Parameter 39 -32768 to 32767 0 SPLC

P1049 SoftPLC Parameter 40 -32768 to 32767 0 SPLC

P1050 SoftPLC Parameter 41 -32768 to 32767 0 SPLC

P1051 SoftPLC Parameter 42 -32768 to 32767 0 SPLC

P1052 SoftPLC Parameter 43 -32768 to 32767 0 SPLC

P1053 SoftPLC Parameter 44 -32768 to 32767 0 SPLC

P1054 SoftPLC Parameter 45 -32768 to 32767 0 SPLC

P1055 SoftPLC Parameter 46 -32768 to 32767 0 SPLC

P1056 SoftPLC Parameter 47 -32768 to 32767 0 SPLC

P1057 SoftPLC Parameter 48 -32768 to 32767 0 SPLC

P1058 SoftPLC Parameter 49 -32768 to 32767 0 SPLC

P1059 SoftPLC Parameter 50 -32768 to 32767 0 SPLC

Notes:

ro = Read only parameter.

V/f = Parameter available in V/f mode.

cfg = Configuration parameter, value can only be changed with the motor stopped.

VVW = Parameter available in V VW mode.

Page is loading ...

WEG MW500 Quick start guide

WEG MW500 Quick start guide

in other languages

Related papers

Other documents