EN
Remote control for blackout blinds
TYXIA 1705
EN
32
1/ Location/Mounting 4
1.1 Mounted on the wall 4
1.2 Placed on a at surface 5
2/ Wireless association 6
2.1 Associating a motor or receiver 6
2.2 Associate multiple motors
or receivers 9
3/ Save the favourite positions 10
4/ Use 11
5/ Troubleshooting 13
ContentsTechnical characteristics
• Power supplied by 3V lithium battery, CR2430
• Class III insulation
• X3D Transmission frequency:
868.7 MHz to 869.2 MHz
• Maximum radio power < 10 mW
• Receiver category II
• Wireless range: 100 to 300 metres outside,
variable depending on the associated equipment
(the range can vary depending on the installation
conditions and the electromagnetic environment)
• Mounted on a base
• Dimensions: 46 x 121 x 10.7 mm
• Degree of protection: IP 40
• Operating temperature: 0 to +55°C
• Storage temperature: -10 to +70°C
• Installation in an environment with normal
pollution levels
EN
54
1.2 Placed on a flat surface
1/ Location/Mounting
1.1 Mounted on the wall
WARNING !
Do not ingest battery, chemical Burn Hazard.
This product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the
product and keep it away from children.
If you think batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.
EN
76
> 3s
2/ Wireless association
This chapter allows you to associate a remote
control with one or more X3D wireless motor(s),
X3D roller shutter receiver(s).
You can associate up to 16 receivers or motors.
2.1 Associating a motor or receiver
2.1.1 A single motor is turned on
❶ Set the motor or receiver to association standby
mode.
❷ On the remote control press
and at the
same time and hold for 3 seconds, until the LED
ashes. Release.
When receiver is found, the LED lights up green brie y.
❸ After a few seconds, the shutter starts twice to
con rm the association.
The receiver LED is off.
The association mode is automatically exited
❶ Activating association standby mode
- Motor:
1) Upon turning on for the rst time, if the motor
was not associated before.
2) From a remote control used for the motor
(already associated) press the
button for 3
seconds.
- Receiver: press its button for 3 seconds until the
LED ashes.
EN
98
2/ Wireless association
2.1.2 Multiple motors or receivers are in association
standby mode and you only want to associate one
❶ On the remote control press
and at the
same time and hold for 3 seconds, until the red
LED ashes. Release.
The remote control searches the different motors or
receivers.
The LED ashes red, then briey green as soon as a
new receiver is found.
❷ When the LED starts ashing red slowly, press
the button as many times as required to select
the motor (receiver) to associate.
The corresponding shutter activates briey.
❸ Once the motor (receiver) has been found, press
.
❹ After a few seconds, the shutter starts twice to
conrm the association.
To exit association mode, press for 3 seconds.
2.2 Associate multiple motors or receivers
Important: if you associate several motors with
the remote control, you will no longer have access
to the stop settings from it.
❶ Set the motors (receivers) to association standby
mode.
❷ On the remote control press
and at the
same time and hold for 3 seconds, until the LED
ashes. Release.
The remote control searches the different motors or
receivers.
The LED ashes red, then briey green as soon as a
new receiver is found.
❸ When the LED starts ashing red slowly, press
and at the same time and hold for 3
seconds until the red LED turns on.
❹ The shutters are activated briey to conrm the
association.
EN
1110
> 3s
3/ Save the favourite positions
You can save up to 2 favourite positions: and
.
❶ ❷ Set the shutter to the required position e.g.
).
❸ Press or to set the angle of the slats.
❹ Press + or + and hold for 3
seconds to save the position.
The LED changes from red to green if the receiver
has correctly received the information. The shutter is
activated brie y.
Release.
4/ Use
• Press , or to control the roller shutter.
The LED changes from red to green if the receiver has
correctly received the information.
• Press or to set the angle of the slats.
• Press to go to favourite
position 1 (if it has been saved).
• Press to go to favourite
position 2 (if it has been saved).
EN
1312
5/ Troubleshooting
• The red LED fl ashes several
times every time a button is pressed.
The battery is low.
Change the battery.
• Remove an association
- Remove the front face of the
remote control.
- Press button A.
The red LED ashes.
- Press
as many times as
required to select the motor
(receiver) to remove.
- Press the
button.
The shutter starts.
- Press button A to exit.
• Remove all associations
To release the remote control from all association.
- Remove the front face of the remote control.
- Press button A. The red LED ashes.
- Press the
and buttons at the same time and
hold for 3 seconds. The shutters start.
- Press button A to exit.
CR 2430
• Your remote control is lost or not functioning
Initial condition: The lost remote control was only
associated with a single motor (receiver).
From a new remote control:
- Press the B button 2 times, until the LED ashes
orange.
- Press and for 3 seconds until the ashing
stops.
The motor (receiver) has not been associated before
- Restart the association process for your new
remote control.
• The green LED does not fl ash after briefl y
pressing button B.
- Several motors are associated with the remote
control.
Therefore, you cannot access the setting modes in
this case.
The remote control must only be associated with
one motor for the settings.
www.deltadore.com
04/19
/
